modway EEI -1327 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 7
EEI -1327 DESK
Hardware:
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
a Cam x10 b Cam Post x10
c Dowel x16 d Bolt M6x12mm x2
h Allen Wrench x1
e Bolt M6x35 x6 f Bolt M6x40mm x2
g Screw M6x35 x6

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 7
EEI -1327 DESK
Component:
A Top Panel x1 B Left Side Panel x1
A
C Right Side Panel x1 D Bottom Panel x1
E Back Panel x1 F Divide Panel x2
G Shelf x1 H Leg x2
J Center Rail x1 Support Rail x1
B
C
D
E
F F
G
H
H
J
K K
E Back Panel x1 Divide Panel x2
G Shelf x1 H Leg x2
J Center Rail x1 K Support Rail x1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 7
EEI -1327 DESK
HOW TO USE CAN AND CAM POST HARDWARE
STEP 1:
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
Insert 5pcs Cam Posts (a) into the corresponding holes on the Left Side Panel (B) as shown.
Repeat the same steps for the Right Side Panel (C).
a
ax10 Phillips Head Screwdriver
( not included) Hardware & Tools required
B C
a
a
a
a a
a
a
a
a

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 7
EEI -1327 DESK
STEP 2:
STEP 3:
Place the Divide Panels (F) to the Shelf (G).
Connect them by using 4pcs Dowel (c) as shown.
Place the assembled Divide Panels (F) to the Bottom Panel (D).
Connect them by using 4pcs Dowel (c) as shown.
cx4 Hardware & Tools required
Hardware & Tools required
cx4
G
F
F
c
c
c
c
D
c
G F
F
c
c c

Customer Service 908-368-1025︱www.modwayfurniture.com Page 5 of 7
EEI -1327 DESK
bx10 Phillips Head Screwdriver
( not included)
cx4
STEP 4:
STEP 5:
Attach the Back Panel (E) to the Bottom Panel (D) by using 2pcs Screw (g) as shown
Use Allen Wrench (h) to tighten the Screws (g) clockwise until secure.
Place the Top Panel (A) to the Assembled Divide Panels (F).
Attach them by 4pcs Dowel (c) as shown.
Place the Left Side Panel (B) and Right Side Panel (C) to the assembled Bottom Panel (D) and Back Panel (E).
Attach them by using 4pcs Dowel (c) as shown.
Insert 10pcs Cam (b) into the corresponding holes on the Back Panel (E) and Bottom Panel (D).
Use Phillips Head Screwdriver (not included) to tight all the Cams (b).
Hardware & Tools required
Hardware & Tools required
cx4 gx2 hx1
A
D
E
F F
G
g
h g
c
c
c
c
A
E B
C
h
D
c
b
b
b
b
b
b
b
b
b
b
c

Customer Service 908-368-1025︱www.modwayfurniture.com Page 6 of 7
EEI -1327 DESK
STEP 6:
STEP 7:
Attach the 2pcs Leg (H) to the Center Rail (J) by using Bolts () as shown.
Tighten Bolts (f) by using Allen Wrench (h). Do not full tighten.
Attach the 1pc Support Rail (K) to the assembled Center Rail (J) by using 1pc Bolt (d).
Attach the 1pc Support Rail (K) to the assembled Legs (H) by using 1pc Bolt (e).
Use Allen Wrench (h) to tighten the Bolts (d&e) clockwise until secure.
Repeat the same step for the other Support Rail (J).
Hardware & Tools required
Hardware & Tools required
fx2 hx1
J f
H
H
f
h
dx2 ex2 hx1
H
H
J
K K
d
e
d
e
h

Customer Service 908-368-1025︱www.modwayfurniture.com Page 7 of 7
EEI -1327 DESK
STEP 8:
Place the Assembled Bottom Panel (D) to the assembled Legs (H) as shown.
Attach them by using 4pcs Bolt (e) as shown.
Use Allen Wrench (h) to full tight the Bolts (e).
Hardware & Tools required
STEP 9:
Place the desk to your desired position.
Assembly is completed. The desk is ready to enjoy now!
ex4 hx1
e
H
H
D
e
e
e
h