Molpir FMS5723 User manual

FMS57
23
-
HH
-
60
+
INSTALLATION MANUAL FOR 7“DIGITAL
MONITOR WITH 60° TIPPING HOLDER
1. Material eeded for i stallatio
2. Tools eeded for i stallatio :
Screwdriver
PH2
Screwdriver
PH0
Monitor holder with 60° tipping
pos.no.6
Pl stic fr me of the monitor
pos.no.2
Screws:
8 pcs M5 x 10mm – pos.no.3
2 pcs
M2 x 6mm
–
pos.no
.4
Monitor c bling
pos.no.5
FMS5723
D
te
27
/0
7
/201
1
P ge
1 /
5
NM_FMS5723_002_27072011_EN
Ord
.
code
:
FMS5723
Monitor
–
pos.no
.1
068988
-
M
Second ry rrestment - pos.no.7

3. I stallatio procedure
Step 1: Insert met l holder of the monitor into the se t (pos.no.6) nd fix it
with 3 screws M5 x 10mm (pos.no.3) trough holes m rked with
rings.
Step 2: Inst ll tion of the monitor c bling:
1) Connect the c bling (pos.no.5) (FMS-CA04-........) into the
monitor connector
2) Insert the c bling (pos.no.5) into the groove on the re r side of
the monitor
3) Apply the dhesive t pe to void th t the c bling f ll out from
the groove
Figure
2
–
monitor c bling
Figure
1
–
Fix tion of the hinge on the
se t
with
screws
3
2
1
D te 27/07/2011 P ge 2 / 5
NM_FMS5723_002_27072011_EN

Step 3: Pl cing monitor on the holder
1) Direct hooks on the re r side of monitor to the T-holes in the
holder (pos.no.6) nd the monitor (pos.no.1) push down s
much s possible.
2) Fix the monitor with two screws M2 x 6mm (pos.no.4) to the
monitor holder
Figure
3
–
H nging
of m
onitor on the hinge
hooks
hooks
Figure 4 – fix tion of
monitor on the hinge
D te 27/07/2011
P ge
3
/ 5
NM_FMS5723_002_27072011_EN
PUSH

Step 4: Insertion of AUX-IN nd SPK-OUT c bling (only if necess ry)
1) Connect connectors (m le plug with fem le plug)
2) Insert connected connectors into the second ry rrestment
(pos.no.7)
3) By closing of second ry rrestment the connection is secured
g inst its unw nted disconnection
Step 5: Inst ll tion of the pl stic fr me of the monitor
1) Tilt the monitor into 45° ~ 60° ngle
2) Insert the pl stic fr me (pos.no.2) on the tipping monitor
(pos.no.1) with the holder (pos.no.6)
Figure 5 - AUX-IN nd SPK-OUT c bling
conne
ction
Figure
6
–
Insert monitor with hinge into the fr me
D te 27/07/2011 P ge
4
/ 5
NM_FMS5723_002_27072011_EN

Step 6: Fix tion of the pl stic fr me
1) Tilt the monitor nd tighten 3 screws M5 x 10mm (pos.no.3)
into the holes (m rked with rings)
2) Give the monitor to the b sic position, in the one line with the
fr me (pos.no.2) nd tighten rem ining 2 screws M5 x 10mm
(pos.no.3) into the holes on the top of the fr me, m rked with
rings.
D te 27/07/2011
P ge
5
/ 5
NM_FMS5723_002_27072011_EN