OnlyOne O-3 User manual

ONLYON BOARD
Onlyone Board–O-3&O-4User Manual
Onlyone Board(www.onlyoneboard.com)
Thank you for purchasing Our Onlyone Board, Onlyone skateboard is
committed to providing great experience at much more affordable
prices.
Please read through all the information within this guidebook before you
Start to ride your board.
Warning
Your board may disconnect with the remote controller at some time due
to the radio interference. Please be aware that you might risk injuries
each time you ride an electric skateboard. Make sure to read the
following instructions before you start a ride.
1, Read User Guidebook Before Ride;
2, Make Sure to Wear Helmet and Other Protection Kits;
3, Please Abide By Local Traffic Rules and Regulations;
4, Do Not Ride on Wet Roads or Surfaces;
5, Always Check and Make Sure All the Screws Are Tightened;
6, Always Check the Remote Controller’s Battery Level;
7, Avoid Riding Downhill whith high speed Unless you are an expert;
8, Do Not Always Rely on Brakes and always think ahead to brake the

ONLYON BOARD
Board when in high speed.
9，Do not downhill when fully charged.
Get to Know the Board
Get to Know the Remote

ONLYON BOARD
Note:
In the following circumstances(Not limited to below), the remote will
vibrate:
1, The board was adjusted from one speed mode to another;
2, The board battery runs low;
3, The board direction is switched;
4, The board disconnects with the remote;
5, The remote is turning off.
Charge the board
1, Connect the battery charger with the wall charging socket;
2,Plug in the socket and start charging the board;
3, When the board is charging, the charging brick will show red lights.
When the board is fully charged up, the red light turns green;
4, It is normal to have the charging brick very hot during the charging
process. It will cool down when it is fully charged up;
5, Please keep an eye on the board while it is charging. Do not charge it
while nobody’s home or everyone’s sleeping.
Turn on the Board & the Remote

ONLYON BOARD
1, Press the power button on the side of the enclosure. A red light will be
flashing. That means the board is on, but the remote is not yet on;
2, Long press the power button on the side of the remote for a few
seconds. Let go of the power button when the red lights are on;
3, When the the red light on the side of the enclosure stops flashing, that
means the board is connected with the remote. Usually your board and
your remote are all pre-paired up before leaving our factory. So after the
board and remote are all turned on, you are ready to go;
Turn off the Board & the Remote
1, The board will turn itself off after a 5 minutes if left without any move;
2, Long press the power button on the side of the enclosure to turn off
the board;
3, Long press the power button on the side of the remote to turn off the
remote
How to Pair Onlyoneboard with its Remote
1, Long press the power button on the side of the enclosure and the
power button on the remote at the same time for a few seconds;
2, Let go of those two power buttons when the signal button on the
remote flashes red lights and then you have the board and the remote
successfully paired up;

ONLYON BOARD
3, If customer still finds it difficult to pair up the board with the remote,
please do not hesitate to contact us at onlyoneboar[email protected]om.
How to Identity Battery Level
Board Battery Level
1, Make Sure Both Remote and Board are Turned On;
2, Press the power button on the remote and look at the board power
indicator. 4 red lights on means the board has 100% battery; 3 red lights
on means 75% battery left; 2 red lights on means 50% battery left; 1 red
light on means 25% battery left.
Remote Battery Level
1, Press the power button on the remote;
2, If the remote power indicator shows red light, it means the remote
has at most 25% battery and can be used for at most 1 hour.
3, If the remote power indicator shows green light, it means it has over
25% battery and can be used over one hour.
Changing Speed Modes
1, Make sure both the board and the remote are turned on;
2, Please let go of the throttle first and then press the speed switch
button under the power button;
3, Speeds are classified into slow mode, medium mode and fast mode by

ONLYON BOARD
its red light’s moving speed. Press the speed switch, if the red light on
the board power indicator moves the slowest, it means the board is set
on the slow mode. If it moves the fastest, it means the board is set on its
fastest mode.
How Braking Works
1, Let go of the throttle;
2, Pull Back the throttle to brake the board;
3, Make sure the braking process to be gradual and gentle. You don’t
want to brake the board abruptly in one pull.
Changing into Reverse Direction
1, Push up/ Pull down the forward/backward switch on the side of the
remote;
2, The remote will vibrate once, which means the the board is in reverse
direction now.
Maintenance
Always take a minute to check the board before and after a ride. Good
maintenance will get your board a longer life span.
1, Always avoid the wet or icy surfaces and puddles for the sake of the

ONLYON BOARD
bearings and the hub motors;
2, Always make sure the screws on the deck and hub motors are
perfectly tightened;
3, Always check the board and remote’s battery level;
4,Avoid high speed downhill riding when the board is fully charged up;
5, Remember to charge the board regularly even if you don’t use it for a
long time;
6, Don’t unscrew the enclosure unless you have to;
7, Check your bearings regularly. If necessary, get some replacement
bearings to change;
8, Use a slightly wet cloth to clean the board so that you can always ride
the board as new.