MOOVI EB203A User manual

1
CONTENT
NAME OF THE MAIN PART 2
SAFETY INSTRUCTIONS 3
FUNCTION STRUCTURE OF REMOTE CONTROL 4
RIDE PROCESS 5
PREPARATION STAGE 5
ADJUSTMENT STAGE 5
RIDING STAGE 5
PARKING STAGE
BATTERY & CHARGER 6
BATTERY 6
CHARGER 6
CHARGING INSTRUCTIONS 6
MAINTENANCE 7
LUBRICATE/CHECK 7
BATTERY 7
PLACE & DAILY CARE 7
SOLUTION TO THE GENERAL PROBLEMS 7
PRODUCT SPECIFICATIONS TABLE 8
QUALITYASSURANCE SCOPE 9

2
NAME OF THE MAIN PART
1. Driven wheel components 5. Power switch
2. Anti-slip mat or slip-resistant paper 6.Controller components
3. Maple board 7.Skateboard charging port
4. Active wheel components 8. Battery box components
EB203A
EB203B

3
SAFETY INSTRUCTIONS
1. This product is an adult electric skateboard that is intended for adults only (Electric is not
a toy and can not be used by children under the age of 14). Don’t carry others at the same
time.
2. Please wear a safety helmet and other safety shielding facilities.
3. Don’t ride your e-skateboard in an unsafe or illegal place.
4. Please practice first. Once your riding skills have been mastered, you can enjoy your
e-skateboard.
5. Avoid dangerous actions or ride the e-skateboard single handed.
6. Don’t ride your e-skateboard on uneven or poor roads.
7. Please try to avoid riding the e-skateboard in the evening.
8. Don’t ride your e-skateboard when temperature is below -5°C, higher than 60°C
9. Don’t ride the e-skateboard if there is oil or ice on the road.
10. Don’t ride the e-skateboard on water logging road or on rainy days to prevent damaging
the control unit, motors or batteries.
11. Under bad weather, such as rainy day, snowy day or windy conditions, please don’t ride
the e-skateboard on water logging road or on rainy days to avoid any unpredictable damage.
12. When the person is not on the skateboard, please pay attention to keep the remote
control off as much as possible to prevent unnecessary damage caused by mis-operating of
the remote control.

4
FUNCTION STRUCTURE OF REMOTE CONTROL
Power on/off: Long press the button “A”for power on; long press the button “A”
again for power off.
Forward/Backward: Push the button ”C”ahead for forward ; Push the button ”C”aback
for backward ;
Signal indicator:After successful matching between remote control and e-skateboard, both
remote control light indicator and e-skateboard light indicator is red .You can enjoy your
Moovi e-skateboard now.
Battery indicator - remote control: After turning on the remote control, press button A. If
remote control power is enough (that means the remote control battery last more than 1
hours), the indicate lamp is green; if remote control power is less than 25%(that means the
remote control battery can last about 1 hours), the indicate lamp is red; if remote control
power is about 5%(that means the remote control battery can last about 15 minutes), the
remote control has a vibration (vibrate 0.5 seconds, then 0.5 seconds intervals, vibrate again

5
0.5 seconds)
Battery indicator - e-skateboard: Press button A. One light is on that means e-skateboard
have 25% power. One light indicator flashes that means e-skateboard have 12.5% power.
For example: If power level is 62.5%~75%, the light indicator is “○●●●” , if e-skateboard
power is less than 12.5%,the skateboard has a vibration and it’s light indicator is
“○○○☉”.When voltage less than safety voltage, the e-skateboard will slow down. You
should brake as soon as possible at this moment.
Accelerate/brake control: The e-skateboard move forward when push ‘roller ’ahead;
The e-skateboard stop moving when push ‘roller’aback.
Gears shift: Click the button “B”for shifting gears. There have 3 gears: top gear,
medium gear, low gear .E-skateboard level indicate lamp take turns low gear , medium gear
and top gear. When the e-skateboard move, the indicate lamp is blinking.
USB charge port: This port is for charging remote control
RIDING OPERATION
STARTING
a. Choose a suitable terrain for riding your Moovi e-skateboard
b. Put the e-skateboard in its right place.
ADJUSTING
a. Turn on the remote control: Switch on the remote control (Remote control signal indicator
flashes that indicates the remote control is on.)
b. Turn on the e-skateboard: Switch on the skateboard. (When the power switch indicator
flashes, it indicates that the skateboard is turned on; Attention, after connection is done, the
communication indicator on remote control and the power switch indicator on skateboard
would turn from flashing to constantly lit after connection is done.)

6
c. Adjust remote control status: According to remote control exploded view, before
skating, you should transfer low gear, push ‘roller’and check that the e-skateboard is
working properly.
START MOVING:
a. Start skating: The user stand on the e-skateboard, foot in tandem. Push ’roller’ slowly
and go forward at low speed (Pay attention to: through control body balance to keep
e-skateboard direction),When you can skate very well, you can skate at high speed .
PARKING STAGE
a. Stop the e-skateboard: Push’roller’ slowly for braking to let e-skateboard slow down
until stop working（Pay attention: Once meets emergency case, the user can jump down
from e-skateboard directly)
BATTERY AND CHARGER
Each Moovi e-skateboard is equipped with a special lithium battery and dedicated charger.
Each Moovi e-skateboard and its accessories have a special number .Use the battery charger
specifically for that purpose when recharging. Do not use another brand of charger.

