Monte Carlo Fan Company 5WF52XXD-L Series Fan Instruction manual

Owner’s Guide and Installation Manual
Attach sal s r c ipt to this card and r tain as your proof of purchas
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To r gist r your fixtur , pl as visit our w bsit www.mont carlofans.com
5WF52XXD-L Series Fan
Total fan w ight with light kit
UL Mod l No. : AC-552OD
8.4 kgs
18.48 lbs

© 2011 Mont Carlo Fan Company 12/30/2011
2
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO ERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! ead all instructions and safety information before installing your new fan. eview the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To educe The isk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and egulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not e-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, efrigeration and Air Conditioning Engineers (ASH AE) and the local code authorities.
CAUTION: To educe the isk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.
Note: Use only with light kits marked suitable for use in wet locations.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools equired for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Mont Carlo Fan Company 12/30/2011
3
Before you begin installing the fan, S witch
power off at Service panel and lock service dis -
connecting means to prevent power from being
switched on accidentally. When the service dis -
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet bo x is
properly installed to the house structure. T o reduce
the risk of fire, electric shock, or personal injury ,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet bo x is securley
fastened by at least two points to a structur al
ceiling member ( a loose bo x will cause the fan
to wabble). Use only the screws provided
with the outlet box.
3
21
Loosen set screws with locking nuts and
remove keeper from pin and then pin from
yoke for downrod (see inset).
Install downrod with canopy and yoke covers
into yoke. Align hole in downrod and y oke,
push pin through and replace k eeper. Tighten
set screws and locking nuts (see inset).
Hang assembled fan from the mounting br acket
installed to ceiling in previous steps. Mak e sure the
fan is hanging straight. Rotate fan until the tab on
the Mounting bracket engages the slot on the
Downrod Ball. This must be done to prev ent the fan
body from rotating when the blades are in motion.
Install downrod to canopy and then install yoke
cover to downrod. Thread wires and safet y
cable through downrod
56
8
4
Check the motor for plastic shipping sta -
bilizer tabs and remove them if they are
present.
7
For Canadian installation and for USA fan and light
kit ombinations over 35 lbs, in both flush and
downrod modes the safety able must be installed
into the house stru ture beams using 3” lag
s rews, washers and lo k washers provided. Make
sure that when the safety able is fully extended
the lead wires are longer than the able and no
stress is pla ed on the lead wires.
Note:If Installing The Se ondary Support Safety
Cable in the U.S., Do Not Remove Kno kouts In
The Outlet Box.
9Safety able installation
Safety Cable
Lag Screw
safety
able
3” lag
s rew
lo k
washer
washer

© 2011 Mont Carlo Fan Company 12/30/2011
4
Make wire connections to power source using wire
nuts provided. Make sure that no filiments are out -
side of the wirenut. After making the wire connec -
tions, the wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet bo x and
ungrounded conductor on the other side of the outlet
box.
11
Remove the 3 screws in round holes.
Remove cap by twisting and pulling
down. Save screws.
15
Attach blade brackets to blades
using the blade bracket screws
and washers provided.
13
The screws, washers, and motor
pads are pre-installed to the blade
holders. Attach blade assembly to
motor and tighten screws securely.
14
Connect black and blue wire from fan to Black or (Hot)
wire from house. Connect White wire from F an to
White (Neutral) wire from house. Connect Ground
leads from mounting bracket and downrod to Ground
lead from house. Refer to Safety Tips section of
manual.
10
House Fan
Blue
Black
White
Green
Black
White
Ground
Loosen one and remove one pre-
assembled screw from mounting
bracket. Save screw. Lift canopy up,
aligning its keyhole slot with the pre-
assembled screw on mounting
bracket and twist clockwise to lock in
place. Re-install the removed screw
and tighten all screws securely.
12
Tighen keeper nut onto threaded
pipe from the light kit.
Install keeper nut over lead wires.
17 18
Install switch housing to light kit b y
turning clockwise to tighten.
16

© 2011 Mont Carlo Fan Company 12/30/2011
5
Push glass up into fitter and hand
tighten the 3 screws to hold in place.
22
Locate blue and white wire from the fan
marked “For light kit”. Connect blue from fan
to black from light and white from fan to
white from light by pushing connectors
together.
Attach switch cap to fan b y lining up
3 screw holes and twisting cap clock -
wise. Then tighen the 3 screws.
19 20
Install 2 x 13 watt (E27) based
fluorescent bulbs.(Bulbs Included)
21

© 2011 Monte Carlo Fan Company 12/30/2011
6
1.Check main and branch circuit fuses or circuit break ers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. F an will not operate when
switch is in the middle.
4.Make sure that shipping stabiliz er tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not o ver tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not r attling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassw are are
finger tight. Check to be sure light bulb is tight in sock et and not touching glass shade(s). If vibr a-
tion persists from glass, remo ve glass and install a 1/4" wide rubber band on glass neck to act as an
insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitiv e to signals from Solid State v ariable speed controls. DO NOT USE a
Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this
period.
1.Make sure that the ridge of the canop y engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor .
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by selecting
a point on the ceiling abo ve the tip of one of the blades. Measure this distance from blade tip to ceil -
ng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measurement.
Repeat for each blade. If all blade lev els are not equal, you can adjust blade lev els by the following
procedure. To adjust a blade tip down, insert a w asher (not supplied) between the blade and blade
holder at the screw closest to the motor. To adjust a blade tip up , insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor . Reverse the position
of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can redistribute
the weight and possibly result in smoother oper ation.
1.Check blue wire from fan to mak e sure it is connected to hot wire from house
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
WARNING: USE MAXIMUM 13 WATTS LISTED SBCFL (SELF-BALLASTED
COMPACT FLUORESCENT LAMP) ONLY, NOT USING SBCFL WILL OVERHEAT THE UNIT AND
CAUSE DAMAGE TO THE UNIT OR THE FAN WHICH THE UNIT IS INSTALLED TOGETHER.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors ma y be mistaken for defects. If y ou experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty in installation, please call our
Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
Trou le Suggested Remedy
Warning: This fixture is not dimmable. Use only with on/off switch or
controllers. Do not use in conjunction fan/light dimmable remote
controllers or light dimmers.

Jun.2013 Update for CUL regulation