8A 8B
ENEN
DIRECTION OF
DISPLAY ROTATION COURSE PROGRAMMING OF TWO MOTORS
Normal rotation - leaf 1 starts opening (normal speed)
Slow rotation - leaf 1 goes into opening slowdown (slowdown speed)
Normal rotation – leaf 1 stops and leaf 2 starts opening (normal speed)
Slow rotation - leaf 2 goes into opening slowdown (slowdown speed)
Normal rotation – leaf 2 stops and starts closing (normal speed)
Slow rotation - leaf 2 goes into closing speed (slowdown speed)
Normal rotation - leaf 2 stops and leaf 1 starts opening (normal speed)
Slow rotation - leaf 1 goes into closing slowdown (slowdown speed)
DIRECTION OF
DISPLAY ROTATION COURSE PROGRAMMING OF ONE MOTOR PEDESTRIAN
Normal rotation - leaf starts opening (normal speed)
Slow rotation - the leaf goes into opening slowdown (slowdown speed)
Normal rotation - the leaf stops and starts closing (normal speed)
Slow rotation - the leaf goes into closing slowdown (slowdown speed)
01 • Press MENU for 2 sec. until it appears .
02 • Use UP until appears .
03 • Press Menu will appear . Use UP or DW to navigate the parameters.
04 • Press MENU to edit the chosen parameter value.
05 • The factory set time appears. Use UP and DW to change the value.
06 • Press MENU to save the new value.
COURSE PROGRAMMING
. PROGRAMMING "P"
You can use the remote instead of the MENU button.
Whenever a leaf touches a stop, wait 1 second before clicking on the MENU.
To exit the programming menus, press the UP and DOWN button simultaneously.
Whenever there is a reversal of the direction of travel, the preset deceleration time is
increased by 2 sec. up to 25 sec. maximum.
Course Manual Programming
This menu allows you to manually set the course of
the leaf/leaves.
Number of Motors
Allows you to define the number of motors connected
to the control board
(Default value NA) (Default value 02)
COURSE PROGRAMMING
FORCE ADJUSTMENT
DECELERATION TIME ADJUSTMENT
. PROGRAMMING "P"
. PROGRAMMING "P"
. PROGRAMMING "P"
This menu allows you to set the deceleration time of each leaf at opening and closing.
Slowing down on opening leaf 1
It allows to define the time that the gate will act with
slowdown in the opening.
Slowing down on closing leaf 1
It allows to define the time that the gate will act with
slowdown in the closing.
Slowing down on opening leaf 2
It allows to define the time that the gate will act with
slowdown in the opening.
Slowing down on closing leaf 2
It allows to define the time that the gate will act with
slowdown in the closing.
(Default value 3)
min. max.
0s
25s
This menu allows you to set the force that is injected into the motor when it moves at normal speed.
The default value is 4.
01 • Press MENU for 2 sec. until it appears .
02 • Use UP until appears .
03 • Press Menu will appear .
04 • Press MENU to edit value.
05 • The factory set time appears. Use UP and DW to change the value.
06 • Press MENU to save the new value.
Manual programming 2 arms:
01 • Press MENU for 2 sec. until appears.
02 • Press MENU once until appears.
03 • Press MENU (or remote control) to start programming the opening time of leaf 1.
04 • Press MENU to start the opening slowdown of leaf 1. Repeat these two steps (03 and
04) for leaf 2.
05 • Press MENU to start programming the closing time of leaf 2.
06 • Press MENU to start the closing slowdown of leaf 2. Repeat these two steps (05 and
06) for leaf 1.
07 • Press MENU once to display , leaf 1 stops.
08 • Use UP and DW to display to exit programming mode.
09 • Use UP and DW to stay in Standby.
Manual programming 1 arm:
01 • Press MENU for 2 sec. until appears.
02 • Press MENU once until appears.
03 • Press MENU (or remote control) to start programming the opening time of leaf.
04 • Press MENU to start the opening slowdown of the leaf.
05 • Press MENU to stop the leaf and start programming the closing time.
06 • Press MENU to start the closing slowdown of the leaf.
07 • Press MENU once to display , leaf 1 stops.
08 • Use UP and DW to display to exit programming mode.
09 • Use UP and DW to stay in Standby.
