modway EEI-2120 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI – 2120 OFFICE CHAIR
Component:
A Chair Back x1
Thank you for purchasing the MODWAY OFFICE CHAIR！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the office chair, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
A
Caster x5
G
F
G
Chair Base x1
G G
G G F
B
B
B Armrest x2 D Control Mechanism x1
E Cylinder x1
D
E
Hardware:
1 Bolt M8x20mm x2
7 Allen Wrench M5 x1
3 Bolt M8x30mm x4
4 Bolt M8x50mm x4
C
C Chair Seat x1
2 Bolt M8x25mm x2
5 Flat Washer x8
8 Allen Wrench M6 x1
6 Plastic Washer x2
Note: 1,2,3,5,6 assembled at the bottom of the chair back;

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI – 2120 OFFICE CHAIR
STEP 1:
STEP 2:
Please put Chair Base (F) upside down on a carpeted or padded surface.
Insert 1pc of Castor (G) into the Chair Base (F) as shown by hand.
Repeat the same steps for the remaining 4pcs of Castor (G).
G
G
G
G
G
F
Flip the assembled Chair Base (F) with Castors (G) on the floor.
Insert the bottom end of Cylinder (E) into the assembled Chair Base (F) as shown.
E
F
G
G
G
G
G

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI – 2120 OFFICE CHAIR
5
C
A
5
5
5 5
3
3 3
3
3
7
2
5
6
6
6
5
1
5
5
5
5 1
1
2
1
2 2
STEP 3:
STEP 4:
Flip the Chair Back (A) upside down, with the metal plate on the bottom side of the Chair Back (A) facing up, line up the 4
holes with the ones on the back of the Chair Seat (C).
Attach Chair Back (A) to the bottom of Chair Seat (C) by using 4 pieces of Bolt (3) and Flat Washer (5) as shown.
Tighten Bolts (3) by using Allen Wrench (7) clockwise until secure.
1x2pcs 2x2pcs 5x4pcs 6x2pcs 7x1ps Hardware & Tool required
3x4pcs 5x4pcs 7x1pc Hardware & Tool required
6
6 C
Place 2 pieces of Plastic Washer (6) to the two front holes on the bottom of the Chair Seat (C) as shown.
Attach Control Mechanism (D) to the Chair Seat (C) by using 2 pieces of Bolt (1) and 2 pieces of Bolt (2) with 4
pieces of Flat Washer (5) as shown.
Bolts (2) should be connected with Flat Washers (5) and Plastic Washers (6) on the front holes as shown.
Tighten Bolts (1&2) by using Allen Wrench (7) clockwise until secure.
7
C
D

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI – 2120 OFFICE CHAIR
4
STEP 5:
STEP 4:
Attach Armrest (B) to the side of assembled Chair Back (A), Chair Seat (C) and Control Mechanism (D) by using 4 pieces
of Bolt (4) as shown.
Secure Bolts (4) by using Allen Wrench (8) clockwise until secure.
4x4pcs 8x1pc Hardware & Tool required
Please insert the bottom holes of Control Mechanism (D) into the top end of Cylinder (E) and Chair Base (F) as shown.
4
4
4
B
B
A
C
D
Assembly is complete. The office chair is ready to be enjoyed now!
D
E
8
F