Monte Carlo Fan Company 3VTR52/38 D Series User manual

R
MonteCarloFans.com
3VTR52/38XXD Series Fan
UL Model No. : 3VTR52/38
Total fan weight
with light kit READ AND SAVE
THESE INSTRUCTIONS
NEED HELP?
¿NECESITA AYUDA?
AVEZ-VOUS BESOIN D’AIDE?
Please do not return this product to the store.
Por favor no devulva este producto a la tienda.
Prière de ne pas retourner ce produit au magasin.
1-800-519-4092
If you need installation
assistance, replacement parts,
or have questions regarding our
warranty, please call our customer
care center:
Si necesita ayuda con la instalación,
partes de repuseto, o tiene preguntas
acerca de nuestra garantía, por
favor llame a nuestros asesores de
productos al:
Si vous avez besoin de pièces de
rechange, d ’aide pur l’installation ou si
vous avez des questions concernant notre
garantie, veuillez appeler nos conseillers
en produits au :
STOP ALTO
To register your fixture, please visit our website:
MonteCarloFans.com
shown with 52" blade
shown with 38" blade

1
Before you begin installing the fan, Switch
power off at Service panel and lock service
disconnecting means to prevent power
from being switched on accidentally. When
the service disconnecting means cannot
be locked, securely fasten a prominent
warning device, such as a tag, to the
service panel.
2
Before installing this fan make sure the
outlet box is properly installed to the house
structure. To reduce the risk of re, electric
shock, or personal injury, mount to outlet
box or supporting system acceptable for fan
support.
(Mounting must support at least 35 lbs.)
3
Remove the screw and lock
washer which near the J hook.
Keep them for later use, then
loosen the remainder 2 screws
from mounting plate.
4
Thread safety cable through center
hole of the mounting plate. Thread
your house wires through center
hole also.These will be needed for
wiring of the fan.
5 6
Securely attached the mounting
plate to the outlet box using two
screws supplied by the outlet box.
Use metal outlet box suitable for fan
support (must support 35 lbs).
Safety instructions
Helpful Tools
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualied person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including re-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service
disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the oor to the trailing edge of the blade.
WARNING: To reduce the risk of re, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use
mounting screws provided with the outlet box (Mounting must support at least 35 lbs.)
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of re or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RYK
manufactured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of re or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Lag screw
Lag screw
Washer
Lock washer
Safety cable
Safety cable
For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both
ush and downrod mode the safety cable must
be installed into the house structure beams
using the 3” lag screws provided. Make sure
that when the safety cable is fully extended
the leadwires are longer than the cable and no
stress is placed on the leadwires.
J hook

8
7
Attahced remote receiver onto the motor
plate with the double stick tape in the
hardware pack. Press firmly to position
the remote receiver as shown.
Set dip switches on the Remote Transmitter and
Remote Receiver to the same settings. This must
be done so the units will communicate properly.
If you have other fans you can set to control from
one transmitter by setting both receivers the
same as the transmitter. If you have more than
one fan with remote. You can set the dip switches
to different positions to have seperate control.
9
Carefully lift the fan motor assembly and
engage the slot in the motor housing with the
hook on the mounting plate so that the motor
is securely suspended.
10
Make wiring connections as indicated above.
White from fan to white from remote marked N.
Blue from fan to blue from remote marked light.
Black from fan to Black from remote marked L.
White from house to white from remote marked
AC N . Black from house to Black from remote
marked AC L. Connect all green ground wires to
Grounded wire from House.
11
Make wire connections to power source using
wire nuts provided. Make sure that no liments
are outside of the wirenut. After making the wire
connections, the wires should be spread apart
with the grounded conductor and the equipment-
grounding conductor on one side of the outlet
box and ungrounded conductor on the other side
of the outlet box. The splices after being made
should be turned upward and pushed carefully up
into the outlet box.
12
Lift the motor plate and aline its keyslot hole
with the screws on mounting plate and twist
clockwise to lock. Install the screw which
removed instep 3 to the mounting plate.
Tighten the screws securely.
13
Aline the clips on the housing with the
holes in the mounting plate
14
Lift motor housing up and turn motor
housing clockwise to hold in position.
15
52" and 38" blades included. Choose
the blade zise you like. Attach blade to
motor with 2 screws provided, only start
screw, do not tighten the screws yet.
Repeat for the other blades installation
then tighten all screws securely.
16
Loosen 2 screws and remove 1
screw from the motor plate. Save
the screw for later use.
17
Connect white wire from fan to white
wire from light xture, then connect the
blue wire from fan to the black wire from
light xture.
18
Aline keyslot holes of the light fixture
with the screws on motor plate and
twist ti to lock. Install the screw which
removed in step 16. Tighten all screws
securely.
Remote Receiver Dip
switches
Remote Transmitter
Dip switches

19
Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready
A23 / GP 23A all 12V.Attach cover of remote
by placing over buttons and snap the battery
cover in place.
20
Place face plate over battery compartment
and buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over
4 pins and snapping into place.
21
Install wall control unit to outlet box
using machine screws provided.
22
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
23
Attach blanking plate by locating
dimples in light xture with grooves
in the blanking plate and twist
clockwise.
24
Attach the GU24 18W CFL bulb and secure
by twisting clockwise. Bulb included.
WARNING: USE MAXIMUM GU24 18
WATTS LISTED SBCFL(SELF-BALLASTED
COMPACT FLUORESCENT LAMP) ONLY, NOT
USING SBCFL WILL OVERHEAT THE UNIT
AND CAUSE DAMAGE TO THE UNIT OR
THE FAN WHICH THE UNIT IS INSTALLED
TOGETHER.
25
Attach the glass by locating dimples
in light fixture with groves in the
glass and twist clockwise until tight.
HAND HELD INSTALL WALL MOUNT INSTALL
For fan without light, go
to step 23
For fan with light, go to
step 24

Remote Control Transmitter Features:
WARNING: This xture is not dimmable. Use only with on/off switch. Do
not use in conjunction fan/light remote controls or light dimmers.
FORWARD/REVERSE Depress rev button allow a few seconds for
remote to change rotation direction with fan running.
LIGHT ON/OFF To turn light on, press light button once quickly. To turn
off press once quickly while light is on.
FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3
dots” for high. To turn fan off press square”.
FAN REVERSE (Press
once to change
direction of the fan)
Fan must be running
to reverse.
HIGH SPEED
MEDIUM SPEED
LED LIGHT
LOW SPEED
LIGHT ON/OFF SETTING
(Press to turn on/off light)
F A N O F F S E T T I N G
(Turns fan off only)

Trouble Shooting
If you have difculty operating your new ceiling fan, it may be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difculty in
installation, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is rmly in up or down position. Fan will not operate
when switch is in the middle.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See
illustration in Step #6 of Downrod Mount installation).
2.Check that all blades are screwed rmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction
box and junction box is mounted rmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance
from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade
is positioned for measurement. Repeat for each blade. If all blade levels are not equal,
you can adjust blade levels by the following procedure. To adjust a blade tip down, insert
a washer (not supplied) between the blade and blade holder at the screw closest to the
motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade
holder at the two screws farthest from the motor. Reverse the position of the washer if
blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WARNING: USE MAXIMUM GU24 18 WATTS LISTED SBCFL(SELF-BALLASTED COMPACT
FLUORESCENT LAMP) ONLY, NOT USING SBCFL WILL OVERHEAT THE UNIT AND CAUSE
DAMAGE TO THE UNIT OR THE FAN WHICH THE UNIT IS INSTALLED TOGETHER.
CAUTION: Make sure main power is turned off before entering switch housing and/or
canopy.
User Servicing Instructions
WARNING: Before attempting to replace the fuse make sure the main power is turned off
to the fan. (Fuse is inside the canopy on the blue wire to remote receiver, push and twist
the cap to open the fuse case) Push and twist to reassemble fuse.
Risk of re. Replace fuse only with 3 amp, 125 volt fuse.
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. If fan does not start:
Trouble Suggested Remedy

Dec.31.09