Morphy Richards IB75219 User manual

Heated Bedding
Please read and keep these instructions
getting the best from your
new heated bedding...
Safety
•For your safety, the in-built system in this product will
automatically shut off the power if it reaches a
temperature that is higher than considered comfortable.
It will also shut off automatically if any unsafe situation
should arise.
Washing instructions
•Before washing, detach the switch control and lead
from the blanket.
www.morphyrichards.com
11
0870 060 2616
1800 409089
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 1

2
Important safety
instructions
The use of any electrical appliance
requires the following of basic common
sense safety rules.
Primarily there is danger of injury or death
and secondly the danger of damage to the
appliance. These are indicated in the text by
the following two conventions:
WARNING: Danger to the person!
IMPORTANT: Damage to the appliance!
In addition we offer the following
essential safety advice.
Care instructions
•Examine frequently for any signs of wear
or damage to the blanket, switch or cord.
In case of damage or misuse, cease using
and contact the Morphy Richards
aftersales service helpline. (see page 7)
•During the summer, the blanket can be
used to air the mattress. To store, roll in a
towel and store in a dry place. Avoid
folding or creasing the blanket once
unpacked.
•Do not dry clean the blanket, follow
washing instructions on the label attached
to the blanket and the details that relate
to your blanket.
Personal safety
•Do not use with a helpless person, an
infant or a person insensitive to heat.
•Young children should be instructed on
how to operate the controls safely and
heat settings controlled by a parent or
guardian.
•Do not use a hot water bottle at the same
time as using the blanket.
Product safety
•Ensure the blanket is used in the manner
in which it is intended, either as an
overblanket or underblanket as
appropriate.
•If used on an adjustable bed, check the
blanket or cord cannot become trapped
or rucked.
•Ensure the product is correctly fitted to
the bed, following the instructions in this
booklet.
•Do not insert pins or any sharp objects
into the blanket.
•Do not tuck the heated part of material
under the mattress.
•Do not use if the blanket is wet.
•Avoid pressing creases or folds into the
blanket. Do not switch on if the blanket is
folded, creased or rucked.
•Do not use any lead, switch or cord other
than the one supplied with this blanket.
•Do not coil or lay the lead on the blanket.
•Not intended for medical use in hospitals.
All Morphy Richards heated blankets have been manufactured to the highest European
standards. This product has been comprehensively tested for all known safety situations, so
you can relax in the knowledge that it will provide warmth, comfort and peace of mind.
IMPORTANT INSTRUCTIONS
PLEASE READ CAREFULLY
AND RETAIN FOR
FUTURE USE
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 2

3
Electrical requirements
Check that the voltage on the rating
label of your appliance corresponds with
your house electricity supply which must be
A.C. (Alternating Current).
If the socket outlets in your home are not
suitable for the plug supplied with this
appliance, the plug should be removed and
the appropriate one fitted.
WARNING: The plug removed from
the mains lead, if severed, must be
destroyed as a plug with bared flexible
cord is hazardous if engaged into a live
socket outlet.
Should the fuse in the 13 amp plug
require changing, a 3 amp BS1362 fuse
must be fitted.
This appliance does not need to be
earthed. It is a double insulated product.
Before use
Before using this appliance ensure that
the voltage indicated on the product
corresponds with the mains voltage in your
home. If you are in any doubt about your
supply, ask your electrical dealer or local
electricity company.
WARNING: Do not attempt to use
the blanket with controls other than
those supplied with the unit as
referred to on the rating label attached
to the blanket.
Dual control models
Each side of the blanket has a
completely separate element and each is
supplied with its own independant mains
lead. A 13amp plug on each lead is
essential.
Do not connect both leads to one
13amp plug.
The two leads should preferably be
plugged into individual sockets. However, if
only one socket is accessible, then a dual
adaptor should be used.
WARNING: Only the electric blanket
should be connected to the dual
adaptor. If you are unsure, please
contact a qualified engineer.
It is quite normal for the switch to
become warm as the components encased
are part of the protection circuit.
Safeguard overheat
protection system
Activation
The system will remain dormant
indefinitely as long as the blanket is
operating in the normal temperature range.
If for any reason the blanket is operated in
an abnormal situation or condition which
would otherwise have induced a rapid
temperature rise high enough to constitute a
hazard, the OVERHEAT SYSTEM should
intervene by cutting off the supply current
before the temperature reaches the point at
which damage may occur.
In the event of the OVERHEAT SYSTEM
operating, the blanket will cease to function.
WARNING: No attempt should be
made to repair the blanket or have it
repaired locally and the switch
supplied must never be replaced since
the specialised components are not
generally available.
The fact that this blanket incorporates
the overheat system does not absolve the
user from observing these instructions.
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 3

