Morphy Richards Ultralight bagless vacuum cleaner User manual

www.morphyrichards.com
Ultralight bagless vacuum cleaner
Please read and keep these
instructions
getting the best from
your new cleaner...
If your cleaner isn’t picking up as well as it should,
please check
• Dust canister
It is important to regularly empty the canister even if it does not
appear full.
• Filters
It is important that the pleated filter is shaken clean each time
the dust canister is emptied to allow air through the appliance.
Wash the canister filters regularly in warm water and allow to
air dry. A spare pleated filter is included.
• Blockages
Check the hose, tubes and tools for blockages
• Belt
Check and replace damaged or broken belt
• Height adjustment
The height adjustment only comes into effect when the handle is
released by the handle release pedal È.
73322 Rev 2 17/1/05 2:42 PM Page 1

Important safety
instructions
The use of any electrical appliance
requires the following of common sense
safety rules.
Primarily there is danger of personal
injury and secondly danger of damage to the
appliance and property. These are indicated
in the instructions text by the following two
conventions:
WARNING: Danger of personal injury
IMPORTANT: Damage to the appliance
In addition we offer the following
essential safety advice.
Location
•Do not use or keep this product outside
when it is raining.
•Do not store the appliance near hot
ovens or heating appliances.
Mains lead
•Do not allow the mains lead to become
strained or run this appliance over it.
•If the electrical cable becomes damaged
the complete cable assembly must be
replaced. Do not attempt this task
yourself, contact Morphy Richards using
the helpline number.
Children
•Children do not understand the dangers
associated with operating electrical
appliances. Never allow children to use
this appliance.
Other safety considerations
•Never use in the presence of explosive
liquids or vapours.
•Never pick up inflammable or poisonous
liquids such as petrol, copier toner, or
other volatile substances. Never pick up
acids, asbestos or asbestos dust.
•Never use the appliance without the
filters installed.
•Never use the appliance to vacuum hot
ashes, broken glass, sharp objects or
liquids.
•Never modify the cleaner in any way.
•Always disconnect the appliance from the
mains supply after use or prior to
cleaning or emptying.
•The appliance should never be left
running unsupervised.
•Repairs to electrical appliances are only
to be undertaken by trained personnel.
Unprofessional repairs can be dangerous
for users.
•Use only genuine Morphy Richards spare
parts and accessories
•Never over-extend the hose such that the
cleaner is pulled over. If the cleaner is
knocked over, switch off before
attempting to upright.
•Never pick the cleaner up by the floor
nozzle when connected to the mains, use
the carrying handle.
•WARNING: Keep loose clothing, hair,
fingers etc. away from the floor
nozzle whenever the cleaner is
connected to the mains.
•Disconnect from the mains supply before
attempting to clear blockages, clear the
brush or replace the belt.
Electrical
requirements
Check that the voltage on the rating plate
of your appliance corresponds with your
house electricity supply which must be A.C.
(Alternating Current).
If the socket outlets in your home are not
suitable for the plug supplied with this
appliance, the plug should be removed and
the appropriate one fitted.
WARNING: The plug removed from
the mains lead, if severed, must be
destroyed as a plug with bared flexible
cord is hazardous if engaged into a live
socket outlet.
Should the fuse in the 13 amp plug
require replacement, a BS1362 13 amp fuse
must be fitted.
2
73322 Rev 2 17/1/05 2:42 PM Page 2

Features
⁄Vari power slider (certain models only)
¤Front cover release
‹Removable front cover
›Exhaust filter grille
fiCarpet height adjustment knob
flFloor nozzle with powered brush
‡Upper handle
·Flexible hose
‚Cord storage with quick release cleat
„On/Off switch
‰Carrying handle
ÂNested extension tubes (2)
ÊCrevice nozzle
ÁFurniture brush
ËHose clip slot
ÈHandle release pedal
ÍHose connector
ÎDust canister release (shown page 5)
ÏDust canister lid
ÌPleated circular filter
ÓDust canister
ÔCentral mesh filter
Canister handle
ÒMotor protection filter (shown page 6)
ÚExhaust filter (page 6)
ÛBelt cover (shown page 7)
ÙBrush bar (page 7)
ıMotor shaft (shown page 7)
ˆBrush bar end caps (shown page 7)
˜Hose clip
¯Turbo nozzle
3
A
Accessories included Extension tubes
Crevice tool
Furniture brush
‡
·
Ë
fi
›
fl
‹
¤
‚
‰
„
Í
È
⁄
Î
Ï
Ì
Ô
Ó
Á
Ê
Â
˜
Â
¯
Ê
Á
73322 Rev 2 17/1/05 2:42 PM Page 3

