
~~
.
fflOHU®
Sal
X
oO
□
Oo
M
0 0
□
□
0 0
□
0
□
0
□
0,,,,,,,,,,-
-----
(1
()mmmiim,,
---------
l)
llmmmam,..
- - -
--
- - -
(1
v··--
·-
-vzummmm:-
----- l)
---~
0-
- ~
[
-·!--+-----.....,,
-•-
[ 0 ]
►
INSTRUCTIONS
FIRSTSTAGE AMPLIFIED INDOOR / OUTDOOR HDTV ANTENNA
BOX INCLUDES
Antenna Mounting Hardware
Mounting Brackets
x4 - Screws x2 - Hex Bolts
x4 - Washers x2 - Flange Nuts
30 ft. Coaxial Cable x4 - 50mm Screws x4 - Sealing Pads
Mast Base
Sail Antenna
x2 - Wing Nuts x1 - Mast End Cap
x1 - U-Bolt
Power Injector USB Power Adapter* Mast
*Actual USB power adapter may dier in appearance.
IMPORTANT
FOLLOW ALL SAFETY PROCEDURES, WARNINGS, AND MOUNT THE ANTENNA AT LEAST 20 FT. FROM ALL
INSTRUCTIONS WHEN INSTALLING YOUR ANTENNA. POWER LINES OR UTILITY POLES.
SAFETY PROCEDURES POWER LINE WARNING
- Make sure there is another person present (on the ground) while If you intend to mount the antenna on a rooftop, make sure to
installing the antenna. mount it at least 20 ft. away from any power lines or utility poles.
- DO NOT attempt to mount the antenna on a windy, rainy, or
snowy day.
Select mounting location; Connect one end of the 30 ft. Coaxial
ideally wood framework Cable to the connector on the antenna
indoors (in attic) or outdoors (see illustration below) and connect the
(roof/siding).
3
other end of the Coaxial Cable to the
Power Injector.
Position the Mast Base (flat Note: Excessive cable length may cause reception
surface to wood) to create an loss.
1
“ ” shape when viewed from
straight on. Connect the coaxial cable from the
Power Injector to the ANT/IN connector
Mark the Mast Base position on on the back of the TV.
the surface and drill pilot holes,
1 ½” deep, for each of the 50mm
Screws. For outdoor installation,
place the Sealing Pads over the
pilot holes, and the Mast Base on The Power Injector must be powered in
top of the Sealing Pads. Tighten order to function. Plug the Power
the four 50mm Screws.
4
Injector’s USB cable into an open USB
port on the back of the TV.
If the TV does not have a USB port, use
the included USB Power Adapter with any
Place the U-Bolt under the standard 120V wall outlet.
Mounting Bracket, and secure the Note: If using an RF
Mounting Bracket to the antenna splitter, follow the RF
splitter installation
using the four Screws and instructions on the
Washers. Place the other back of this page.
Mounting Bracket on the U-Bolt
and add the Wing Nuts.
2
Place the Mast End Cap on the
long end of the Mast. Insert the
Mast between the Mounting 30 ft.
Coaxial Cable
Brackets and tighten the Wing
Nuts. Power Injector
Insert the short end of the Mast
into the Mast Base. Use the two Coaxial
POWER OPTIONS:
Hex Bolts to secure the Mast to Cable
USB Cable (attached) (attached)
the Mast Base.
a. TV's USB Port Back of TV
OR
ANT/IN
b. Wall Outlet
If you have any diculties with the installation of your antenna, please contact Mohu®.
Si tiene alguna dificultad instalando su antena, por favor contacte a Mohu®.
II II
Continued