Mono FG149 User manual

FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) 4/5/10-Tray | Steam
www.monoequip.com
Bx OVEN
Eco-connect
Installation and Operation Manual
Oven Serial Number _________________________________
Oven Code 149 150 153 158 159 170
Condenser Serial Number ____________________________ (if fitted)
In the event of an enquiry, please quote these serial numbers.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
2MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 3
ATTENTION
If oven fails to heat up, when first connected to a power supply or during
use at any time, press the reset buttons located on the rear back panel.
(Do not remove the back panel)
Rear View
4 Tray Oven
Hole Location for Reset Button
Hole can be at position 1 or 2
depending on the oven model
Rear View
10 Tray Oven
Hole Location for Reset Button
Hole can be at position 1 or 2
depending on the oven model
If this fails to correct the situation, please contact your supplier.
2
1
1 2

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
4MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
Safety symbols
The following safety symbols are used throughout this document and manual (available at www.monoequip.com).
Before using your new equipment, read the instruction manual carefully and pay special attention to information
marked with the following symbols
Warning! Indicates a hazardous situation which, if not avoided,
could result in death or severe injury.
Warning! Indicates a hazardous situation which, if not avoided,
could result in death or severe injury.
Caution! Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 5
Electrical safety and advice regarding supplementary
electrical protection
Commercial kitchens and food service areas are environments where electrical appliances may be located close to
liquids or operate in and around damp conditions or where the restricted movement for installation and service is
evident.
The installation and periodic inspection of the appliance should only be undertaken by a qualified, skilled, and
competent electrician and connected to the correct power supply suitable for the load as stipulated by the
appliance data label.
The electrical installation and connections should meet the necessary requirements of the local electrical wiring
regulations and any safety guidelines.
We recommend:-
Supplementary electrical protection with the use of a Residual Current Device (RCD)
Fixed wiring appliances should also incorporate a locally situated switch disconnector to
connect to, which is easily accessible for switching off and safe isolation purposes. The
switch disconnector must meet the specification requirements of IEC 60947.
Your attention is drawn to:-
BS 7671:2018 – Guidance Note 8 – 8.13: Other locations of increased safety risk
It is recognised that there may be locations of increased risk of electrical shock other than those specifically
addressed in Part 7 of BS 7671. Examples of such locations could include laundries where there are washing and
drying machines in close proximity and water is present, and commercial kitchens with stainless steel units, where
once again, water is present. Where, because of the perception of additional risks being likely, the installation
designer decides that an installation or location warrants further protective measures, the options available
includes:
Automatic Disconnection of Supply (ADS) by means of a residual current device having a residual
operating current not exceeding 30 mA;
Supplementary protective equipotential bonding; and
Reduction of maximum fault clearance time.
The provision of RCDs and supplementary bonding must be specified by the host organisation’s appointed
installation designer or electrical contractor and installed by a suitably qualified and competent electrician so as to
comply with Regulations 419.2 and 544.2.
Warning! A 30mA RCD must protect the supply to this machine.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
6MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
Contents
Page
1. Introduction............................................................................................................. 8
2. Specifications ......................................................................................................... 10
Mechanical specifications..................................................................................................................... 10
Electrical specifications ........................................................................................................................ 10
3. Safety....................................................................................................................... 11
4. Installation............................................................................................................... 12
Power.................................................................................................................................................... 12
Water .................................................................................................................................................... 13
Ventilation............................................................................................................................................. 13
Before use ............................................................................................................................................ 13
Before use ............................................................................................................................................ 13
Ambient working temperatures............................................................................................................. 13
5. Isolation....................................................................................................................15
Electrical supply.................................................................................................................................... 15
Water supply......................................................................................................................................... 15
6. Touchscreen Operations ....................................................................................... 16
Starting and operating using ready-made recipes (programs)............................................................. 17
Manual bake (no program mode) ......................................................................................................... 21
Setting the time and date...................................................................................................................... 22
Setting up a new program .................................................................................................................... 25
Multi bake operation ............................................................................................................................. 28
7–Day Timer ......................................................................................................................................... 31
Putting the oven into Standby mode .................................................................................................... 33
Putting the oven into Sleep mode ........................................................................................................ 33
User settings (oven setup).................................................................................................................... 34
Factory settings (oven setup) ............................................................................................................... 37
Changing the passwords ...................................................................................................................... 39
Diagnostics ........................................................................................................................................... 41
7. Using the USB port................................................................................................. 43
Using the USB port to import recipes ................................................................................................... 43

