mothercare Little Hampton User manual

little hampton
wardrobe
user guide
important!
retain for future reference –
read carefully

1 introdduccion1
1 important notes
Please take a few minutes to read this user guide.
Lay the parts out and compare to the PARTS CHECKLIST below. Do not discard any packaging until you are
sure that you have all the parts.
This furniture is provided with an anti-topple device for securing to a wall. Failure to use this could result in the
furniture toppling onto a child.
2 competent people are required to assemble this wardrobe.
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
12 shelf brackets
1 door handle
2 drawer handles
10 back panel plates
40 cross head screws 3 x 16mm
12 cross head screws 5.5 x 20mm
18 cross head screws 7 x 15mm
1
10 cross head screws 7 x 45mm
43 dowels
24 cams
24 cam screws
3 door hinges
3 hinge plates

1introdduccion
2parts checklist
5 domed head screws M4 x 25mm
1 strap
1 base
2 sides (left and right)
1 door
2 washers
1 base rail
1 top
1 centre panel
2 back panels
2

1introdduccion
2parts checklist
1
1
1
1
1
12
12
12
1
1 bottom shelf
2 hanging rails
2 drawer fronts
2 drawer backs
3 shelves
4 drawer sides
2 drawer bases
3
tools required:
1 allen key (provided) 1 cross head screw
driver

1 introduction introduccion
3assembly
Attach the hanging rail brackets to the
centre panel and the right hand side
using 12, 5.5 x 20mm screws.
Attach the hinge plates to the right hand
side using 12,7 x 15mm screws.
Attach the hinges to the door using 6,
7 x 15mm screws
attaching the hinges and hanging rail brackets
1
4
Insert 4, dowels in to ends of the base
rail.
Insert 2 cam screws in to the base rail
Insert 3 dowels in to the base
Insert 2 cams in to the base
Locate the base rail in to the
corresponding pre-drilled holes of the
base and firmly push together.
Lock the 2 cams in place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the base rail to the base
2

1 introduction introduccion
3assembly
Insert 4, dowels in to the bottom shelf
and the center panel
Insert 2 cam screws in to the center
panel
Insert 2 cams in to the bottom shelf
Locate the bottom shelf in to the
corresponding pre-drilled holes of the
center panel and firmly push together.
Lock the 2 cams in place using the
cross head screw driver by turning these
in a clockwise direction 180 degrees.
Locate the base in to the corresponding
pre-drilled holes of the center panel and
firmly push together.
Secure in place using 2, 7 x 45mm
screws using the Allen key provided.
attaching the center panel to the base and bottom shelf
3
5
Insert 6, dowels in to the bottom shelf
and the base.
Insert 4, dowels in to the top of the
sides.
Insert 6 cam screws in to the sides
Insert 6 cams in to the bottom shelf and
base.
Locate the sides in to the corresponding
pre-drilled holes of the bottom shelf and
base and firmly push together.
Lock the 6 cams in place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the sides
4

1 introduction introduccion
3assembly
Insert 6, dowels in to the sides and
center panel.
Insert 6 cam screws in to the top
Insert 6 cams in to the sides and center
panel.
Locate the top in to the corresponding
pre-drilled holes in the sides and center
panel. and firmly push together.
Lock the 6 cams in place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the top
5
6
Insert the 12 shelf brackets in to their
corresponding pre-drilled holes in the
side and center panel.
Place the 3 shelves on to the brackets
by locating the brackets in to their
corresponding pre-drilled holes on the
under-side of the shelves.
attaching the shelf brackets and shelves
6

1 introduction introduccion
3assembly
Attach the 2 back panels to the back of
the wardrobe using 36, 3 x 16mm cross
head screws and the 10 back panel
plates
attaching the back panels
7
7
Insert the hanging rails in to the hanging
rail brackets
attaching the hanging rails
8

1 introduction introduccion
3assembly
Attach the wardrobe door by sliding the
door hinges on to the hinge plates.
Secure the hinges in place by tightening
the locating screw on the hinge plate
using a cross head screw driver.
Picture 10
Attach the door handle to the wardrobe
doors using 1, M4 x 25mm domed head
screw.
The wardrobe door may require
adjustment to align correctly. The hinges
have an adjustment screw which when
turned clockwise allows the gap
between the door and the centre panel
to decrease. Turning the screw
anti-clockwise will increase the gap
between the door and the centre panel.
Make small adjustments and visibly
check the results and repeat on each
hinge until the doors are aligned
correctly.
attaching the door and door handles
9
8

1 introduction introduccion
3assembly
Insert 4, 8 x 36 dowels in to the drawers
backs.
Insert 2 dowels in to each of the drawer
sides.
Attach the drawer back to the drawer
sides by inserting the dowels in to their
pre-drilled holes and pushing firmly
together. Secure using 4, 7 x 45mm
screws tightening with the Allen key
provided.
Slide the drawer base along the grooves
and push firmly in to place. Secure using
2, 3 x 16mm head screws.
Insert 4 cam screws in to the drawer
front.Attach the drawer front by pushing
firmly the drawer base in the groove on
the drawer front. Align the dowels and
cam screws to their corresponding
pre- drilled holes and firmly in place.
Insert 4 cams in to their pre-drilled holes
and lock in place using the cross head
screw driver by turning these in a
clockwise direction 180 degrees.
Attach the handles to the drawers using 2
M4 x 25mm domed head screws for each
drawer.
Locate the drawers in the base unit by
carefully aligning the rear drawer runner
wheels on to the front runner wheels of
the base unit. Slide drawers in base.
assembling the drawers
10
9

1 introduction introduccion
3assembly
THE LITTLE HAMPTON WARDROBE IS
SUPPLIED WITH AN ANTI-TOPPLE
DEVICE THAT SECURES TO THE WALL.
FAILURE TO USE THIS COULD RESULT
IN THE FURNITURE TOPPLING OVER.
WE RECOMMEND THAT YOU USE THIS
SAFETY DEVICE.
Using 1, 4 x 16mm screw, 2 washers and
strap, fix to the rear of the wardobe as
indicated in the diagram using a cross
head screw driver.
The loose end of the strap requires fixing
to the wall where the furniture will be
positioned. Certain wall materials require
different types of mounting hardware
(e.g. plastic rawl plugs, plasterboard rawl
plugs). Select mounting hardware suitable
for the walls in your home. If you are
unsure what type of mounting hardware
required please consult your local DIY
store for advice.
Installation only to be carried out by a
competent person.
attaching the strap - optional:
11
10
1
4
care and safety
Periodically check all fittings to ensure that none have come loose.
The wardrobe must be set up on an even stable surface.
Clean your wardrobe using a damp cloth and drying with a soft cloth. Never clean with abrasives, chemical
cleaners or household polishes.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Take care when handling or moving the wardrobe. Careless handling can damage wooden furniture.
care and safety
5customer care
If you have a problem with this product or require replacement parts, please contact your nearest Mothercare
store or telephone the Mothercare customer care line on 08453 30 40 30.
Alternatively write to: Customer Care, Mothercare, Cherry Tree Road, Watford, Herts, WD24 6SH.
www.mothercare.com