Morphy Richards STORM LIGHT UPRIGHT VACUUM CLEANER - REV 3 User manual

SSttoorrmmLLiigghhttUUpprriigghhtt
VVaaccuuuummCClleeaanneerr
Please read and keep these instructions
Getting the best from your new cleaner...
Filters
It is important that the pleated filter is clicked clean each time the dust canister
is emptied to allow air through the appliance. Wash the pleated filter regularly in
warm water and allow to air dry.
Blockages
Check nozzles, tubes, hose and connectors for blockages.
Note: The floor nozzle hose can be released for inspection see page 7.
Adjustable height handle
You can adjust the handle height to suit different height users, for carrying and
for storage. Please see page 4 for details.
Safety cut-out
Both the suction and beater bar motors are protected by safety cut-outs.
See page 6 for more details. If these operate it is important to unplug
from the main supply before attempting any remedial action.
Allergy sufferers
See page 5 for emptying advice.
Brush bar switch off
IMPORTANT: THE ROTATING BRUSH BAR WILL AUTOMATICALLY STOP
WHEN THE CLEANER IS PUT INTO THE UPRIGHT POSITION.
VC73373 MUK Rev 3
For replacement parts, help with using your Morphy Richards product,
problems and lots more, contact us by phone or through our website.
UUKKHHeellpplliinnee::0088445500777777770000
IIrreellaanndd11880000440099111199
73373 rev3 10/1/08 14:51 Page 1

2
IMPORTANT
SAFETY
INSTRUCTIONS
The use of any electrical
appliance requires the
following common sense
safety rules.
Primarily there is danger of
injury or death and
secondly the danger of
damage to the appliance.
These are indicated in the
text by the following two
conventions:
WARNING: Danger to
the person!
IMPORTANT: Damage to
the appliance!
In addition we offer the
following safety advice.
Location
• Do not use or keep this
product outside.
• Do not store the appliance
near hot surfaces eg.
ovens or heating
appliances.
Mains lead
• Do not allow the mains
lead to become strained or
run this appliance over it.
• If the electrical cable
becomes damaged, the
cable assembly must be
replaced. Do not attempt
this task yourself, contact
the helpline number that is
found at the bottom of the
page.
Personal safety
• WARNING: Keep loose
clothing, hair, fingers
etc. away from the floor
nozzle whenever the
cleaner is connected to
the mains.
• WARNING: Only lift the
product by the handles
⁄and .
•WARNING: Disconnect
from the mains supply
before attempting to
clear any blockages or
accessing the floor
nozzle.
• Disconnect from the mains
supply before cleaning or
emptying the appliance.
• Never modify the cleaner in
any way.
• Never use in the presence
of explosive liquid or
vapours.
• Never pick up inflammable
or poisonous liquids such
as petrol, copier toner or
other volatile substances.
• Never pick up acids,
asbestos, asbestos dust or
other hazardous dusts.
• Never touch the plug or
cable with wet hands.
• Unprofessional repairs can
be dangerous for users.
• Use only Morphy Richards
spare parts and
accessories.
• The appliance must never
be left running
unsupervised.
• This appliance is intended
for domestic use only.
Misuse or use for
commercial or any other
purpose will render the
guarantee invalid.
• Always disconnect the
appliance from the mains
supply after use.
• This appliance is not
intended for use by
persons (including children)
with reduced physical,
sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been
given supervision or
instruction concerning use
of the appliance by a
person responsible for their
safety.
• To protect against fire,
electric shock and personal
injury, do not immerse
cord, plug or cleaner in
water or other liquid.
Product safety
• Never use the appliance
without the filters being
installed.
• Never use the appliance to
vacuum hot ashes, broken
glass, sharp objects or
liquids.
Children
• Children do not understand
the dangers associated
with operating electrical
appliances. Never allow
children to use this
appliance.
• Children should be
supervised to ensure that
they do not play with the
appliance, or stumble over
the power cord.
Electrical
requirements
Check that the voltage on
the rating plate of your
appliance corresponds with
your house electricity
supply which must be A.C.
(Alternating Current).
If the socket outlets in your
home are not suitable for
the plug supplied with this
appliance, the plug should
be removed and the
appropriate one fitted.
WARNING: The plug
removed from the
mains lead, if severed,
must be destroyed, as
a plug with a bared
flexible cord is
hazardous if engaged
into a live socket
outlet.
Should the fuse in the 13
amp plug require changing,
a 13 amp BS1362 fuse
must be fitted.
FFoorrAAddvviiccee,,SSppaarreessoorrAAcccceessssoorriieess,,tteell::0088445500777777770000((UUKK))oorr11880000440099111199((IIrreellaanndd))
73373 rev3 10/1/08 14:51 Page 2

FEATURES
⁄Adjustable handle
¤POWER ON/OFF PEDAL
‹BRUSH-BAR ON/OFF
PEDAL
›Canister release button
fiFilter cleaning dial
flCanister handle
‡Dust canister
·FOOT PAD FOR HANDLE
RELEASE
‚Exhaust filter grille
„Exhaust filter
‰Adjustable height trigger
ÂFloor nozzle
ÊClarity Window
Back
ÁFlexible hose
ËCord storage quick release
cleat
ÈHose connector
ÍHose connector inlet flap
ÎTube connector
ÏExtension tube location
ÌDusting brush location
ÓCrevice tool location
ÔFloor nozzle hose release
Carry handle
ÒAdjustable handle release
button
ÚCable clip
Accessories
ÛDusting brush
ÙCrevice tool
ıExtension tubes (x2)
Filter
ˆPleated filter
˜Central mesh filter
¯Motor protection filter
(beneath dust canister),
shown on page 6
˘Dust canister lid
◊Dust canister
⁄
¤
‹
›
fi
fl
‡
·
‚
Ë
‚
ÎÈ
Ó

‰
Ò
˘
3
Ï„
Á
fi
Ù
Â Ê Ô
Ú
Û
ˆ
ı
›
˜
Í
Ì
◊
˘
73373 rev3 10/1/08 14:51 Page 3

4
Assembly
WARNING: Do not plug in
the cleaner until it is
assembled.
1Carefully unpack all
components.
2Lift cleaner body to upright
position.
3Insert the handle, with the ‘D’
shape facing forward into the
hole on the top of the product.
Push down until it clicks.
NOTE: The handle may be
removed by lifting while
simultaneously pushing the
release button with a suitable
tool eg. a small screwdriver A.
The release button is located in
a hole at the rear of the product
just above the cable cleat.
Rotate the cable cleat
downwards for easier access.
Adjustable handle B
1The handle height can be
adjusted to suit different height
users or pushed fully down for
easier carrying and storage.
2Pull the adjustable height trigger
‰upwards whilst pulling the
handle upwards or pushing the
handle downwards depending
on the desired height.
3For carrying and storage pull
adjustable height trigger
upwards and push handle fully
down until it clicks into place.
OPERATING THE
APPLIANCE
Using on carpets
1Place cleaner in its upright
position.
2Release the mains cable by
turning the quick release cleat
Ëhalf-a-turn and extend the
cable fully.
3Plug the mains cable into the
mains socket.
4Adjust the handle to the required
height.
5Clip the cable into the cable clip
holder Úat the rear of the
handle.
6Place your foot on the foot pad
· on the floorhead whilst
pulling the handle towards you
to release the handle into the
cleaning position C.
7Press the power on/off switch
¤ D on the floorhead for the
main power. Then press the
brush-bar on/off switch ‹to
activate the brush-bar motor for
carpet cleaning.
IMPORTANT: To prevent
damage to carpets, never
leave the cleaner switched
on in one place for an
extended period.
IMPORTANT: The rotating
brush bar will automatically
stop when the cleaner is
put into the upright
position.
Using on hard floors
Follow steps 1-6 from the
instructions for ‘Using on
carpets.’
Press the brush bar on/off pedal
‹to turn the brush bar off.
Using the hose and
attachments
1Take the flexible hose Áout of
the storage holder.
2Pull down the hose connector
inlet flap Íand insert the hose
connector with its ‘mouth’
pointing upwards E. Push the
hose connector fully in such that
the flap latches on to the
connector.
3Add the required accessory
directly to the tube connector Í
or fit the extension tubes for
maximum reach.
4When removing the connector,
gently lower the flap slightly to
release the catch then withdraw
the connector.
C
B
A
E
Í
È
D
‹¤
‰
·
Â
FFoorrAAddvviiccee,,SSppaarreessoorrAAcccceessssoorriieess,,tteell::0088445500777777770000((UUKK))oorr11880000440099111199((IIrreellaanndd))
73373 rev3 10/1/08 14:51 Page 4

5
IMPORTANT: With the hose
connector fitted all of the
suction is directed to the
hose. Remove the
connector before returning
to general cleaning with the
floor nozzle Â.
Under furniture
cleaning F
The unique pivot point on this
product allows the whole head
to fit under low furniture for
better cleaning performance.
DUST CANISTER
Emptying
1Every time the dust canister is
emptied, rotate the filter
cleaning dial fiseveral times
clockwise before emptying G
(this will agitate the fine dust
between the filter pleats and
restore the air flow).
2Remove the dust canister from
the product by pressing the
canister release button › H.
3Turn the lid quarter-of-a-turn
anti-clockwise to unlock, lift off
the lid with the pleated filter I.
4Empty the canister into a
dustbin.
5Re-fit dust canister and push
back into position.
Allergy sufferers
When emptying any vacuum
cleaner, it is difficult to avoid
exposure to dust. To minimise
this risk, please ensure that you
encase the dust canister in a
large bag to empty it. Close the
bag as tightly as possible round
the dust canister. Remove the
dust canister and close the bag
as tightly and quickly as
possible and dispose of this
immediately. It is advisable to
wear disposable gloves and a
face mask while emptying the
cleaner. If at all possible, ask a
non allergy sufferer to empty the
dust canister when required.
FILTERS
Cleaning
To maintain suction the pleated
filter must be cleaned using the
cleaning dial each time the dust
canister is emptied. To clean,
turn the filter cleaning dial fi
clockwise several times G
before emptying.
Pleated filter
In addition to cleaning the
pleated filter with the cleaning
dial each time the dust canister
is emptied, it is recommended
to regularly remove and wash (or
thoroughly brush off) the pleated
filter.
To thoroughly clean the filter, it
can be washed in warm water
(no detergent). Leave the filter to
air dry. Ensure the filter is
thoroughly dry before refitting.
See ‘Cleaning the dust canister
filter assembly’ section for a
description of how to access
the pleated filter.
G
I
F
fi
›
H
73373 rev3 10/1/08 14:51 Page 5