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 7
8. Cleaning .................................................................................................................. 49
Daily cleaning instructions .................................................................................................................... 49
Weekly cleaning instructions ................................................................................................................ 49
9. Maintenance............................................................................................................ 54
General maintenance ........................................................................................................................... 54
Steam system maintenance ................................................................................................................. 54
Light bulb replacement ......................................................................................................................... 54
10. Spares Information................................................................................................. 56
11. Condenser Unit (Option) ........................................................................................ 90
12. Passwords............................................................................................................... 108

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
8MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
1. Introduction
Thank you for purchasing this MONO Bx Eco oven.
“A combination of clean industrial design and the latest technology.”
The MONO BX oven range is designed to take the baking Industry’s standard trays.
Ovens in the range are of stainless steel construction and selected models have removable tray racks
to aid cleaning.
The smaller ovens are designed to be stackable without separate support, so your business can grow
without taking up more ground space.
The high-speed fans, elements and steam systems give efficient air circulation to produce a professional
bake across a product range.
The doors are double-glazed to increase the efficiency of the ovens well-insulated baking chamber.
Ovens are fitted with user-friendly touchscreen display panels. A voice prompt facility is also available for
the basic instructions like “Bake over”.
The 10-tray Bx is supplied with a 10-tray capacity stainless steel base with locking castors.
An optional condenser unit can be fitted to any Bx oven or stacked Bx ovens, as required. It can be
adjusted with the thermostatic control to operate in most ambient temperatures.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 9
Figure 1: BX oven features
A. Power on/off switch
B. Identification / Serial number plate.
C. Touchscreen
D. Damper flue – do not cover the flue
Figure 2: Optional condenser

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
10 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
2. Specifications
Mechanical specifications
Table 1: Mechanical specifications
4/5-trays oven 10-trays oven
FG159 FG153 FG158 FG150 FG149 FG170
Tray size
18 in.
x
30 in.
40 cm
x
60 cm
60 cm
x
40 cm
18 in.
x
30 in.
40 cm
x
60 cm
40 cm
x
80 cm
Height (oven only) 525 mm 525 mm 570 mm 1170 mm 1170 mm 1170 mm
Height (oven + base) – – – 1870 mm 1870 mm 1870 mm
Width 840 mm 780 mm 1000 mm 840 mm 780 mm 780 mm
Depth – door closed (1) 1269 mm 1103 mm 890 mm 1309 mm 1109 mm 1309 mm
Depth – door open (1)(2) 1828 mm 1610 mm 1610 mm 1870 mm 1609 mm 1809 mm
Weight (kg) 165 115 110 290 250 262
(1) Includes the handle.
(2) Excluding the services.
Electrical specifications
Power supply
Warning! A 30mA Residual Current Device (RCD) must protect the supply to this machine.
Always fit a wall isolator to isolate the oven completely. The isolator must be
visible, labelled clearly, and easily accessible by an operator.
Table 2: Oven supply specifications
Please check the identification plate for other countries.
4 or 5-tray ovens 240 Vac (50 Hz), 1 phase
415 Vac (50 Hz), 3 phase + neutral + earth
10-tray ovens 380 to 400 Vac (50 Hz), 3 phase + neutral + earth
415 Vac (50 Hz), 3 phase + neutral + earth
Display
7-inch HD TFT resistive touchscreen, portrait format

