modway EEI –2853 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI –2853 BOOKCASE
Thank you for purchasing the MODWAY BOOKCASE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the bookcase, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
3 Allen Wrench M4 x1
Component:
A Top Panel x1
D
Leg x4
B
Metal Frame x3
D
1 Bolt M6x12mm x36
2 Castor x4
A
B
C
B
C
A
A
B
B
C Shelf x2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI –2853 BOOKCASE
STEP 1:
STEP 2:
Put 1 piece of Shelf (C) upside down on a carpeted or padded surface.
Place 1 piece of Metal Frame (A) to Shelf (C) as shown.
Insert 4 pieces of Bolt (1) into the pre-drilled holes on Shelf (C) through the pre-drilled holes on Metal Frame (A).
Use Allen Wrench (3) to tighten Bolts (1). Do not fully tighten Bolts (1) at this step.
Repeat the same steps for the remaining 1 piece of Shelf (C) and 1 piece of Metal Frame (A).
Hardware & Tools required
Hardware & Tools required
1x8 3x1
1x24 3x1
Put 1 piece of Metal Frame (A) upside down on a carpeted or padded surface.
Place 4 pieces of Leg (B) to Metal Frame (A) as shown.
Insert 8 pieces of Bolt (1) into the pre-drilled holes on Metal Frame (A) through the pre-drilled holes on Legs (B).
Repeat the same steps for the 2 pieces assembled Metal Frame (A) and Shelf (C).
Use Allen Wrench (3) to tighten all the Bolts (1). Do not fully tighten all the Bolts (1) at this step.
B
1
A
C
1
3
1
1
C
A
C
A
A
B
B
B
B
A
1 1
1
1
1
1
1
1
1
1
1 1
1
1
1
1
1
1
1 1
1
1
1
1
1
1
3

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI –2853 BOOKCASE
STEP 3:
STEP 3:
Tighten 4 pieces of Castor (2) into the bottom of assembled Legs (B) by hand clockwise until secure as shown.
Hardware & Tools required
Hardware & Tools required
5
D
B
2x4
Put Top Panel (D) upside down on a carpeted or padded surface.
Place the assembled Metal Frame (A), Legs (B), and Shelves (C) to Top Panel (D) as shown.
Insert 4 pieces of Bolt (1) into the pre-drilled holes on Top Panel (D) through the pre-drilled holes on Metal Frame (A).
Use Allen Wrench (3) to tighten all the Bolts (1) clockwise until secure at this step.
B
B
4
3
D
1x4 3x1
A
A
A
C
C
B
B B
B
2
2
2
2
A
A
A
C
C
C
B
1 1
1
1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI –2853 BOOKCASE
STEP 5:
Carefully turn over the assembled bookcase.
Assembly is complete. Your bookcase is ready to be used now!