Fitting instructions
Fitted underblanket with
elasticated corner tapes
1Place the mattress cover directly on the
mattress with the control switch end at
the head of the bed.
2Turn the elastic corners underneath the
mattress to secure in place (see diagram
A).
3Ensure all creases are smoothed out.
4
A
Switch control
Note: Braille markings are located on the
back of the switch.
Automatically switches
the blanket on 3 hrs
before you go
to bed
These three settings automatically turn
the heat off after the selected time
12 hours
3 hours
1 hour
Timer & 'Off'
selection slider
Blanket 'Off'
position
Heat setting
indicator
Red = High heat
Green = Low heat
Sleep button
Allows you to re-heat
the bed through the night
once a timer setting has
switched off.
Low heat setting
(ALL NIGHT)
Heat selection slider
High heat setting
(PRE-HEAT)
Power 'ON' light⁄
¤
‹
‚
·
fifl
›
‡
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 4

5
How to use
1Ensure the blanket is fitted to the bed
correctly.
2Plug the power lead into the closest
socket, using an extension lead if
needed to ensure that the lead is not
stretched.
Preheating the bed
1Turn the blanket on by setting one of the
timer off settings ⁄,‹or Â.
2Set the heat setting on the control switch
to maximum heat, the light indicator will
show a red light to indicate that the pre-
heating has been selected. Allow
approximately 10-20 minutes for a light
heat and a further 20-30 minutes for the
blanket to heat the bed thoroughly,
although this time may vary depending
on room temperature.
All night use
1Select the required timer off setting
⁄,‹or  hours.
2Set the heat setting on the control switch
to LOW heat, the heat setting indicator
will show a green light. This setting will
provide safe and comfortable heat to
sleep on all night.
WARNING: Always ensure that the
heat setting is moved to the OFF
position when you get up the next day.
Braille markings
•Braille markings are located on the back
of the switch to help identify the
direction of the heat level in the dark, or
if visually impaired.
•The highest heat level
pre-heat is identified by 3 raised nodules
mid level by 2 raised nodules
low level (all night) by 1 raised nodule
Sleep button
1Use this button to turn the heat on for 30
minutes when the timer has switched the
heat off.
2Press the central blue button once.
3The small light at the base of the switch
will flash to indicate that the sleep
function has been activated.
4After 30 minutes the light will stop
flashing and the heat will switch off.
•Note: This function will only operate if
the blanket is switched to a timer off
setting, which has reached the end of
the time period. It will not work if the
switch is at the OFF 'O' position.
Setting the timer
1To program the heat to turn on in 3
hours time, move the timer button to the
unfilled 3 symbol . Ensure that the
heat setting is set to pre-heat, maximum
heat level.
2When you get into bed, change the heat
level to low, all night level. The heat will
turn off after 9 hours, unless an
alternative timer off setting or the OFF
'O' position is selected.
3To program the heat to turn off after a
set number of hours, move the timer
button to the filled hour symbol ⁄‹Â.
For example, set to turn heat off after 1
hour, move the button to ⁄. Ensure that
the heat setting is set to a low, all night
level.
Note: The timer function will switch the
blanket off after the selected time.
Timer must be switched to the OFF
position before setting a further
time.
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 5

