mothercare Travel System Car Seat Installation instructions

Travel System Car Seat
For infants up to 13 Kg (Group 0+)
IMPORTANT
Read carefully and keep for future reference.
EXTREME HAZARD: Parents should not under
any circumstances use this child restraint in a
passenger seat equipped with an air bag.
Conforms to
ECE R44.03
Universal

2
1Safety Warnings
KEEP THIS OWNER’S MANUAL ALWAYS WITH THE CAR SEAT. PROVISIONS
ARE MADE ON THE REAR OF THE SEAT SHELL.
PLEASE READ THOROUGHLY BEFORE COMMENCING INSTALLATION AS
AN INCORRECT INSTALLATION COULD BE DANGEROUS.
DO NOT USE THIS CHILD SEAT IN PASSENGER SEATS EQUIPPED WITH AIR
BAGS.
This child seat must only be installed in the rearward facing position. Do not use on
side facing or rear facing seats.
Never use this child seat without fastening the child’s harness correctly, and never
attempt to use it without fastening it into the car as described in these instructions.
It is most important that the car seat belt is correctly routed with the lap portion of
the belt through the guides marked with light blue arrows and the diagonal belt
through the guide marked with a dark blue arrow. Ensure the belt webbing is not
kinked.
The child seat must be tightened down on the upholstery as tight as possible
to ensure maximum protection – the recommended method is shown in these
instructions.
Do not add to or modify the seat in any way.

3
1Safety Warnings
It is recommended that this car seat should be changed when it has been
subjected to violent stresses in an accident or has become badly worn. Periodically
inspect the harness for wear, paying particular attention to the attachment points,
stitching and adjusting devices.
Do not leave your child unattended in the seat at any time.
The carrying handle must be in the correct raised position when used in the car.
Ensure that no part of the seat is trapped in a door or folding seat. If your car has a
folding rear seat, ensure that it is correctly latched in the upright position.
Car interiors can become very hot when in direct sunlight – it is therefore recom-
mended that the child seat is covered when not in use. This prevents components,
particularly those attached to the child seat, becoming hot and burning the child.
In the event of an emergency it is important that the child can be released quickly.
This means that the buckle is not fully tamperproof and so your child must be
taught never to play with the buckle.
Luggage and other heavy or sharp objects should be secured in the car. Loose
objects are liable to cause injury in the event of an accident.

4
2Getting To Know Your Child Seat
Shoulder
straps
Seat
cover
Crotch
strap
One pull
harness
release
Shoulder
strap slots Handle
Handle
release
button
Lap belt
hook
Harness buckle
One pull
harness adjustment
Hood
Front view
This seat is classified as Group 0+ and is suitable for children from birth to 13 Kg
(Birth to 12-15 months). A VELCRO©strap is attached to your pushchair to attach
your child seat securely to the pushchair. Please refer to your pushchair user guide.

5
2Getting To Know Your Child Seat
Hood
Pushchair
release
handle
Level
indicator
Pushchair
mountings
Metal plate
Centre
belt guide
Pushchair
attachment
latch
Rear view
Owner’s manual compartment

6
2Getting To Know Your Child Seat
• Certain models only •
Shoulder
pads
Buckle
pad
Apron
(Not to be used
while seat is in
vehicle.) Head
hugger

7
3The Type of Approved Seat Belt You Must Have
Your Mothercare child seat can only
be installed rearward facing using a
lap and diagonal seat belt in the front
or rear passenger seats of the car.
DO NOT USE THIS CHILD SEAT IN
PASSENGER SEATS EQUIPPED
WITH AIR BAGS.
Diagonal
section
Lap
section

8
4Legal Requirements
This child seat is approved to ECE R44.03 and is only suitable for use with
3 point lap and diagonal seat belts approved to UN/ECE Regulation No. 16
or other equivalent safety standards.
Front Seat
Anyone, especially children, travelling in the front seat of a car must be
properly restrained. Children under three years must use a suitable
approved restraint designed for their weight. DO NOT place rear-facing
child seat on front seat with airbag.
Rear Seat
All adults and children must use seat belts or child restraints where they
are fitted in the rear of a car and are available for use.
If the appropriate restraint is not available, children from 3 years must wear
an adult seat belt if available.

9
5Important Notes
Keep this user guide in a safe place where it can easily be found.
When child seats are not in use, it is recommended that they be fastened
into the car with a seat belt to avoid being thrown about in the event of an
accident.
In an emergency your child can be released quickly by pressing the red
button on the harness buckle.
Do not remove the polystyrene impact pad located between the seat shell
and the cover.
If you travel with passengers using both the front and rear seats, the lighter
occupants should be in the rear seats and the heavier occupants in the front
of the vehicle. When a child seat is in the front seat, the lighter passenger
should be behind the child.
Do not allow the child seat to come into contact with corrosive substances
e.g. battery acid or solvents.

