Motorola AP6532 User manual

M
AP6532 Series Access Point
Installation Guide

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Sym-
bol is a registered trademark of Symbol Technologies, Inc. All other product or service names are
the property of their respective owners. © Motorola Solutions 2011. All rights reserved.

1 Introduction .......................................................................................... 1
1.1 Document Conventions .......................................................................................... 1
1.2 Warnings ................................................................................................................ 1
1.3 Site Preparation...................................................................................................... 2
1.4 AP6532 Package Contents ..................................................................................... 2
1.4.1 External Antenna Model Package Contents ............................................... 2
1.4.2 Integrated Antenna Model Package Contents............................................ 2
1.5 Features.................................................................................................................. 3
2 Hardware Installation ........................................................................ 4
2.1 Installation Instructions.......................................................................................... 4
2.2 Precautions............................................................................................................. 5
2.3 Access Point Placement ......................................................................................... 5
2.4 Integrated Antenna Model Wall Mount Instructions ............................................ 5
2.4.1 Wall Mount Hardware ................................................................................ 5
2.4.2 Wall Mount Procedure ................................................................................ 7
2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount Instructions ............ 9
2.5.1 Suspended Ceiling Mount Procedure.......................................................... 9
2.6 External Antenna Model Wall Mount Instructions.............................................. 10
2.6.1 Wall Mount Hardware .............................................................................. 10
2.6.2 Wall Mount Procedure .............................................................................. 11
2.7 External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions . 12
2.7.1 Suspended Ceiling Mount Hardware........................................................ 12
2.7.2 Ceiling Mount Procedure........................................................................... 13
2.8 AP6532 External Antenna Model Antenna Options............................................. 14
2.9 LED Indicators....................................................................................................... 15
Table of Contents

3 Defining a Basic Configuration ...................................................... 16
3.1 Using the Initial Setup Wizard ............................................................................. 16
4 Specifications.................................................................................... 37
4.1 AP6532 External Antenna Model Electrical Characteristics................................ 37
4.2 AP6532 External Antenna Model Physical Characteristics ................................. 37
4.3 AP6532 Integrated Antenna Model Electrical Characteristics ............................ 38
4.4 AP6532 Integrated Antenna Model Physical Characteristics.............................. 38
4.5 Radio Characteristics ........................................................................................... 39
5 Regulatory Information..................................................................... 40
5.1 Regulatory Information......................................................................................... 40
5.2 Wireless Device Country Approvals..................................................................... 40
5.2.1 Country Selection...................................................................................... 41
5.2.2 Frequency of Operation – FCC and IC ....................................................... 41
5.3 Health and Safety Recommendations.................................................................. 41
5.3.1 Warnings for Use of Wireless Devices..................................................... 41
5.3.2 Potentially Hazardous Atmospheres – Fixed Installations ....................... 41
5.3.3 Safety in Hospitals.................................................................................... 42
5.3.4 Pacemakers ............................................................................................... 42
5.3.5 Other Medical Devices.............................................................................. 42
5.4 RF Exposure Guidelines........................................................................................ 42
5.4.1 Safety Information..................................................................................... 42
5.5 International ......................................................................................................... 42
5.6 Europe................................................................................................................... 43
5.7 US and Canada..................................................................................................... 43
5.8 Power Supply........................................................................................................ 43
5.9 Radio Frequency Interference Requirements—FCC ............................................ 44
5.10 Radio Frequency Interference Requirements – Canada ................................... 44
5.10.1 Radio Transmitters.................................................................................. 44
5.11 CE Marking and European Economic Area (EEA) ............................................... 45

5.12 Statement of Compliance................................................................................... 45
5.13 Waste Electrical and Electronic Equipment (WEEE) .......................................... 46
5.14 TURKISH WEEE Statement of Compliance ........................................................ 47
5.15 Japan (VCCI) - Voluntary Control Council for Interference ................................ 47
5.16 Korea Warning Statement for Class B ITE......................................................... 48
5.17 Other Countries .................................................................................................. 48
5.17.1 Australia.................................................................................................. 48
5.17.2 Brazil........................................................................................................ 48
5.17.3 Chile ........................................................................................................ 48
5.17.4 China........................................................................................................ 49
5.17.5 Mexico..................................................................................................... 49
5.17.6 South Korea............................................................................................. 49
5.17.7Taiwan ..................................................................................................... 50
6 Motorola Solutions Enterprise Mobility Support Center ........... 51
6.1 Customer Support Web Sites............................................................................... 51
6.2 Manuals................................................................................................................ 51
7 AP6532 Series ROHS Compliance .................................................. 52

