Monte Carlo Fan Company 5UPR54 D Series User manual

Ceiling Fan Installation Instructions
For 5UPR54XXD Series Fans
READ AND SAVE THESE INSTRUCTIONS
Total fan weight
OWNER’S
MANUAL

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),
including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-
ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and
use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-
ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
Airflowdirection: warm weather-switch to left - forward / cool weather -switch to right - reverse
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
SAFETY TIPS
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
2
1
Installation
Use metal outlet box suitable for fan support
and use only the screws provided with the out-
let box (must support 35 lbs). Before attaching
fan to outlet box, ensure the outlet box is
securely fastened by at least two points to a
structural ceiling member ( a loose box will
cause the fan to wobble). Use only the
screws provided with the outlet box.
3
Place canopy on downrod. (as
shown)
4
Loosen the set screw in the yoke
cover.
5
Thread the canopy and yoke cover
onto the downrod.
6

Loosen the 2 set screws in yoke for
downrod to slip into yoke.
Insert downrod into yoke on top of
the Fan Body. Align the hole in the
Downrod with the hole in the Yoke.
Insert the Pin through the Yoke and
Downrod until the point appears on
the other side.
Install the Keeper Pin
789
Install the upper glass with screws
and fiber washers previously
removed. Tighten securely.
14
Place blade holders onto blades align-
ing holes in blade holder with holes in
blade. Make sure the side of the
blade you select is facing downward.
Install 3 screws and washers to back
side of blade as shown. Tighten
screws securely.Repeat this process 4
more times.
11
Remove 2 cardboards pre-installed
to the fan body. Rotate the center
flywheel so that the hole in flywheel
is facing opening of the upper light
kit plate. Insert the blade/blade arm
assembly into the flywheel hole and
tighten the screws securely. Repeat
4 more times.
12
Tighten the 2 set screws on yoke
once the downrod is installed in
place.
10
Remove and keep the 3 screws
and fiber washers pre-attached.
13
Thread the leadwires and safety
cable through the downrod.
16
Locate the yoke cover on the glass
and tighten the set screw on the
yoke.
17
Install 4 x 15 watt candelabra
base bulbs included.
15
Hang assembled fan from the mounting bracket
installed to ceiling in previous step. Make sure the
fan is hanging straight. Rotate fan until the tab on
the Mounting bracket engages the slot on the
Downrod Ball. This must be done to prevent the fan
body from rotating when the blades are in motion.
18

Place glass on fitter, install rubber
washer and hex nut to glass and
then tighten the finial nut securely
by hand.
30
Place the light fitter and tighten with
screws and washers.
28
Install 3 x 40 watt candelabra base
bulbs. Bulbs not included.
29
Remove the finial nut, hex-nut,
and washer from fitter.
25
Remove three screws and wash-
ers from light fitter.
26
Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture.
27
Lift canopy allowing the 2 studs
to protrude through the canopy
and install knurled nuts as shown.
Tighten the knurled nuts securely.
24
white
black
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Orange from fan to Orange from remote
marked Light/up. Blue from fan to blue from
remote marked down light. Black from fan to
Black from remote marked L. White from
house to white from remote marked AC N .
Black from house to Black from remote
marked AC L. Connect all green ground wires
to Ground wire from House.
orange
blue
Green
white
black
House
Fan
22
fuses
Make wire connections to power source using wire
nuts provided. Make sure that no filiments are out-
side of the wirenut. After making the wire connec-
tions, the wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box and
ungrounded conductor on the other side of the outlet
box. The splices after being made should be turned
upward and pushed carefully up into the outlet box.
23
For Canadian installation in both flush and downrod
mode the safety cable must be installed into the
house structure beams using the 3” lag screws pro-
vided. Make sure that when the safety cable is
fully extended the leadwires are longer than the
cable and no stress is placed on the leadwires.
19
Safety Cable
Lag Screw
Lag Screw
Washer
Lock Washer
Safety Cable
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans you
can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more than
one fan with remote. You can set the dip switches to different
positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
20
Install remote receiver into mounting
bracket.
21
Safety cable installation

Place face plate over battery compartment and
buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snapping into place.
33 HAND HELD INSTALL
Install wall control unit to outlet box
using machine screws provided.
34 WALL MOUNT INSTALL
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
35
Reverse function for this fan is a
switch on the top housing of the fan
body. Turn fan off and wait for fan to
stop then loosen the set screw of the
yoke cover and carry up the yoke
cover, then flip the switch to reverse
the direction of the blades.
31
Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready A23
/ GP 23A all 12V.Attach cover of remote by
placing over buttons and snap the battery cover
in place.
32

Remote Control Transmitter Features:
FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
HIGH SPEED
MEDIUM SPEED
LOW SPEED
FAN OFF SETTING
(Turns fan off only)
DOWNLIGHT ON/OFF
SETTING AND DIMMER
(Press and hold to dim
light infinitively)
LED LIGHT
UPLIGHT ON/OFF SET-
TING AND DIMMER
(Press and hold to dim
light infinitively)

1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when
switch is in the middle.
4.Make sure that shipping stabilizer tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing and/or
canopy.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are
finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibra-
tion persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as
an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls.
DO NOT USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after
this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration
in Step #14 of Downrod Mount installation).
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by select-
ing a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to
ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-
ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the
following procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade
and blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not
supplied) between the blade and blade holder at the two screws farthest from the motor. Reverse
the position of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-
ute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing and/ or
canopy.
WARNING: Before attempting to replace the fuse make sure the main power is turned off
to the fan. Replace only with a 3 amp fuse. (Fuse is inside the canopy on the blue and
orange wires to remote receive, push and twist the cap to open the fuse case).
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check
thisTroubleShooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call
our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten aprominent warning device, such as a tag, to the service panel.
Customer Service Center:
301 West Washington St.
Riverside, NJ 08075
1-800-519-4092
www.montecarlofans.com
Trouble Suggested Remedy