10
6Adjusting The Handle
Squeeze handle release button on
both sides at bottom of handle to
alter handle position.
Rotate handle into one of three lock-
ing positions — carrying (1), rocking
or reclining (2) or sitting (3). Be sure
it locks into desired position and that
the release buttons pop out.
Always place handle in position (1)
when using the car seat in a vehicle.
Always place handle in the down
position when removing your baby
from the seat.
1
21
2
3

11
7Fastening & Adjusting the Harness
To open the harness:
if handle is up, move it to
a down position.
Press red button on
buckle to open harness.
1
Drape harness straps over
seat back. Place baby in
seat. (Make sure baby’s
back and bottom are flat
against seat.)
Incorrect
2
Correct

12
7The Harness — Fastening & Adjusting
Fit the two shoulder strap buckle parts
together. The shape of the shoulder strap
buckle parts prevents incorrect insertion.
Push the shoulder buckle parts into the
buckle. A positive click will be heard
indicating the buckle is secure. Check that
the buckle is secure by pulling the shoulder
straps and the crotch strap.
3
4

13
To tighten the harness, pull the harness
adjustment strap at the front of the seat.
DO NOT allow harness straps to become
twisted. Keep them flat against your baby’s
body.
CHECK that harness is snug. You should
not be able to insert more than two fingers
between the harness and your baby’s chest.
ALWAYS securely fasten the harness on
your baby, whether using the seat in a vehicle
or as a carrier.
NEVER let your baby ride in the car seat
with a loose harness, with the straps off the
shoulders, or without the harness buckled at
all. Your baby could be thrown out of the seat.
5
7The Harness — Fastening & Adjusting

14
As your child grows you will need to
move the shoulder straps to the higher
slots. The correct slots are those at or
below the height of your child’s
shoulders.
DO NOT use upper harness slots with
a small infant. The harness may not
securely hold a small baby in a crash.
6
7
Correct
Incorrect
7The Harness — Fastening & Adjusting

8
9
15
To change harness slots, first remove
your baby. Press the release button at
the front of the seat and pull on the
harness to slacken it.
Behind the seat, take the two shoulder
strap ends off the metal plate and pull
the ends of the straps through the slots
in the seat cover. Insert them into the
appropriate set of slots. Reassemble the
strap ends onto the plate.
7The Harness – Adjusting the Shoulder Height

16
The ends of the harness straps have two
loops.
For a smaller baby, use the lower
shoulder slots and the upper strap
loops.
For a larger baby, use the upper
shoulder slots and the end strap loops.
WARNING: Use extreme care in
threading the straps according to the
diagram. Pull on the straps to check
that the junction plate holds them
firmly. If the straps are not secure,
they will not protect your baby.
10
7The Harness – Adjusting the Shoulder Height
11

17
7The Harness – Adjusting the Shoulder Height
Do not leave the strap ends hanging
in front of the junction plate as
shown. A poor connection may not
be noticed.
Do not just thread the straps
through the junction plate openings.
They will slide out.
12

18
9Attaching the Head Hugger – (certain models only)
Some infants may need extra support
to keep their head and body in a
comfortable position. Your model may
include our specially designed head
support. To use the support, thread the
harness straps through the slots in the
head support cushion.
8The Rocking Feature
The seat features a curved base for
use as a rocker on a flat surface.
To put the seat in a non-rocking
position put the handle in position 3.
Never place the seat on a raised
surface whether rocking or not – it
could fall off.
Always do up the buckle.
1
2
3

19
10 Attaching the Apron – (certain models only)
WARNING: The seat apron is not
to be used while seat is in your
vehicle as it will obstruct access to
the buckle in an emergency.
Place apron on seat as shown.
Make sure apron is covering the edges
of your seat.
1
To secure apron to seat fasten the
VELCRO®together at the side of seat pad
and apron as shown. Repeat on other side.
2

20
11 Fitting Your Child Seat Into Your Car
IMPORTANT: Always use with
the handle in the up (carrying)
position when using the child
seat in a vehicle.
Pull the lap section of seat belt over
the child seat and under the two lap
belt hooks.
Place the shoulder belt around the
back of the child seat exactly as
shown, making sure it runs through
the centre guide on the back of the
seat and under the first notch (see
diagram).
Fasten the safety belt buckle.
1
Centre
guides
Notch
opposite
shoulder
belt origin
Belt
hooks
Shoulder
belt
Lap belt