Introduction 1
1 Introduction
The AP6532 Access Point, a component of the Motorola Solutions Wireless Controller System, links
wireless 802.11a/b/g/n devices to the controller, enabling growth of your wireless network with a
costeffective alternative to standard Access Points. The AP6532 Access Point provides two
placement options: wall and ceiling. Wall mount slots fit onto two provided screws. Arrows on the
case guide the placement of the screws. For placement above a suspended ceiling, a safety wire tie
point on the case provides for a safety wire loop. The light pipe fits through a hole in the ceiling tile
to provide a view of the unit’s status lights.
The AP6532 Access Point receives all power and transfers data through the same CAT-5 or better
Ethernet cable. There is no additional power supply required. An 802.3af Ethernet switch or power
injector is required.
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
1.2 Warnings
• Read all installation instructions and site survey reports, and verify correct equipment
installation before connecting the AP6532 Access Point.
• Remove jewelry and watches before installing this equipment.
• Verify that the unit is grounded before connecting it to the power source.
• Verify that any device connected to this unit is properly wired and grounded.
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or
equipment malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
!

AP6532 Series Access Point: Installation Guide
2
• Verify there is adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications.
1.3 Site Preparation
• Consult your site survey and network analysis reports to determine specific equipment
placement, power drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Ensure adequate, dust-free ventilation to all installed equipment.
• Identify and prepare Ethernet and console port connections.
• Verify that cable lengths are within the maximum allowable distances for optimal signal
transmission.
1.4 AP6532 Package Contents
The AP6532 Access Point is available in integrated antenna and external antenna models. The
contents of the package differ between the integrated antenna and external antenna model.
1.4.1 External Antenna Model Package Contents
• AP6532 Access Point with external antenna connectors (Plenum Rated)
• Two wall mount screws
• Two wall anchors
• Light pipe
• Badge for light pipe
• AP6532 Installation Guide (This Guide)
1.4.2 Integrated Antenna Model Package Contents
• AP6532 Access Point with integrated antennas
• Two wall mount screws
• Two wall anchors
• AP6532 Installation Guide (This Guide)

Introduction 3
1.5 Features
• One RJ-45 connector
• LED indicators
• Safety wire tie point
• Slots for wall mounting
• Clips for mounting on a suspended ceiling T-bar
• Lock port for Kensington® style Security Lock
The AP6532 Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and
requires 802.3af-compliant power from an external source.
The AP6532 Access Point comes with dual radios both supporting 802.11a/b/g/n.
The Access Point contains runtime firmware which enables the unit to boot after a power up or
watchdog reset. The runtime firmware on the Access Point and the firmware downloaded from the
controller can be updated via the Ethernet interface from the Wireless Controller.
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.

AP6532 Series Access Point: Installation Guide
4
2 Hardware Installation
2.1 Installation Instructions
The AP6532 Access Point mounts either on a wall (with wide-shoulder screws) or on a suspended
ceiling T-bar. This unit is not designed for mounting on a desk.
To prepare for the installation, perform the following:
1. Match the model number on the purchase order with the model numbers in the packing list
and on the case of the device shipped.
2. Verify the contents of the box include the intended AP6532 Access Point and that the
included hardware matches the package contents on page 2.
3. Review site survey and network analysis reports to determine the location and mounting
position for the AP6532 Access Point.
Part Number Description
AP-6532-66030-US 802.11a/b/g/n dual radio integrated antenna configuration
United States model
AP-6532-66030-OUS 802.11a/b/g/n dual radio integrated antenna configuration
United States model for outdoor installation
AP-6532-66030-WW 802.11a/b/g/n dual radio integrated antenna configuration
World Wide model
AP-6532-66040-US 802.11a/b/g/n dual radio external antenna configuration
United States model
AP-6532-66040-OUS 802.11a/b/g/n dual radio external antenna configuration
United States model for outdoor installation
AP-6532-66040-WW 802.11a/b/g/n dual radio external antenna configuration
World Wide model
NOTE In the above part numbers, XX represents the 2-digit country code which
specifies which country the model is designed for. A country code of
“WW” represents a world wide model. The letter O preceding the 2-digit
country code specifies the model is designed for outdoor installation.