7
Other type of e-skateboards is also not suitable for charging with Moovi charger. If this
results in damage to the battery or charger or other components, the user assumes the
responsibility.
BATTERY
After purchasing the Moovi make sure to fully charge the battery before using it .If not used
for a long time, please charge once every 3 months . Please charge in time after riding long
time. Untimely charging for dead battery will shorten battery life, or even lead to invalid
battery.
CHARGER
Your special Moovi charger has an over-charge protection function, which will
automatically turn off the charger’s power when the battery is charged 100%.
Special circumstances such as water, collision and other factors due to impropriate usage,
which lead to battery and/or charger damage, are not covered under warranty.
CHARGING INSTRUCTIONS
1. Open the rubber plug to get access to the charging port. Insert the charger to the socket.
2. Plug the charger into the power outlet.
3. Charging light will turn on. Red---Not full; Green---Full.
MAINTENANCE
CHECK
Every three months(or when needed), Please check whether the skateboard in a good
condition. The fasten parts is loose or not. If loose , please tighten.

8
Remarks: Regular inspection is very important!!!
BATTERY
If not used for a long time, please charge the battery once every three months to maintain
the full power capacity.
PLACE AND DAILY CARE
Please do not put the skateboard under the hot sun , in the rain or other serious damp places
for a long time . Please keep the skateboard clean.
SOLUTION TO THE GENERAL PROBLEMS
CHECK LIST
When the products have such problems, please refer to the following ways to solve.
1. The e-skateboard can not move forward.

9
Reason: The remote control or e-skateboard is not power on.
Solution: Make sure both remote control and e-skateboard power button is on.
2. The electric skateboard can not move forward or remote control vibrates.
The reason: The skateboard is low in power
Solution: Charge the skateboard or remote control.
3. Brake failure or abnormal parameters
The reason: Parameter lost.
Solution: Contact your local dealer or the Moovi support team.
4．If problems consists, please contact the Moovi support.
PARAMETER LIST
PARAMETER
ITEM NO.
EB203A/B
PRODUCT SIZE
1066*295*127mm
CARDON SIZE
1145*190*355mm
WEIGHT
N.W. 8KG,G.W. 11.5KG

10
PRODUCT
PERFORMANCE
MAX LOAD
Canadian maple 150KG
MAX SPEED
36KM/H (Loaded with 80KG)
CLIMBING ABILITY
25°
SINGLE
ENDURANCE
DISTANCE
18-20km (5.2AH)
(wind,roads and temperatures are all affected)
BATTERY
PARAMETER
STANDARD
VOLTAGE
36V
TYPE OF
BATTERY
Li(Ni-Co-Mn)O2,18650 Steel sheel column
BATTERY
CAPACITY
5.2AH
MOTOR
PARAMETER
MOTER TYPE
DC permanent magnet brushless motor
RATED OUTPUT
POWER
2X250W
MAX NO-LOAD
SPEED
2000r/min
RATED VOLTAGE
36V
RATED TORQUE
5 N.m
CHARGER
PARAMETER
INPUT VOLTAGE
AC100～220V
CHARGING TIME
2-3H

11
GURANTEE
If have following problems during warranty period , please contact the Moovi support :
PARTS
Quality issues
Warranty
period
Service
content
Motor
The motor can’t work under normal
circumstances
1 year
FOC
Control
unit
Failure under normal circumstances
1 year
FOC
Battery
The battery can’t be charged or
discharged under normal circumstances
1 year
FOC
charger
The charger can’t be charged or
discharged under normal circumstances
1 year
FOC
Noted: Please follow the correct way t use our products.
We will not be responsible for any damage to parts caused by abnormal use.
Users will assume their own responsibility .Within the warranty period, product failure
or damage due to the following causes have no warranty.
1. If you don’t refer to the instructions for proper maintenance of your Moovi
e-skateboard.
2. Unauthorized replacement of other manufacturer’s or brands batteries, charger or
other parts
3. The improper use of the Moovi for other purposes, such as high-risk
performances , causing damage
4. Damage caused by disassembly or reloading
5. Traffic accidents or other damages due to a collision
6. Label or seal is damaged and the body or accessories code does not match

12
7. Damage caused by driving e-skateboard on an unsuitable roads
8. Any other abnormal damage caused by improper usage
9. Body number and controller or battery number doesn’t match
1)This device may not cause harmful interference.
2)This device must accept any interference received, including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television.
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of more of the following measures:
i）Reorient or relocate the receiving antenna.
ii）Increase the separation between the equipment and the receiver.
iii）Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.This device should be
installed and operated with a minimum distance of 5mm between the device and your body.