Monte Carlo Fan Company 5BS52 Builder Supreme User manual

Page 1 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
92 QUALITY CEILING FANS
Total fan weight
with light kit in-
cluded.
For Builder Supreme Fans
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan Installation Instructions
OWNER’S
ANUAL

Page 2 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
123
TOOLS REQUIRED
Phillips Scre driver Wire Cutters Pliers Step Ladder
Unpack and inspect fan carefully to be
certain all contents are included. (See
exploded view parts list.)
Turn off power at breaker box to avoid
possible electrical shock.
Use outlet box suitable for fan support.
Secure outlet box directly to the building
structure using ceiling joist screws.
Outlet box must support 35 lbs.
4
Install mounting bracket to outlet box
in ceiling using the screws and
washers provided with the outlet box. 5
Feed motor lead wires through downrod/
canopy assembly and insert downrod into
motor yoke. Next, insert clevis pin through
yoke and downrod and secure with cotter
pin. (see inset) Tighten both yoke set
screws to further secure downrod. 6
Clevis
Pin Set
Screws
Cotter
Pin
Ridge Ball
Notch
Safety Tips
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
READ AND SAVE THESE INSTRUCTIONS
INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards(ANSI/NFPA 70-
1996), including fire-rated construction.
Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on
one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the
floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.
Use mounting screws provided with the outlet box. ( ounting must support at least 35 lbs.)
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
NEVER place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NEPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched
on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the
service panel.
Carefully lift fan assembly onto
mounting bracket. Rotate fan so that
the notch on the ball engages the ridge
in the mounting bracket. This will allow
hands-free wiring.

Page 3 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
4
Ball
Notch
A
5
Install mounting bracket to outlet box in
ceiling using the screws provided with the
outlet box and washers.
Ridge
Canadian Mounting System Insert
WARNING: MOUNT ONLY TO AN OUTL T BOX MARK D
ACC PTABL FOR FAN SUPPORT
All set screws must be checked and retightened where necessary before
installation.
Canadian Safety Tips
A. Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on
the ball engages the ridge in the
mounting bracket. This will allow hands-
free wiring. For wiring instructions please
refer to page 4 step #7.
3
2While the fan assembly is still on the
ground thread the safety cable through
the mounting bracket.
safety cable
mounting
bracket
1
plain
washer
safety cable
Set screw
3" lag
screw
Lift fan assembly and install the safety cable
directly to the building structure using the 3" lag
screw and plain washer provided. Before
proceeding to the next step make sure that the
cable is properly installed and will support
the fan weight. ake sure the screw
washer and safety cable are installed using
the order pictured above.
Feed motor lead wires through downrod/
canopy assembly and insert downrod into
motor yoke. Next, insert clevis pin through
yoke and downrod and secure with cotter
pin. (see inset) Tighten both yoke set
screws to further secure downrod.
Cotter
Pin
Clevis
Pin Set
Screws

Page 4 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
Note:
After installation, please refer to operation, maintenance and troubleshooting sections in this manual.
If your fan is packaged with a light kit or if you wish to install a separately purchased light kit,
please refer to the insert sheet titled: L
IGHT K IT I NSTALLATION
INSTALLATION
WIRING OPTION WITH WALL SPEED CONTROL
Wall
control
Light Switch
Fan Switch
8
For control of fan and optional light from
wall location, follow diagram above.
NOTE: A professional electrician is
recommended for this type of installation.
7
*ATTACH BLU WIR
ONLY I F ATTACHING
LIGHT KIT WITH FAN
*
Secure with
twist-lock wire
connectors
(included)
STANDARD WIRING OPTION
11
Fiber
Washers
12
Shipping
Stabilizer
Tab
9
Raise the canopy up and align the two
holes in the canopy with the two holes
in the hanger bracket. Secure with two
5/32 x 1/2" screws provided.
CO BO-BLADE
10
Combo-Blades feature two high quality
finishes on one blade. Select the one
that best complements your decor, or
change the style with just a flip of the
blade.
For pullchain controls, follow diagram above.
ake sure that all exposed wiring is secured
inside wire nuts. Note: Wires from house may
vary in color and may not include ground
wire. After wiring is conplete, gently
push wires into junction box with wire
nuts pointing upward.
Attach blade brackets to blades using
the blade bracket screws and washers
provided.
Remove plastic shipping stabilizer tabs from
motor, if present. The screws, washers and
motor pads are pre-installed to the blade
holders. Attach blade assembly to motor
by tightening first screw one turn, then
tighten second screw securely. Then, go
back and tighten first screw securely.

Page 5 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these
installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be
remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the number printed on your parts list
insert sheet.
TROUBLESHOOTING GUIDE
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: ake sure main power is turned off.
3. ake sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the
middle.
4. ake sure that shipping stabilizer tabs have been removed from motor (see installation step #11).
1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Check to make sure wire nut connectors in switch housing are not rattling against each other or against the
interior wall of the switch housing.
CAUTION: ake sure main power is turned off before entering switch housing.
4. If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight.
Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibration persists from
glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insulator. Replace glass
and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid
State variable speed control.
6. Allow "break-in" period of 24 hours. ost noises associated with a new fan will disappear after this period.
1. ake sure that the ridge of the mounting bracket engages the notch in the downrod ball. (See illustration in
Step #6 of Downrod ount installation).
2. Check that all blades are screwed firmly into blade holders.
3. Check that all blade holders are tightened securely to motor.
4. ake sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box
is mounted firmly to ceiling joist.
5. ost fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on
the ceiling above the tip of one of the blades. easure this distance as shown in Figure 1. Keeping measure
within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all
blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip
down, insert a washer (not supplied) between the blade and blade holder at the screw closest to the motor
(Figure 2). To adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the
two screws farthest from the motor (Figure 2).
6. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the
weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: ake sure main power is turned off before entering switch housing.
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
Touching
Ceiling
Figure 1
Blade Tip Down:
Blade Tip Up:
Fan Blade
Fan Blade
Figure 2
Blade Brackets
4. If light does not work:
SUGG ST D R M DY
TROUBL
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
CUSTO ER SERVICE CENTER:
2900 WEST SE INARY DR.
FORT WORTH, TEXAS 76133
1-800-519-4092

Page 6 – Builder Supreme-English CUL
© Copyright 1996, onte Carlo Fan Co.REV.1,12/14/01
9/18/98 REV. 0 CREATED ENGLISH CUL VERSION FOR BUILDERS SUPRE E
12/14/01 Rev.1 Changed to allow for preinstalled motor screws to blade holder. Changed customer service number