Motorola MBP621-3 User manual

MODELS:
MBP621
MBP621-2
MBP621-3
MBP621-4
QUICK START GUIDE
For a full explanation of all features and instructions, please refer to the User’s Guide.
1. Setting up your Digital Video Baby Monitor
1. Insert the DC plug of
the power adapter
with the smaller DC
plug into the DC jack
on the side of the
baby unit, as shown.
2. Connect the other
end of the power
adapter to a suitable
electrical outlet.
A. Baby unit power supply
DC JACK
DC PLUG
B. Parent unit battery installation and power supply
Battery JACK
Battery PLUG
A rechargeable battery pack is supplied and should be
fitted, so that the parent unit can be carried to another
location without losing the link and picture from the
baby unit(s). Charge the parent unit before using it for
the first time or when the parent unit indicates that
battery is low.
1. Remove the belt clip/stand if it is attached to the
parent unit.
2. Slide off the battery compartment cover.
3. Insert the plug of the rechargeable battery pack into
the jack inside the battery compartment, and fit the
battery pack into the compartment.
4. Slide the battery compartment cover back until it
clicks into place, and re-attach the belt clip/stand.
5. Insert the DC plug of the power adapter with the
bigger DC plug into the DC jack on the side of the
parent unit.
6. Connect the other end of the power adapter to a
suitable electrical outlet.
7. The battery level indicator comes on.
1. The belt clip/stand attaches to the back of the parent unit and clips into the locking
slots on each side.
NOTE
It will only fit one way, as indicated by UP and the arrows on the inner side of the clip.
2. The unit comes with the accessory fitted in the belt clip position.
3. You can convert it into the desktop position by simply pulling the back part of the clip
out slightly and then rotating it by half a turn, as shown in the diagram on the left.
C. Belt clip/stand on parent unit
Belt clip position Desktop position
WARNING:
Strangulation Hazard. Children have
STRANGLED in cords. Keep this cord
out of the reach of children (more than
3ft (1m) away). Never use extension
cords with AC Adapters. Only use the
AC Adapters provided.

2. Basic explanation of the display icons
3. General Information
If your product is not working properly...
1. Read this Quick Start Guide or the User’s Guide.
2. Visit our website: www.motorola.com
3. Contact Customer Service:
Parent Unit
Connection status
displays when strong signal strength is detected between the baby unit and the parent unit.
, or displays when moderate signal strength is detected between the baby unit and the parent unit.
displays when the link between the baby unit and the parent unit is lost.
displays when the parent unit is searching for a baby unit.
Current view status Displays the number of the baby unit that is being viewed.
Zoom Displays when the camera on the baby unit is zoomed in.
Volume off Displays when the volume is turned off.
Sound activation
- You can turn Sound activation function ON or OFF. To check on your baby whenever there is sound in the baby’s room,
please turn it ON.
- Displays when sound activation is ON. When the baby unit detects a sound in the baby's room, the video image of the baby
will be displayed on the parent unit.
61oFCurrent
temperature Displays the current room temperature of the selected baby unit.
Battery status
scrolls when the battery is charging; displays when the battery is fully charged; displays when the
battery is low and needs charging; displays when you do not have a battery installed but operates using AC power, or the
battery has been installed incorrectly.
Camera selection You can select the baby unit you want to view, or view all baby units in Scan Mode.
Brightness You can change the brightness of the screen.
Sensitivity You can change the sound sensitivity level of the baby unit. The higher the sound sensitivity level, the more sensitive the baby unit
is in detecting sounds and transmitting them to the parent unit.
Pairing The system comes with baby unit(s) already paired with the parent unit. You can add or replace baby units.
US and Canada 1-888-331-3383
Email: [email protected]
Manufactured, distributed or sold by Binatone Electronics International LTD., official licensee for this
product. MOTOROLA and the Stylized M Logo, are trademarks or registered trademarks of Motorola
Trademark Holdings, LLC. and are used under license. All other trademarks are the property of their
respective owners.
© 2014 Motorola Mobility LLC. All rights reserved.
Printed in China
US_EN Version 7.0