Monte Carlo Fan Company Centro Max 5CQM52-L Series Instruction manual

Owner’s Guide and Installation Manual
Total fan weight
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
Attach sales receipt to this card and retain as yourproof of purchase
To register your fixture, please visit our website www.montecarlofans.com
5CQM52XX-L Series Fan
UL Model NO. : AC-552AL
9.1 kgs
20 lbs

2
© 2015 Monte Carlo Fan Company 4/25/2015
Cautions and Warnings
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove
Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the
building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any unverified solid state fan speed control device, or
variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com

3
© 2015 Monte Carlo Fan Company 4/25/2015
ON
OFF
ON
OFF
Preparation
Warning: Before starting assembly of this product, please disconnect
power to area and familiarize yourself with the safety information
provided on page 2.
Determine mounting method to use.
A - Downrod Mount
B - Angle Mount
Important: If using the angle mount, check
to make sure the ceiling angle is not steeper
than 18º.
Important: If using the angle mount, make sure open end of mounting
bracket is installed facing the higher point of the ceiling.
C - Flushmount
Note: Flushmount is not available with vaulted ceiling.
Installation Instruction
Before you begin installing the fan, Switch power off at Service panel
and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a warning device, such as a tag, to the
service panel. (Fig. 1)
Before installing this fan make sure the outlet box is properly installed to
the house structure. To reduce the risk of fire, electric shock, or
personal injury, mount to outlet box or supporting system acceptable
for fan support (Mounting must support at least 35 lbs). (Fig. 2)
Use metal outlet box suitable for fan support and use only the screws
(and may be with flat washers and lock washers) provided with the outlet
box (must support 35 lbs). Before attaching fan to outlet box, ensure
the outlet box is securely fastened by at least two points to a structural
ceiling member (a loose box will cause the fan to wobble). Remove the
two outlet box screws provided with the box, aligning the holes of the
mounting bracket with the holes of the outlet box. Reinstall the 2 outlet
box screws securely. (Fig. 2-1)
A
B
C
Fig. 1
Fig. 2 Fig. 2-1
Mounting
bracket

4
© 2015 Monte Carlo Fan Company 4/25/2015
Installation Instruction (Downrod Mount)
Partially loosen downrod set screws from yoke at top of motor
assembly.
Remove keeper pin and cross pin from yoke, and save for later use.
Place downrod over canopy , canopy ring and yoke cover. Thread lead
wires and safety cable from motor assembly through downrod.
Slip downrod into motor housing yoke, aligning holes and install cross
pin and keeper pin.
Insert cross pin through yoke and downrod until point appears on the
other side, and insert keeper pin on cross pin.
Pull the downrod up tight against the cross pin, and then evenly tighten
the downrod set screws on motor housing yoke. (Fig. 3)
Warning: Cross pin and keeper pin must be installed securely, failure
to install them will result in serious injury.
Install 4 x 25 watt candelabra base bulbs (25W Max), Bulbs included.
(Fig. 3-1)
Install ball end of downrod into mounting bracket opening. Align
(engage) slot on ball with tab on mounting bracket.
Warning: Failure to align slot on ball with tab may result in serious
injury. (Fig. 4)
Fig. 3-1
Fig. 3
Fig. 4
Tab
Slot
Canopy
Lead wires and
Safety cable
Motor assembly
Cross pin Keeper pin
Yoke
Downrod
Set screw
Yoke cover
Canopy ring
Bulb

5
© 2015 Monte Carlo Fan Company 4/25/2015
Installation Instruction (Flushmount)
Remove canopy cover by turning counterclockwise. There are 6 holes
on the bottom of the canopy, 3 of them are larger. (Fig. 5)
Thread lead wires and safety cable through canopy. Place canopy over
yoke, aligning larger holes in canopy with the 3 existing screws on top
of motor housing. Install 3 screws and 3 lock washers (these screws
and lock washers are located in the hardware pack) into the remaining
holes. Tighten all screws securely. (Fig. 5-1)
To prepare the fan for wiring, hang fan onto mounting bracket by
sliding the canopy over the mounting bracket hook (Use one of
non-slotted holes on the rim of the canopy). (Fig. 5-2)
Safety Cable Installation
For Canadian installation and for USA fan and light kit combinations
over 35 lbs, in both flush and downrod modes the safety cable must
be installed into the house structure beams using 3” lag screws,
washers and lock washers provided. Make sure that when the safety
cable is fully extended the lead wires are longer than the cable and no
stress is placed on the lead wires. (Fig. 6)
Note: If Installing The Secondary Support Safety Cable in the U.S., Do Not
Remove Knockouts In The Outlet Box.
SAFETY CABLE INSTALLATION
Lag screw
Safety cable
Washer
Lock washer
Fig. 5-1
Fig. 6
Fig. 5-2
yoke
Canopy
Screws
Canopy
Hook
Lead wires and
Safety cable
Fig. 5
Canopy cover
Canopy ring

