Monster MH22003 User manual

CLARITY 101 PLUS
Model No.: MH22003
Quick Start Guide
Please read this Quick Start Guide carefully and keep it for future use.
Product Overview
Earphones (Left & Right)
Charging Case
SportClip™ x 1 Pair (Installed)
Eartips x 3 Pairs (S, M & L)
USB-C Charging Cable
Quick Start Guide & Warranty letter
1. SportClip™
2. Multi Function Button (MFB）
6
7

3. LED Indicator
4. Charging Contacts
5. Eartip
6. Charging Case - Charging Pin
7. Charging Case - Battery level LED Indicator
Power On/Off
The earphones will automatically turn on after removing from the charging case.
To turn off the earphones, put back to the charging case. Earphone’s light indicator is on and
starts charging, the earphones will automatically turn off. When the LED indicator is off, it is
fully charged.
Experiment with the different sizes of ear tip to find your perfect fit.
Twist the earphone until it fits securely and comfortably.
Pairing
Remove earphones from the charging case, the earphones will turn on automatically. Left and
right earphones will be connected automatically. Wait for a few seconds, “pairing” voice prompt
will be heard.
For new device connection, go to the Bluetooth settings on your mobile device and set it to
search for new devices (new Monster device). Once the earphone is paired, you will hear
“connected”.

Volume Control
To decrease/increase the volume level, quickly double press the MFB on the left/right
earphone during music streaming.
Calling
Short press the MFB to answer/end a phone call, long press the MFB about 2 seconds to
reject a phone call.
Music
Short press the MFB once to play/pause music. To play the previous/next song, press and
hold left/right MFB for around 2 seconds
Voice Control
After connecting to the phone, quickly triple press the MFB to activate the voice assistant.
Reset
Put the earphones back to the charging case, earphone’s light indicator will turn on to
indicate it starts charging. Then press and hold both left and right MFB at the same time
for around 5 seconds, when both light indicators flash three times, the reset process has
been successfully completed. Remove earphones from the charging case, the earphones
will turn on automatically. Left and right earphones will be connected automatically. Wait
for a few seconds, “pairing” voice prompt will be heard.
LED Indicator Guide
Status
Description
Voice Prompt
Power On
Blue LED indicator stays on about 1 second
“Power On”
Power Off
Blue LED indicator stays on about 1 second
“Power Off”
Pairing
Blue LED indicator flashes continuously
“Pairing”
Connected
LED indicator is off
“Connected”
Charging – Earphones
Blue LED indicator stays on
-
Charging – Charging
Case
Battery level LED Indicator flashes while
charging. When battery level LED indicator is
off, it is fully charged.
-

FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.