6
Washing instructions
WARNING: Before washing ensure
that you detach all the controls from
the blanket.
•Do NOT dry clean -
•Do NOT iron -
1Measure the blanket so it can be
stretched back to its original size whilst
wet.
2Only use in a washing machine with a
drum large enough to take the blanket
without forcing it in.
Machine washing
1Unplug the blanket from the power
socket.
2Disconnect the control switch and cord
from the blanket by lifting the locking
lever over the raised button and pull
apart. B
3Wash on the WOOL setting at 40˚C.
4Gently stretch the blanket back to it’s
original shape and size before line drying
WITHOUT using clothes pegs on the
wired area of the blanket. (See
instructions for tumble drying overleaf).
Hand washing
1Unplug the blanket from the power
socket.
2Disconnect the control switch and cord
from the blanket by lifting the locking
lever over the raised button and pull
apart. B
3Use a mild washing liquid or detergent
and lukewarm water.
4Immerse the blanket in the water and
allow to soak for 5-10 minutes.
5Squeeze the soapy water through the
fabric.
6Rinse the blanket thoroughly in cool
water, gently squeezing the fabric.
WARNING: Do not wring dry.
7Gently stretch the blanket back to its
original shape and size before line drying
WITHOUT using clothes pegs on the
wired area of the blanket.
Tumble drying
1Controls must be removed.
2Gently stretch the blanket back to its
original shape before drying.
3Tumble dry on the LOW heat setting,
following the manufacturers instructions
for the required drying time.
Note: The blanket must not be tumble
dried on the standard heat setting. If a low
setting is not available, follow instructions
for the drying under 'machine washing'
section.
40º
B
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 6

7
After sales service
If the blanket fails to operate, check the
following before returning:
1Ensure that the plug and socket have not
become disconnected.
2Check that the supply plug is correctly
connected to the flex.
3Check the supply fuse and the 3 amp
plug fuse if applicable.
For further help and advice, please
contact our Helpline.
Helpline
Should you need any advice on using
the product, please contact our helpline,
8:30 - 5:00 Mon - Thurs
8:30 - 4:00 Fri
Tel: [phone]
Alternatively, please write to Morphy
Richards Consumer Care or email us on:
customercar[email protected]
0870 060 2616
1800 409089
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 7

I1100M UK Rev 1 01/05
The After Sales Division
Registered address
Morphy Richards Ltd, Mexborough
South Yorkshire, England, S64 8AJ
Helpline (office hours)
UK 0870 060 2616
Republic of Ireland 1800 409089
Morphy Richards products are intended for
household use only
Morphy Richards has a policy of continuous
improvement in product quality and design.
The Company, therefore, reserves the right
to change the specification of its models at
any time.
Your three year
guarantee
It is important to retain the retailers
receipt as proof of purchase. Staple your
receipt to this back cover for future
reference.
Please quote the following information if
the product develops a fault. These numbers
can be found on the rating label attached to
the blanket.
Model no. Serial no.
All Morphy Richards products are
individually tested before leaving the factory.
In the unlikely event of any appliance proving
to be faulty within 28 days of purchase it
should be returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days and
within 36 months of original purchase, you
should contact the Helpline number quoting
Model number and Serial number on the
product, or write to Morphy Richards at the
address shown.
Subject to the exclusions set out below
(see Exclusions) the faulty appliance will then
be replaced and dispatched usually within 28
working days of receipt.
If for any reason this item is replaced
during the 3 year guarantee period, the
guarantee on the new item will be calculated
from original purchase date. Therefore it is
vital to retain your original till receipt or
invoice to indicate the date of initial
purchase.
To qualify for the 3 year guarantee the
appliance must have been used according to
the manufacturers instructions.
EXCLUSIONS
Morphy Richards shall not be liable to
replace the goods under the terms of the
guarantee where:
1The fault has been caused or is
attributable to accidental use, misuse,
negligent use or used contrary to the
manufacturers recommendations or where
the fault has been caused by power
surges or damage caused in transit.
2The appliance has been used on a voltage
supply other than that stamped on the
products.
3Where the appliance has been used for
hire purposes or non domestic use.
4Morphy Richards are not liable to carry
out any type of servicing work, under the
guarantee.
This guarantee does not confer any rights
other than those expressly set out above and
does not cover any claims for consequential
loss or damage. This guarantee is offered as
an additional benefit and does not affect your
statutory rights as a consumer.
•This guarantee is valid in the UK and
Ireland only.
Switch 11 1100 Rev 1 15/4/05 1:25 PM Page 8