modway MOD-6045 User manual

Customer Service 908-368-1025 www.modway.com Page 1/3
MOD-6045, MOD-6046
Thank you for purchasing the MODWAY BED！
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 20 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all small pieces out of reach of children.
Hardware:
A
B
CWOOD SCREW M4 X 32mm
FLAT WASHER
ALLEN KEY M5
D
E
F
G
H
JCBB BOLT M8 x 25
ALLEN KEY (BALL SHAPE) M4
8 PCS
8 PCS
6 PCS
1 PC
1 PC
1
3
3
2
7
Compenents :
1 - x 1HEADBOARD
2 - x 1
FOOTBOARD
3 - x 2SIDERAIL
4 - x 1
CENTER SUPPORT
4
5
5
5 - x 3SUPPORT LEG
6 - x 2
SUPPORT BAR
7 - x 13
BED SLAT
5
ADJUSTER 3 PCS
JCBC BOLT M6 x 40 9 PCS
6
6
SPRING WASHER 8 PCS

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 2/3
Bx8 Gx8 Fx1
Hardware & Tool required
Hardware & Tool required
Ex1
STEP 1:
Place Headboard (1) , Footboard (2) and Siderail (3) on a carpeted or padded area as shown. Attach Side rail (3) into Headboard
(1) and Footboard (2) by inserting Flat Washer (G), Spring washer(H) and JCBB 25mm Bolt (B) into the holes of Headboard (1)
and Footboard(2). Tighten with M5 Allen Key (F).
STEP 2:
1. Attach the Support Bar (6) to the predrilled hole at center of Headboard (1) by using JCBC bolt 40MM(A) and tighten by using M4 Allen Key(E).
Repeat the same step at Footboard(2), then place Center Support bar(4) on the Support Bar(6),attach JCBC bolt 40MM(A) at predrill hole and
tighten by using M4 Allen Key(E).
2. Place the Center Support Bar(4) as per picture shown and attach JCBC bolt 40MM(A) and tighten using M4 Allen Key(E). Repeat again at
Footboard(2)
3.Attach the Adjuster(D) to the two Center Support Leg(5).
4. Attach the Center Support Leg(5) to the Center support bar(4) as shown in diagram., Insert JCBC 40MM (A) to the predrilled hole and tighten by
using M4 Allen Key(E)
Dx3Ax9
Hx8
MOD-6045, MOD-6046
6
E
4
E
A
A
4
5
D
E
F
B
H
G
3

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 3/3
Cx6
Hardware & Tool required
STEP 3:
Attach Slat (7) into bed by inserting CSK screw (C) into the predrilled holes on the Slat (7) . Tighten with Screwdriver (Not
provided) .
Assembly is completed. The bed is ready to enjoy now!
Screwdriver (Not provided) .
MOD-6045, MOD-6046