modway EEI-3685 User manual

Page 1 of 3
Thank you for purchasing the MODWAY TABLE!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 15 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Customer Service 609-256-9000 www.modway.com
EEI-3695-NAT
The assembly steps are the same EEI-3719-NAT
EEI-3703-NAT-GRY
The assembly steps are the same EEI-3719-NAT
EEI-3709-NAT
The assembly steps are the same EEI-3719-NAT
EEI-3715-NAT
The assembly steps are the same EEI-3719-NAT
EEI-3685/EEI-3688/EEI-3690/EEI-3695/EEI-3703/EEI-3709
/EEI-3715/EEI-3717/EEI-3719/EEI-3720 TABLE
EEI-3719-NAT
EEI-3717-NAT
The assembly steps are the same EEI-3719-NAT

Page 2 of 3Customer Service 609-256-9000 www.modway.com
EEI-3720-NAT
The assembly steps are the same EEI-3719-NAT
EEI-3685-LGR
The assembly steps are the same EEI-3719-NAT
EEI-3688-NAT
The assembly steps are the same EEI-3719-NAT
EEI-3690-NAT
The assembly steps are the same EEI-3719-NAT
A
B
C
Washer
M9x20mm x 8
Lock Nut
M8x13mm x 8
Wrench M13 x 1
Hardware:
1. Table Top
2. Leg x4
x1
1
2
Component:
EEI-3685/EEI-3688/EEI-3690/EEI-3695/EEI-3703/EEI-3709
/EEI-3715/EEI-3717/EEI-3719/EEI-3720 TABLE

Page 3 of 3
STEP 1:
Hardware & Tool required
STEP 2:
Customer Service 609-256-9000 www.modway.com
1
2
2
2
2
Assembly is complete. Your table is ready to be used now!
Carefully position the assembled table to the desired location.
Attach 1 piece of Leg (2) to Table Top (1).
Then install 2 pieces of Washers (A) and 2 pieces of Lock Nuts (B) on each bolt of the Leg (2).
Use Wrench (C) to secure Lock Nuts (B) as shown.
Repeat the same steps for the other 3 pieces of Legs (2).
x8
B
Cx1
x8
A
A
C
B
EEI-3685/EEI-3688/EEI-3690/EEI-3695/EEI-3703/EEI-3709
/EEI-3715/EEI-3717/EEI-3719/EEI-3720 TABLE