Hardware Installation 5
4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run the
cable to the installation site. Ensure there is sufficient slack on the cable to perform the
installation steps.
2.2 Precautions
Before installing an AP6532 model Access Point, verify the following:
• Motorola Solutions recommends you do not to install the AP6532 in wet or dusty areas.
• Verify the environment has a continuous temperature range between 0° C to 50° C.
2.3 Access Point Placement
For optimal performance, install the Access Point away from transformers, heavy-duty motors,
fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can
occur when metal, concrete, walls or floors block transmission. Install the Access Point in an open
area or add Access Points as needed to improve coverage.
Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright
enough. An area lit sharply might minimize coverage and create dark areas. Uniform antenna
placement in an area (like even placement of a light bulb) provides even, efficient coverage.
Place the Access Point using the following guidelines:
• Install the Access Point at an ideal height of 10 feet from the ground.
• Orient the Access Point antennas vertically for best reception.
To maximize the Access Point’s radio coverage area, Motorola Solutions recommends conducting a
site survey to define and document radio interference obstacles before installing the Access Point.
2.4 Integrated Antenna Model Wall Mount Instructions
This mounting requires hanging the AP6532 Access Point along its width or length using the two slots
on the bottom of the unit. The AP6532 can be mounted onto any plaster, wood, or cement wall surface
using the provided wall anchors. The following illustration displays a lengthwise mount.
2.4.1 Wall Mount Hardware
• Two wide-shoulder Phillips pan head self-tapping screws
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.

AP6532 Series Access Point: Installation Guide
6
• Two wall anchors
• Security cable (optional)
NOTE In the event that the original mounting screws are lost, the following
screws can be used instead: (ANSI Standard) #6-18 X 0.875in. Type A or
AB Self-Tapping Screw, or (ANSI Standard Metric) M3.5 X 0.6 X 20mm
Type D Self-Tapping Screw.

Hardware Installation 7
2.4.2 Wall Mount Procedure
1. Orient the case on the wall by its width or length.
CAUTION To ensure proper operation of the AP6532 Access Point, ensure it is
mounted in the correct orientation as shown above.
Integrated Antenna Wall Mount
Correct Orientation Incorrect Orientation
!

AP6532 Series Access Point: Installation Guide
8
2. Using the arrows on one edge of the case as guides, move the edge to the midline of the
mounting area and mark points on the midline for the screws.
3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall
mounting screw and stop when there is 1mm between the screw head and the wall.
4. If required, install and attach a security cable to the unit’s lock port.
5. Attach the Ethernet cable to the unit and to a controller with an 802.3af-compatible power
source.
6. Place the middle of each of the case’s mount slots over the screw heads.
7. Slide the case down along the mounting surface to hang the mount slots on the screw
heads.
8. Verify the unit has power by observing that the LEDs are lit or flashing.
NOTE When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.) if
the screws are going directly into the wall and 6mm (0.23in.) if the
provided wall anchors are being used.

Hardware Installation 9
2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount
Instructions
Ceiling mount requires holding the AP6532 Access Point up against a T-bar of a suspended ceiling
grid and twisting the case onto the T-bar.
2.5.1 Suspended Ceiling Mount Procedure
1. If required, install and attach a security cable to the unit’s lock port.
2. Plug the Ethernet cable into the unit and to a controller with an 802.3af compatible power
source.
3. Align the bottom of the T-bar with the back of the case.
4. Orient the case by its length, and the length of the T-bar.
5. Rotate the case 45 degrees clockwise, or about 10 o’clock.
6. Push the back of the case onto the bottom of the T-bar.
7. Rotate the case 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.
8. Verify the unit has power by observing the LEDs.

AP6532 Series Access Point: Installation Guide
10
2.6 External Antenna Model Wall Mount Instructions
Wall mounting requires hanging the AP6532 Access Point along its width or length using the pair of
slots on the bottom of the unit. The AP6532 can be mounted onto any plaster, wood, or cement wall
surface using the provided wall anchors. The following illustration shows a lengthwise mount.
2.6.1 Wall Mount Hardware
• Two wide-shoulder Phillips pan head self-tapping screws
• Two wall anchors
• Safety wire (recommended) and security cable (optional)
NOTE In the event the original mounting screws are lost, the following screws
can be used: (ANSI Standard) #6-18 X 0.875in. Type A or AB Self-Tapping
Screw, or (ANSI Standard Metric) M3.5 X 0.6 X 20mm Type D Self-
Tapping Screw.

Hardware Installation 11
2.6.2 Wall Mount Procedure
1. Orient the case on the wall by its width or length.
2. Using the arrows on one edge of the case as guides, move the edge to the midline of the
mounting area and mark points on the midline for the screws.
3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting
screw and stop when there is 1mm between the screw head and the wall.
4. If required, loop a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, around
the tie post and secure the loop.
5. If required, install and attach a security cable to the unit’s lock port.
NOTE The recommended hole size is 2.8mm (0.11in.) if the screws are going
directly into the wall, and 6mm (0.23in.) if the provided wall anchors are
being used.

