MotoTec MT-SKT-1600 User manual

1
Remote Controlled Electric Skateboard
OWNERS MANUAL
Instruction to the Remote Controlled Electric Skateboard
Dear Customer:
Congratulations and thank you for purchasing Electric Skateboard.For the greatest pleasure and
maximum use of your Electric Skateboard please read this manual thoroughly before your first test
ride.With proper use,your Electric Skateboard will prode safe,trouble free service in a long
term.Thorough understanding of the information in this manual is the first step in safety enjoying
your Electric Skateboard.
Preface:
Your Electric Skateboard is engineered and manufactured with the most technologically advanced
production methods and quality control processes;we inspect and test each Electric Skateboard
before shipment.

2
Tables of Contents
Contents Pages
Preface 1
Important safety information 2
Riding instructions 3
Maintaining your electric skateboard 4
Parts diagram of electric skateboard 5
1.Inspect outter carton for damages and report any to your freight carrier or dealer.
2.Open carton and inspect for internal damage,report any to your freight carrier or dealer.
3.Remove your new Electric Skateboard,remote controller and charger.
Important Safety information
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO OPERATE YOUR
ELECTRIC SKATEBOARD
The combination of power and weight make the Electric Skateboard a potentially hazardous
device.Improper use can result in proboble damage,serious injury or even death.Understanding all
of it’s features and controls is the key to safe riding.
Avoid uneven surfaces,potholes,surface cracks and obstacles.Always ride at a safe
speed,maintaining full control over the board at all times.Adult supervision is strongly
recommended.
NOT FOR CHILDREN UNDER 14.
Electric Skateboard SAFETY WARNING
The board does not conform to Motor Vehicles Standards and is not intended for operation on
public streets,roads or highways.Serious injury can result from unsafe operation of this
vehicle.The operation can minimize these assumed risks by wearing safety equipment.Always
check your local laws before using in public areas.
HELMETS,PROTECTIVE EYEWEAR,APPROPRIATE FOOTWEAR,WRIST,KNEE,AND
ELBOW PROTECTION MUST BE WORN AT ALL TIMES.DO NOT OPERATE THE
ELECTRIC SKATEBOARD IN TRAFFIC OR ON WET,FROZEN,AND ONLY OR UNPAVED
SURFACES OR NEAR PEOPLE OR OTHER VEHICLES.
OPERATION WARNING
This product is designed for use by children ages 14 and up.
Electric Skateboard maximum recommended weight for the rider is 250lbs.
This product should not be used without adult supervision.
The Electric Skateboard is designed for one rider only.
Be aware that radio signal interference could occur in your riding area.
The user of this product and the adult supervisor assumes all risks associated with it’s
use.To minimize these assumed risks,the user MUST WEAR SAFETY
HELMET,PROTECTIVE EYEWEAR,APPROPRIATE FOOTWEAR,KNEE AND
ELBOW PROTECTION AT ALL TIMES.

3
Do not operate your Electric Skateboard in crowded areas.
NOTE:IF YOU DO NOT UNDERSTAND ANY AND ALL PARTS OF THIS SAFETY
OPERATION INFORMATION,PLEASE CALL SKATEBOARD WARRANTY SERVICE
TO CLARIFYALL POINTS IN THIS OWNER’S MANUAL.
RIDING INSTRUCTIONS
Before riding your new Electric Skateboard,please be sure you fully understand how the
model you have purchased operates.
IMPORTANT
The Electric Skateboard wireless remote uses a unique close proximity low frequency radio
signal that minimizes the possibility of signal interference.Signal interference occur with
other Electric Skateboard using the same frequency,high power lines,cell phones or other
signal emitting devices.Use cautioin and check your ride area for signal interference before
use.
ELECTRIC SKATEBOARD
Power Hand Grip Controller
1. The Power Hand Grip Controller regulates the speed of the board.Pulling back on the
lever,the board will cause acceleration.Releasing the lever will return it to the neutral
position.Pushing forward on the lever will initiate braking force.
2. After standing on board,pull the power lever.Your Electric Skateboard will slowly and
build speed as you hold the lever back.
3. To decrease speed,let the lever go.This will slowly decrease your speed.To slow
quicker,push the lever forward to brake.Maximum speed and stopping distance depends
on your weight and riding surface.
4. Know your limits.Start slowly and keep your speed down until you have mastered
controlling your Electric Skateboard.
5. Read the section titled:”Riding your Electric Skateboard before attempting to ride.”
THROTTLE/BRAKE SAFETYWARNING
The Electric Skateboard is a powerful device,if you step on and pull the power lever,you
could be quickly(engaging the brake)could THROW YOU FORWARD FROM THE
BOARD.KNOW YOUR LIMITS AND USE THE POWER HAND GRIP CONTRROLLER
ACCORDINGLY.THESE IS A MOMENTARY TIME LAG FOR POWER AND BRAKE
ACTIVATION.
Hand Controller Battery
The hand controller uses a standard 9-volt alkaline battery.Switching the controller off when
not in use will maximize battery life.If you notice unreliable communication with the
board,the battery should be replaced.
Power Switch
The Electric Skateboard is equiped with an ‘ON/OFF’switch on the side of the battery box on
your board.To start the Electric Skateboard,turn the switch to the ‘ON’position.Make sure to
turn the board to the ‘OFF’position when not in use.Leaving the switch in the ‘ON position
when not in use may damage the electronics and battery.