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 11
3. Safety
The Bakery Manager or Supervisor must carry out daily safety checks. Bakery staff must not, under any
circumstances, remove panels to access any part of the oven.
Only fully-trained and authorised persons are permitted to do any work on the oven. Authorised electricians must
carry out all repairs and maintenance of electrical units. Always disconnect or isolate the power supply before
starting any maintenance (i.e. opening panels) or cleaning work on the oven.
Warning! Before using the oven, check that:
All cover panels and pipe fittings are secure.
The door handles are not damaged.
If the oven is damaged or malfunctioning, stop using it.
Do not attempt any repairs.
Contact the Mono Service Department for advice.
Fit only MONO spare parts to this oven.
All connections to the oven must comply with the statuary requirements of the
country of installation.
Operate the oven only as described in this manual.
Warning! A 30mA RCD must protect the supply to this machine.
Always fit a wall isolator to isolate the oven completely. The isolator must be
visible, labelled, and easily accessible by an operator.
Caution! Be aware of hot surfaces:
Always use oven gloves when loading or unloading the oven.
Allow time for the oven to cool down before cleaning it. To prevent door
glass from shattering, do not clean the oven glass when hot.
While the oven is in operation (and for some time after use), it is
inadvisable to touch the oven window or the surrounds because of
conducted heat.
The oven owner is legally obliged to instruct staff on these safety points and
the safe operation of the oven. Therefore, these instructions should not be
removed from the working area.
Do not store items on top of or behind the oven.
Only use the oven for baking bread, pastries, and cakes.
Contact Mono Equipment for other product-making machines.
No unauthorised modifications to the oven are permitted.
Only use MONO spare parts.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
12 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
4. Installation
Power
Warning! A 30mA Residual Current Device (RCD) must protect the supply to this machine.
Always fit a wall isolator to isolate the oven completely. The isolator must be
visible, labelled clearly, and easily accessible by an operator.
Figure 3: Main power supply connections
Note
L2 and L3 are for three-phase installations only.
See the Specifications section for electrical specifications.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 13
Water
Connect to a suitable water supply making sure that the pipes are flushed out to remove all foreign bodies, i.e.
flux or solder. Customers operating a BX oven in a hard water area must ensure that an efficient water-softening
device protects the water supply to the equipment. It is the customers’ responsibility to install and maintain an
adequate water supply to the oven, which should comply with local water regulations.
The oven comes supplied with a one-metre flexible hose – ¾-inch BSP connections (both ends).
Water pressure requirements: 2 to 4 bar
Domestic pressure is usually within this parameter.
Water conditioning unit advised.
No drain is required (unless fitting a condenser).
Ventilation
It is the customers’ sole responsibility to arrange for adequate ventilation. It should be sufficient to ensure water
does not condense on or around the oven.
Allow a 50 mm gap at the sides and rear of this oven.
Chimneys and evacuation ducts fitted above mono ovens should be insulated.
Before use
In the interests of hygiene, we strongly recommend that, before using the oven for the first time, you wipe the
inside of the oven and all accessories thoroughly with a clean cloth soaked in warm soapy water. Although the
utmost care is taken during assembly and pre-delivery inspection, there is always a possibility of residue
contaminating the first bake if this is not done.
Ensure that the locking casters on the base unit (if supplied) are locked into position.
Safety
Review the safety information on page 10.
Allow sufficient space for the oven door to open fully and easy loading and unloading of product trays
without people coming in contact with hot surfaces.
Racks should be available to allow cooked products to cool safely.
Oven gloves should be available at all times.
Note
This Installation and Operating Manual is available in Adobe PDF format at www.monoequip.com.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
14 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
Ambient working temperatures
Ambient working temperatures for electrical components, such as solenoid switches, circuit breakers, and
motors, should not exceed 40 °C (115 °F). Manufacturers of these, and other electrical components, advise
that any ambient temperature above 40 °C (115 °F) affects the functionality of the components, and any related
guarantees become void. For example, motors are not sufficiently cooled, contactor efficiency is seriously
impaired, and electronic components shut down.
It is the customers’ sole responsibility to arrange for adequate ventilation. Any component malfunctioning during
the guarantee period found to have been subject to excessive humidity or ambient working temperature above
40 °C (115 °F) will not be covered by the component manufacturer guarantee or MONO’s product warranty.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 15
5. Isolation
Electrical supply
To stop the oven in an emergency, switch off the electricity at the wall isolator.
Water supply
In an emergency, shut off the water supply to stacked ovens by closing the shut-off valves (Figure 4).
Figure 4: View of rear connections on a BX Eco-connect oven
Turn the appropriate valve 90° anti-clockwise () to turn off the water supply.
A. Top oven supply
B. Bottom oven supply
C. Supply from water filter

