ZIGBEE 612 User manual

SMART LED DRIVER
INPUT : 100-240VAC 0.40A 50/60Hz
OUTPUT : 24-38VDC Max 950mA
Max current can be set by app
SEC wire prep
0.5 -1.5mm² 
8 - 9mm
PRI wire prep.
0.75mm²
Class 2 Power Supply
N
L
W-
C-
V+
GND
0-10V+
0 - 10V Input
Output
AC In
SLC612 LED Lighting Driver
Dimming/CCT
Quick Start Guide

2
Introduction
1
The LED Lighting Driver allows you to remotely control your lightings as
well as automate using schedules.
This guide will provide you with an overview of the product and help you
get through the initial setup and installation.
SMART LED DRIVER
INPUT : 100-240VAC 0.40A 50/60Hz
OUTPUT : 24-38VDC Max 950mA
Max current can be set by app
SEC wire prep
0.5 -1.5mm² 
8 - 9mm
PRI wire prep.
0.75mm²
Class2 Power Supply
N
L
W-
C-
V+
GND
0-10V+
0 - 10V Input
Output
AC In
Get started
2
Warning!
• The LED Lighting Driver must be installed and serviced only by qualified
electrical personnel.
• Do not touch the terminals of the device during testing.
• Turn off all power supplying this equipment before installing.
• Make sure that the power supply is off before connecting or disconnecting
it to the auxiliary device.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors and covers before turning on power to this
equipment.
Failure to follow these instructions will result in death or serious injury.

3
2.1 To get started, you will need:
A ZigBee Gateway.
A mobile app.
2.2 Installation
The LED Lighting Driver must be installed by qualified electrical personnel,
keep the wiring diagram below for future reference.
C-
V+
W-
ACN
ACL
CCT Panel
C-
V+
ACN
ACL
SC Panel
SLC612 LED driver
SLC612 LED driver
SMART LED DRIVER
INPUT: 100-240VAC 0.40A 50/60Hz
OUTPUT: 24-38VDC Max 950mA
Maxcurrent can be set by app
SECwire prep
0.5-1.5mm² 
8- 9mm
PRIwire prep.
0.75mm²
Class2Power Supply
N
L
W-
C-
V+
GND
0-10V+
0- 10V Input
Output ACIn
SMART LED DRIVER
INPUT: 100-240VAC 0.40A 50/60Hz
OUTPUT: 24-38VDC Max 950mA
Maxcurrent can be set by app
SECwire prep
0.5-1.5mm² 
8- 9mm
PRIwire prep.
0.75mm²
Class2Power Supply
N
L
W-
C-
V+
GND
0-10V+
0- 10V Input
Output ACIn
Wiring Diagram

4
2.3 Connect to the gateway’s network
1. Set your gateway to permit joining.
2. The LED panel light connected to the LED Lighting Driver will flash 4
times and then become steady after installation, indicating it is ready to join
the gateway's network (reset it if not).
3. The LED Lighting Driver will join the gateway automatically and the
brightness of the LED panel light will drop to 50% when successfully joined.
4. Now you can control the LED Lighting Driver remotely from your mobile
app.
Note: If the LED Lighting Driver fails to join the gateway's network within a
minute, simply reset the LED Lighting Driver and retry.
Reset. Turn ON, and turn OFF. Repeat this action three times using a
physically connected power supply. The LED panel light will start flashing
when reset successfully. Repeat the process if you fail to reset the device.

5
3Technical Specifications
Wireless Connectivity • ZigBee 2.4GHz IEEE 802.15.4
RF Characteristics • Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m/30m
ZigBee Profile • ZigBee Lighting Link Profile
Power Input • 100-240 VAC 50/60 Hz
Output Current • 950mA MAX
Output Voltage • 24~38 V
Operation temperature • -40ºC - 60 ºC
Operation humidity • ≤85% (No condensation)
Dimensions • 118 x 74 x 32 (L) mm
Weight • 185g

6
Safety Notice
WARNING: Failure to follow these safety notices could result in fire,
electric shock, other injuries, or damage to the LED Lighting Driver and
other property. Read all the safety notices below before using the LED
Lighting Driver.
4
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to flammable liquids, gases or
other explosives.