AP6532 Series Access Point: Installation Guide
12
6. Place the large corner of each of the case’s mount slots over the screw heads.
7. Slide the case down along the mounting surface to hang the mount slots on the screw heads.
8. Attach appropriate antennas to the connectors.
9. Attach the Ethernet cable to the unit and to a controller with an 802.3af compatible power
source.
10. Verify the unit has power by observing that the LEDs are lit or flashing.
2.7 External Antenna Model Suspended Ceiling Tile (Plenum) Mount
Instructions
Ceiling mount requires placing the AP6532 Access Point above a suspended ceiling and installing the
provided light pipe for viewing the status lights of the unit.
This placement requires installation of the provided light pipe for viewing the status lights of the unit.
2.7.1 Suspended Ceiling Mount Hardware
• Light pipe
• Badge for light pipe
• Safety wire (recommended) and security cable (optional)
NOTE Notes or warnings about suspended ceiling mounts apply to all
installations where the unit is placed on suspended ceiling tile. The case
has a safety wire tie point for a standard safety wire.
CAUTION Motorola Solutions does not recommend mounting the AP6532
Access Point directly to any suspended ceiling tile with a thickness
less than 12.7mm (0.5in.) or a suspended ceiling tile with an
unsupported span greater than 660mm (26in.). Motorola Solutions
strongly recommends fitting the AP6532 Access Point with a safety
wire suitable for the specific installation. The safety wire should be a
standard ceiling suspension cable or equivalent steel wire between
1.59mm (.062in.) and 2.5mm (.10in.) in diameter.
!

Hardware Installation 13
2.7.2 Ceiling Mount Procedure
1. If possible, remove the ceiling tile from its frame and place it, finished side down, on a work
surface.
2. If required, install a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, in the
ceiling space.
3. If required, install and attach a security cable to the unit’s lock port.
4. Mark a point on the upper or unfinished side of the tile.
5. Push the light pipe through the tile at the mark and remove the light pipe. If necessary, use a
drill to make a hole in the tile.
6. Attach appropriate antennas to the connectors.
7. Snap the clips of the light pipe into the bottom of the case.
8. Fit the light pipe into hole in the tile from its unfinished side.
9. Attach any safety wire to the safety wire tie point or security cable to the unit’s lock port.
10. Bring the tile into the ceiling space.
11. Plug the Ethernet cable into the unit and to a controller with an 802.3af compatible power
source.
12. Verify the unit has power by observing the LEDs.
13. Place the ceiling tile back in its frame.
14. Snap the badge onto the light pipe from the finished side of the tile.
Badge
Ceiling Tile
Light Pipe

AP6532 Series Access Point: Installation Guide
14
2.8 AP6532 External Antenna Model Antenna Options
Motorola Solutions supports two antenna suites for AP6532 External Antenna models. One antenna
suite supporting the 2.4 GHz band and another antenna suite supporting the 5 GHz band. Select an
antenna model best suited to the intended operational environment of your Access Point.
The 2.4 GHz antenna suite includes the following models:
The 5 GHz antenna suite includes the following models:
For up-to-date information on supported antennas and antenna specifications, please see the
Motorola Enterprise Wireless LAN Antenna Specification Guide available on the Motorola Solutions
website.
Part Number Antenna Type
ML-2452-APA2-01 Dipole Antenna
ML-2499-SD3-01R Patch Antenna
ML-2499-HPA3-01R Omni Antenna
ML-2452-PNA5-01R Panel Antenna
ML-2452-PTA3M3-036 Omni Antenna
Part Number Antenna Type
ML-2452-APA2-01 Dipole Antenna
ML-5299-PTA1-01R Patch Antenna
ML-5299-HPA1-01R Omni Antenna
ML-2452-PNA5-01R Panel Antenna
ML-2452-PTA3M3-036 Omni Antenna

Hardware Installation 15
2.9 LED Indicators
Both Integrated Antenna and External Antenna models have LED activity indicators on the front of the
case. With the External Antenna models mounted above a ceiling, LEDs are at the center of an oval
badge on the ceiling; a light pipe enables viewing the back LEDs through the ceiling tile.
The LEDs provide a status display indicating error conditions, transmission, and network activity for
the 5 GHz 802.11a/n (amber) radio or the 2.4 GHz 802.11b/g/n (green) radio..
Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)
System Booting Solid On (During start up only) Solid On (During start up only)
Radio Shutdown
Administratively
or
LEDs Disabled
Off Off
Radio Not Configured
or
Country-code not set
or
WLAN not mapped to
radio
Blink (On 2 seconds, Off 2 seconds) Blink (On 2 seconds, Off 2 seconds)
Locate AP Mode Off Blinking