Assembly B
WARNING: Do not plug in the cleaner
until it is assembled.
1Carefully unpack all components.
2Lift cleaner body to upright position.
3Remove the two screws that are already
attached to the body.
4From the rear of the cleaner, align the
handle with groove and slide into the
body. If necessary, use thumb and finger
pressure to slide handle into position.
5Fasten the handle with the two screws.
Floor nozzle height
adjustment C
Before using the cleaner the floor nozzle
height must be set to the correct height.
Choose the setting which most closely
matches your floor surface.
•Use the DEEP CARPET setting when
using the tools.
Note: The height adjustment only comes
into effect when the handle is released by
the handle release pedal È.
Variable power D
(Certain models only)
Slide the variable power control to the
right to increase the suction power or to the
left to decrease suction. This feature is most
useful when using the hose and accessories.
Use the minimum setting when vacuuming
delicate fabrics/curtains etc. When not using
the hose it is advisable to keep the variable
slider set to maximum.
Using on carpets
1Place cleaner in its upright position.
2Set the carpet height adjustment knob to
the desired position.
3Release the mains cable by revolving the
quick release cleat 1/2a turn and extend
the cable fully.
4Plug the cable into the mains socket.
5Step on the handle release pedal to
release the handle to the desired
position.
6Press the on/off button to the ‘on’
position.
IMPORTANT: To prevent damage to
carpets, never leave the cleaner switched on
in one place for an extended period.
•Never have the brushes set too low such
that the cleaner is hard to push.
Using attachments
Follow steps 1-4 (using on carpets) but
set the carpet height adjustment knob to
deep carpet setting.
5Remove the hose connector Ífrom the
rear of the cleaner. Lift the hose ·from
the top handle hook. Insert the hose clip
˜into the hose clip slot Ë.
4
B
DEEP CARPET HARD FLOOR
MEDIUM CARPET
TOOLS
C
min max
D
73322 Rev 2 17/1/05 2:42 PM Page 4

•Push the required attachment firmly onto
the end of the hose.
•If additional length is required, attach one
or both extension tubes.
6Switch on/off.
•IMPORTANT: Always fix the hose clip ˜
to the main body slot Ëwhen using the
hose and tools.
•Never over extend the hose such that the
cleaner is pulled over.
IMPORTANT: Turning the cleaner
sideways helps prevent the cleaner being
pulled along by the stretch hose.
Using & cleaning turbo nozzle
Attach the turbo nozzle to the hose end
for use on upholstery and stairs.
After use your turbo nozzle may become
clogged. Turn over the nozzle and pull away
any hairs or fibres. If they are tightly wound
around the brush carefully snip the fibres
with scissors, being careful not to damage
the brush bar, pull away from the brush bar
and dispose.
Emptying
Empty the dust canister regularly even if
it does not look full this will maintain the
performance.
1Remove the front cover by lifting the
cover release lever. E
2Lift-up the dust canister release and pull
the canister away from the main body.
3Take the canister to the dustbin.
4Turn the lid 1/4turn anti-clockwise to
unlock, lift off the lid with pleated filter Ì,
put to one side. F
5Lift out the central mesh filter Ôfrom the
dust canister G. Brush clean if
necessary.
6Empty out the dust canister Ó.
7Re-fit the central mesh filter.
8Shake the pleated filter to remove all
dust.
9Re-fit pleated filter with lid into the dust
canister and turn lid 1/4turn clockwise to
lock.
10Re-fit dust canister into cleaner and push
to lock into position. Then re-fit front
cover.
Safety cut-out
If the cleaner overheats a motor
protection thermostat will automatically
switch the motor off. If this happens, switch
the cleaner off, unplug from the power
supply and leave the cleaner to cool for
at least 30 minutes. Check the airways for
blockages, empty dust canister and clean
the filters before restarting.
5
E
F
Ì
Ó
Ï

Î
¤
‹
Ô
73322 Rev 2 17/1/05 2:42 PM Page 5