Monte Carlo Fan Company 3FSR52 series User manual

R
MonteCarloFans.com
3FSR52XXD Series Fan
UL Model No. : AC-552LF8700H
Total fan weight
with light kit READ AND SAVE
THESE INSTRUCTIONS
Si necesita asistencia en la instalación,
piezas de repuesto, o tiene preguntas
acerca de nuestra garantía, por favor
llame a nuestro centro de servicio
al cliente:
Si vous avez besoin d'aide pour l'installation,
des pièces de remplacement, ou si vous avez
des questions concernant notre garantie,
veuillez contacter notre service après-vente:
If you need installation
assistance, replacement parts,
or have questions regarding
our warranty, please call our
customer care center:
NEED HELP?
¿NECESITA AYUDA?
AVEZ-VOUS BESOIN D’AIDE?
Please do not return this product to the store.
Por favor no devulva este producto a la tienda.
Prière de ne pas retourner ce produit au magasin.
1-800-519-4092
MonteCarloFans.com
STOP ALTO
To register your fixture, please visit our website:
MonteCarloFans.com
shown with light
shown without light

1
Before you begin installing the fan, Switch
power off at Service panel and lock service
disconnecting means to prevent power
from being switched on accidentally. When
the service disconnecting means cannot
be locked, securely fasten a prominent
warning device, such as a tag, to the
service panel.
2
Before installing this fan make sure the
outlet box is properly installed to the house
structure. To reduce the risk of re, electric
shock, or personal injury, mount to outlet
box or supporting system acceptable for fan
support.
(Mounting must support at least 35 lbs.)
3
Remove preassembled hex nuts
from mounting plate. Save for
later use.
4
Thread safety cable through center
hole of the mounting plate. Thread
your house wires through center
hole also.These will be needed for
wiring of the fan.
5 6
Securely attached the mounting
plate to the outlet box using two
screws supplied by the outlet box.
Use metal outlet box suitable for fan
support (must support 35 lbs).
Safety instructions
Helpful Tools
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualied person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including re-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service
disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the oor to the trailing edge of the blade.
WARNING: To reduce the risk of re, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use
mounting screws provided with the outlet box (Mounting must support at least 35 lbs.)
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of re or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RY
manufactured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of re or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Lag screw
Lag screw
Washer
Lock washer
Safety cable
Safety cable
For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both
ush and downrod mode the safety cable must
be installed into the house structure beams
using the 3” lag screws provided. Make sure
that when the safety cable is fully extended
the leadwires are longer than the cable and no
stress is placed on the leadwires.

8
Carefully lift the fan motor assembly
and engage the slot in the motor
housing with the hook on the
mounting plate so that the motor is
securely suspended.
11
9
Lift the motor assembly up, aligning the
holes on the plate of motor assembly
with the screws on mounting plate.
Re-install the hex nut and washers
removed in step 3 to secure motor
assembly. Tighten all hex nuts securely.
Make wiring connections as indicated above.
White (Neutral) from house to white from remote
receiver marked AC N . Black (Live) from house to
Black from remote receiver marked AC L. Connect
all green ground wires to Grounded wire from
House.
12
10
Lift decorative housing to mounting
palet. Twist slots on decorative
housing into pins on mounting plate
clockwise to secure.
Make wire connections to power source using
wire nuts provided. Make sure that no liments
are outside of the wirenut. After making the wire
connections, the wires should be spread apart
with the grounded conductor and the equipment-
grounding conductor on one side of the outlet
box and ungrounded conductor on the other side
of the outlet box. The splices after being made
should be turned upward and pushed carefully up
into the outlet box.
13
Attach ywheel onto coupling on motor
assembly, aligning any of the 6 holes
on ywheel with the thread hole on the
coupling with arrow. Install 6 screws
provided to secure the ywheel. Tighten
all screws securely.
14
Insert blade into the slot on ywheel and install blade screws, ber washers
and enhance plate aligning each of the holes as shown. Repeat this process
for remaining blades.
Note: Make sure the side with a label “This side up” is installed upward.
Note: Make sure the holes on blade align with the alignment post on motor
assembly.
15
Loosen two and remove one
preassembled screw from the plate
on motor assembly. Keep screw for
later use.
16
Attach light pan onto the plate on
motor assembly, aligning its keyhole
slots with the screws on plate and
twist clockwise till lock. Re-install
the screw removed in step 15.
Tighten all screw securely.
17
Loosen two screws and remove one
screw from light pan. Save screw
for later use.
Pin
Slot
Alignment post Enhance plate
7
Set dip switches on the Remote Transmitter
and Remote Receiver to the same settings.
This must be done so the units will
communcate properly. If you have other fans
you can set to control from one transmitter
by setting both receivers the same as the
transmitter. If you have more than one fan
with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote transmitter dip switch
Remote receiver dip switch
Coupling
Flywheel
Receiver
Supply
circuit

