Motormate Honda 10-401-SS User manual

Installation Instructions: Honda 10-401-SS
EPCO Products, Inc.
Fort Wayne, IN USA
1-844-MotorM8 (668-6768)
epcomarineproducts.com
The cover around the contact points could be damaged and/or cracked if instructions are not followed.
MotorMate is not responsible for any damage to the MotorMate unit or any part of the motor due to improper installation oruse.
Package Contents:1
4 5
2
3
RV:3062015
MADE IN THE USA Call 1-844-MotorM8(668-6768) for assistance with installation
(3.25") (7.19")
Reference Images:
(7.19")
(3.25")
A B
MotorMate Locking Pin.
Confirm Measurements Prior to Installation
It is necessary to confirm the spacing of the contact points on the
outboard motor are the same as A.
The motor yoke spacing A is the Center to Center distance
between the motor contact points securing the MotorMate to the
motor drive sha housing. See Reference Image A below.
The transom mount spacing B is measured between the inside
edges of the stern brackets. See Reference Image B below.
Raise motor and straighten
before engaging the MotorMate.
Clip Locking Pins into holes in
transom stern brackets.
Lower motor very slowly and stop one inch
away to make sure the MotorMate End Caps
are aligned with the contact points on the
motor.
Example of the recessed areas containing
the contact points where the MotorMate
End Caps secure the motor and where the
outboard motor center to center
measurements are made.
Continue lowering the motor while
aligning the MotorMate End Caps with the
contact points until the motor is securely
held in place.
Honda Installation Video: motormateusa.com
Measure between
center to center
distance between
the contact points.
Measure between
the inside edges of
the stern brackets.

LIMITED WARRANTY
EPCO Products, Inc., warrants the MotorMate
Outboard Motor Locking System to be free from
defects in materials or workmanship for the lifetime
of the MotorMate. This warranty is granted to the
original purchaser of the MotorMate unit. This warranty
does not cover any MotorMate unit that has been
modied in any way or if it is used with a motor for
which it was not originally designed nor specied.
This warranty does not cover damage, loss or failure
which results in whole or in part from improper
installation, misuse, neglect, failure to properly
maintain, or other damage caused by inappropriate
handling or use of, the MotorMate.
This warranty is limited to repair or replacement of
the defective MotorMate in the sole and exclusive
discretion of EPCO Products, Inc. This warranty does
not cover, and no claim shall be made hereunder
for, consequential damages, secondary charges,
incidental damages, labor, installation costs or ex-
penses, or losses or liability to third parties for personal
injury or property damage proximately resulting from de-
fects in the MotorMate. ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE AND ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, ARE EXCLUDED AND
DISCLAIMED, EXCEPTING ONLY THE EXPRESSED
WARRANTIES SPECIFICALLY SET FORTH IN THIS
LIMITED WARRANTY.
Breach or failure under the foregoing warranty shall not
be grounds to rescind any agreement under which the
MotorMate has been purchased or to claim set o or other
remedies against EPCO Products, Inc., or any other party
as a result of such breach or defect.
In order to make a claim under this warranty, the owner
of the MotorMate must provide written notice of specic
defects to EPCO Products, Inc., promptly, and in no event
more than thirty (30) days, after discovery of such defect.
The owner may return a defective MotorMate only upon
receipt of written return authorization from EPCO Products, Inc.
EPCO Products, Inc.
3736 Vanguard Drive - P.O. Box 9250
Fort Wayne, IN 46899-9250
1-844-MotorM8 (668-6768)
www.epcomarineproducts.com
RV3032015 Pat.
See Reverse For Installation Instructions
Installation Date:
Staple receipt to warranty for documentation purposes.
Purchased From: