modway MOD-6131 User manual

MOD-6131 QUEEN BED
Customer Service 609-256-9000︱www.modway.com Page 1of 5
Thank you for purchasing the MODWAY BED!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all the pieces out of reach of children.

MOD-6131 QUEEN BED
Customer Service 609-256-9000︱www.modway.com Page 2of 5
Hardware:
* Not include hardware bag
Components:
1. Headboard x1 2. Side Rail x2 3. Footboard x1 4.Support Plate x2
Bolt M6x40mm x8
Bolt M6x25mm x12
Flat Washer x22
Spring Washer x8
Allen Wrench x1
Twin Screw 5/16*114mm x4
B.
Bolt M6x50mm x2
C.
D.
E-1.
F.
G.
A.
H.
I.
Crescent Spacer x8
Wrench x2
J.
Nut x8
E-2. Spring WasherM6 x8
K. Corner Bracket x2
L. Screw 40mm x8
5. Central Leg x3 6. Central Rail x1 7.Slat x13 8. Leg x4
M. Screw driver x1

MOD-6131 QUEEN BED
Customer Service 609-256-9000︱www.modway.com Page 3of 5
STEP1:
1. Attach 2 pieces of Legs (8) to the Headboard (1) by using 4 pieces of Bolts (B) with 4 pieces of
Flat Washers(D) and 4 pieces of Spring Washers (E-2) as shown.
2. Repeat the same Step to assemble 2 pieces of Legs (8) to the Footboard (3).
3. Attach1 piece of Support Plate (4) to the Footboard (3) by using 2 pieces of Bolts (A) with 2 pieces of
Flat Washers(D) as shown.
4. Use Allen Wrench (F) to tighten all Bolts (A) and Bolts (B) clockwise as shown.
STEP 2:
1. Attach 2 piece of Side Rails(2) to the Headboard(1) by using 4 pieces of Twin Screws (G) with 8 pieces of
Crescent Spacers(H), 8 pieces of Spring Washers (E-1) and 8 pieces of Nuts (I) as shown.
2. Attach 2 piece of Side Rails (2) to the Footboard (3) by using 2 pieces of Corner Brackets (K)with 12
pieces of Bolts(C) and 12 pieces of Flat Washers(D)as shown.
3. Use 2 pieces of Wrenchs (J) to tighten all Nuts (I) clockwise as shown.
4. Use Allen Wrench (F) to tighten all Bolts (C) clockwise as shown
Pre-installed

MOD-6131 QUEEN BED
Customer Service 609-256-9000︱www.modway.com
Page 4of 5
STEP 3.
1. Tighten 3 pieces of Central Legs (5) to the Central Rail (6)clockwise until secure by hand as shown.
2. Insert 1 piece of Central Rail (6) into the Support Plates (4) by hand as shown.
STEP 4:
1. Put 13 pieces of Slats (7)on the Rails as shown.
2. Use Screw driver (M) to tighten 8 pieces of Screws(L) clockwise as shown.
M
L

MOD-6131 QUEEN BED
Customer Service 609-256-9000︱www.modway.com
Page 5of 5
Your bed is ready to be used now!