6
© 2015 Monte Carlo Fan Company 4/25/2015
Wiring
Warning: Make sure main power is turned off before making
wiring.
Make wire connections as indicated. Connect Black, Blue
and Orange wire from fan to Black (Hot) wire from house.
Connect White wire from Fan to White (Neutral) wire from
house. Connect all green grounded wires from fan to
Grounded wire from House. Make sure that no filaments are
outside of the wire connectors. (Fig. 7)
For control of fan and light separately from wall location,
follow diagram as shown. (Fig. 7-1)
Note : A professional electrician is recommended for this
type of installation.
Note : Wrap each wire connector separately with electrical
tape as an extra safety measure.
Canopy Installation
Partially loosen 2 of the set screws on mounting bracket
corresponding to the slotted holes on the canopy upper ring.
Remove the other 2 set screws. Save screws.
Raise canopy to mounting bracket, aligning loosened screws
in mounting bracket with slotted holes in canopy. Twist
canopy to lock. Reinstall screws (with washers) that were
previously removed and then tighten all screw securely.
Lift the canopy ring up, aligning notch on canopy with the
raise areas inside of canopy ring and pop it onto the canopy.
(Fig. 8, Fig. 8-1)
Fig. 7
Fig. 8
Mounting bracket
Mounting bracket
Fig. 8-1
Canopy
Set screws
Canopy
Set screws
Canopy cover
Downrod mount
Flush mount
Canopy ring
Notch
Canopy ring
Wall Switch
White
White
Black
Black
Power
Line
Blue
Grounded/
Green
Orange
Power supply
Black
white Grounding/Green
Fan
Light Blue
Black
Wall controller
Wiring Option with Wall Controller
Fig. 7-1
Orange

© 2015 Monte Carlo Fan Company 4/25/2015
7
Fig. 9
Fig. 10 Fig. 10-1
Fig. 11
Reverse switch
Screws
Blade
Blades bracket
Screws
Washers
Set screws
Set screws
Install fan and light pull chains to preassembled pull chains on fan.
Pull chains provided. (Fig. 11)
Forward/Reverse switch setting
Setting the reverse switch on the left hand side will result in
downward airflow and setting the switch on the right hand side will
result in upward airflow.
Note: Reverse switch must be set either way completely. If the
reverse switch is set in the middle position, fan will not operate.
(Fig. 11)
Operation and Maintenance
Refer to operation and maintenance on the second page of parts
list.
Blade installation
Install blade bracket with blade by 3 blade screws and washers provided.
Tighten screws securely. Repeat this process for remaining blades. (Fig. 9)
Remove shipping stabilizers from motor assembly.
Install the blade assembly to motor using the preinstalled screws. Tighten
screws securely. Repeat this process for remaining blade assemblies. (Fig. 9)
Note: Tighten blade bracket screws twice a year.
Switch housing installation and wiring
Loosen 2 and remove one set screws from the plate on motor, keep screw.
Attached top switch housing onto the plate on motor, aligning its keyhole
slots with the set screws on the plate and twist clockwise until tight. Reinstall
the screw which is just removed and tighten all screws securely. (Fig.10)
Attach capacitor onto switch housing by preadhered double-sided foam tap
as shown.
Connect the plug from fan to the plug from switch housing, aligning the claps
and make sure plugs connected securely. (Fig. 10-1)
Remove 4 set screws from top switch housing, keep screws.
Align the long slot on top switch housing with the reverse switch on switch
housing, and then install the switch housing onto the fan with the 4 side
mount screws which were just removed.
Top switch housing
Switch housing
Capacitor
Capacitor
Plate on motor
Set screws
電容器
電容器
shipping stabilizers
Long slot
Reverse switch
Pull chain
Pull chain
電容器

8
© 2015 Monte Carlo Fan Company 4/25/2015
Trouble Shooting
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
installation, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
way. Fan will not operate when switch is in the middle.
4.If this fan uses remote controller, make sure dip switches are setting properly and make sure
battery is effective.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Check to be sure light bulb is tight in socket and not touching the glass shade.
5.Some fan motors are sensitive to signals from Solid State variable speed controls.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the notch in
the downrod ball.
2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to ceiling
4.Check that all blade holders are tightened securely to motor.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned
for measurement. Repeat for each blade. If all blade levels are not equal, you can adjust blade
levels by the following procedure. To adjust a blade tip down, insert a washer (not supplied)
between the blade and blade holder at the screw closest to the motor. To adjust a blade tip up,
insert washer (not supplied) between the blade and blade holder at the two screws farthest from
the motor. Reverse the position of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulb and make sure bulb is tight in socket.
5.Remove light kit and check the plug connections if they are present.
6.If this fan uses remote controller, make sure dip switches are setting properly and make sure
battery is effective.
CAUTION: Make sure main power is turned off before entering switch housing and/or canopy.
WARNING: Over lamping the fan will result in the fan lights shutting down until the proper
wattage of bulbs are installed. Reset the lights by turning off, replace bulbs with the correct
wattage bulbs, Turn power on.
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. If fan does not start:
Trouble Suggested Remedy

Apr.2015