23
Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready
A23 / GP 23A all 12V.Attach cover of remote
by placing over buttons and snap the battery
cover in place.
24
Place face plate over battery compartment
and buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over
4 pins and snapping into place.
25
Install wall control unit to outlet box
using machine screws provided.
26
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
20 21
Attach blanking plate by locating
dimples in light fixture with grooves in
the blanking plate and twist clockwise to
lock in place. WARNING:Make sure
light bulb is not installed when using
this cover.
Install 100-watt G9 base bulbs. Bulbs
included. WARNING: Over lamping the
fan will result in the fan lights shutting
down until the proper wattage of bulbs
are installed.Reset the lights by turning
off, replace bulbs with the correct
wattage bulbs, turn the power on.
Note: Do not replace bulb until it cools
down.
22
Attach the glass by locating dimples
in light fixture with groves in the
glass and twist clockwise until tight.
HAND HELD INSTALL WALL MOUNT INSTALL
For fan without light, go
to step 20
For fan with light, go to
step 21
19
Align keyslot holes of the light fixture
with the screws on light pan and twist
clockwise till tight. Install the screw
which removed in step 17. Tighten all
screws securely.
18
Connect white wire from fan to white
wire from light fixture, then connect
blue wire from fan to black wire from
light xture.

Remote Control Transmitter Features:
FORWARD/REVERSE Depress rev button allow a few seconds for
remote to change rotation direction with fan running.
LIGHT DIMMER To turn light on, press light dimmer once quickly. To
turn off press once quickly while light is on. To dim light hold down button
“light dimmer”. The light will cycle from bright to dim to bright until
button is released. Light will maintain last setting if turned off.
FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3
dots” for high. To turn fan off press square”.
FAN REVERSE (Press
once to change
direction of the fan)
Fan must be running
to reverse.
HIGH SPEED
MEDIUM SPEED
LED LIGHT
LOW SPEED
LIGHT ON/OFF SETTING
A N D D I M M E R ( P r e s s
and hold to dim light
innitively)
FA N O F F S E TT I N G
(Turns fan off only)

Trouble Shooting
If you have difculty operating your new ceiling fan, it may be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difculty in
installation, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.If this fan uses manual forward/reverse switch, make sure the switch is pushed rmly
either way. Fan will not operate when switch is in the middle.
4.If this fan uses remote controller, make sure dip switches are setting properly and make
sure battery is effective.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Check to be sure light bulb is tight in socket and not touching the glass shade.
5.Some fan motors are sensitive to signals from Solid State variable speed controls.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.If this is a downrod mount fan, make sure that the ridge of the canopy engages the
notch in the downrod ball.
2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to
ceiling junction box and junction box is mounted rmly to ceiling joist.
3.Check that all blades are screwed rmly into blade holders.
4.Check that all blade holders are tightened securely to motor.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance
from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade
is positioned for measurement. Repeat for each blade. If all blade levels are not equal,
you can adjust blade levels by the following procedure. To adjust a blade tip down, insert
a washer (not supplied) between the blade and blade holder at the screw closest to the
motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade
holder at the two screws farthest from the motor. Reverse the position of the washer if
blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulb and make sure bulb is tight in socket.
5.Remove light kit and check the plug connections if it is connected with plugs.
6.If this fan uses remote controller, make sure dip switches are setting properly and make
sure battery is effective.
CAUTION: Make sure main power is turned off before entering switch housing and/or
canopy.
WARNING: Over lamping the fan will result in the fan lights shutting down until the proper
wattage of bulbs are installed. Reset the lights by turning off, replace bulbs with the correct
wattage bulbs, Turn power on.
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. If fan does not start:
Trouble Suggested Remedy