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
16 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
6. Touchscreen Operations
Operations are performed by touching an area of the screen, bringing up the next information panel or
activating a function.
Caution! Do not use excessive force to operate the touchscreen panel.
Figure 5: Main screen
Callout Function Purpose of the function
A Date It shows the current date.
B Time It shows the current time.
C Programs Access to saved baking recipe programs. Creation of programs.
D Multi Bake Creation of up to four simultaneous bakes with different timings.
E Settings Access to oven settings.
F Sleep Sleep mode – see page 32.
G Standby Standby mode – see page 32.
H 7-Day Timer Create an oven on/off schedule for every day of the week.
I Manual Bake Baking using manual controls.
J Favourites Easy selection of most frequently used baking recipe programs.
Note: The images are for illustration purposes and may differ from your oven.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 17
Starting and operating using ready-made recipes (programs)
1. Ensure the power and water supplies are safely connected to the oven (see Installation on page 11).
2. If the display (A) is blank, press the green power button (B) at the bottom of the front panel.
The oven goes through a boot-up sequence. Please wait.
Note
The images are for illustration purposes and may differ from your oven.
3. When a start-screen (wallpaper) appears, touch the screen anywhere to display the main screen.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
18 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
4. Touch the Programs tile on the Choose an option screen.
5. Select a product category.
(a) Touch the scroll up and down buttons to change category pages.
The Back button returns the display to show the Choose an option screen.
(b) Touch the tile of a product type you require (e.g., muffins).
A list of recipes then displays for that product type.
Note
Tiles typically show a product group image or a program number group, depending on how the oven was
factory configured. See the complete Installation and Operation Manual on www.monoequip.com for how to
do updates using the USB flash drive (if supported).
6. Select a baking recipe
(a) Touch the baking recipe required (e.g., blueberry muffins).
(b) If prompted, select Full Load or Half Load depending on the oven loading.

Installation and Operation Manual MONO Bx Eco-connect Ovens
FG0BX-UK-MAN-0200 | Rev. A21 (July 2021) MONO 19
7. A baking screen now appears.
(a) Wait while the oven heats up. A Heating message flashes on the screen.
(b) Load the oven with products when Ready flashes on the screen.
(c) Touch Start to begin baking.
Note
To maintain the heat in the oven, do not leave the door open for longer than needed. The actual oven
temperature fluctuates during a bake – this is normal and not an oven fault.

MONO Bx Eco-connect Ovens 4/5/10-Tray | Steam Installation and Operation Manual
20 MONO FG0BX-UK-MAN-0200 | Rev. A21 (July 2021)
8. During a bake, two actions can be performed.
Touch the View button to view settings during a bake.
Touch the numbered square (e.g., 2) to view the settings for different baking phases.
The Cancel button displays the baking screen again for the present baking phase.
Touch the Stop button to stop a bake at any time.
9. When a buzzer sounds to indicate the bake is complete, two actions can be performed:
Press the Stop button to finish the bake, or
Press the +2 mins to continue the bake for a further two minutes.
This time extension is adjustable in the Settings menu.
10. Remove the trays and close the door to preserve the heat.