4
Adjustments
Under normal use the Electric Skateboard requires no adjustments.However,it is prudent to
check all fasteners for tightness before every use.The bushings in the trucks are specially
formulated to provide shock absorption and positive steering control for the Electric
Skateboard
RIDINGYOUR ELECTRIC SKATEBOARD
BEFORE YOU RIDE
Be sure that you are thoroughly familiar with all of the features and controls discussed in the
previous section.All safety equipment should be worn,even when riding for short distances or
durations.Make sure that the area in which you plan to ride is paved,level,free of
obstacles,clear of power lines,radio antennas,and not crowded.
SAFETY WARNING
You are about to climb aboard a powerful motorized skateboard.If you have doubts about
your ability to ride,DO NOT RIDE IT!Know your limits and ride within them.Even if you
are an expert skateboarder,give yourself time to learn the Electric board and ride
conservatively,especially the first few times.Remember,the Electric Skateboard is silent and
others will not hear you coming.Give yourself adequate time to distance to stop and avoid
abstacles and others.
GESTTING STARTED
Make sure the switch to the Electric Skateboard is ‘ON’and the switch on the hand controller
is ‘OFF’.Step on to the skateboard and assume a normal skateboard stance(leaning
forward,knees slightly bent.)Keeping your fingers off the power lever,turn the switch on the
top of the controller to the ‘ON’position.Pull the lever for a moment to start the board.Start
off slowly by pulling the lever back until you become comfortable and in control of the speed.
Uphill and Downhill Riding
The Electric Skateboard is far superior to an ordinary skateboard in uphill and downhill
riding.On and uphill run,you will find that you need to keep your weight over the rear wheels
to keep them from slipping.If the hill is too steep,the board will bog down and continued use
may overheat the motor.Stop,step off and walk the steep hills.This board will take lighter
weight riders up hills faster and will slow down as the rider’s weight increases.
On downhill runs,the motor remains engaged at all times.Providing some drag to slow you
down.You also have full braking control.Frequent minor speed corrections with the brakes are
preferable to letting your speed build up and then braking suddenly.KNOW YOUR LIMITS
AND RIDE WITHIN THEM!

5
SPEED
NEVER RIDE DOWN HILLS THAT ARE TOO STEEP.TO MAINTAIN SAFE CONTROL
OF YOUR ELECTRIC SKATEBOARD NEVER RIDE DOWN HILLS THAT REQUIRE
CONSTANT BRAKING,AS IT CAN DAMAGE THE BOARD’S ELECTRONICS.
Turning your Electric Skateboard
The Electric Skateboard turns like any other skateboard.Apply pressure to the deck with your
heels or toes and the board will turn in that direction.More pressure will result in tighter
turns.In the hands of experienced rider,the Electric Skateboard is capable of making 10”
radius 180º turns.
Do not try to make turns at full speed.SLOW DOWN!
MAINTAININGYOUR ELECTRIC SKATEBOARD
MAINTENANCE WARNING
FAILURE TO FOLLOW MAINTENANCE INSTRUCTIONS AND GUIDELINES WILL VOID
YOUR WARRANTY.DO NOT OPEN BATTERY BOX!DOING SO WILL VOID YOUR
WARRANTY.
Routine Maintenance
Under normal use,your Electric Skateboard will require very little routine maintenance.Check
all fasteners for tightness before every use,especially if used on irregular surfaces.This will
require an allen wrench and a few different sized sockets or open-ended wrenhes.Your
Electric Skateboard is not waterproof and must not be ridden in the rain,mud,or other wet
areas to prevent electrical damage.Always keep your board clean and free of moisture.
Drive Wheel Replacement
It is normal for the drive wheel to wear faster than the other wheels.DRIVE WHEEL
REPLACEMENTS are available from Manufacturer or Dealer.
Drive Belt Replacement
Due to the superior design of the Electric Skateboard the drive belt will last a long time,but
eventually will wear out.Replacements can be ordered from Manufacturer or Dealer.
Wheel Replacement
As with any skateboard,the wheels of the Electric Skateboard will wear out with
use.Replacement wheels,bearings and spacers are available from Manufacturer or Dealer.
Rubber Bushing Replacement
Although specially formulated for extremely long life,the rubber bushings located in the
trucks of your Electric Skateboard will wear over time.It is recommended that they be
replaced with the same special bushings that are standard equipment on the board.They are
available through Manufacturer or Dealer.

6
Battery Maintenane
The rechargeable battery that powers your Elecctric Skateboard should last 1-2 years if kept
properly charged,but will slowly decrease in capacity and eventually fail to hold a charge.To
maintain maximum life,always keep your Electric Skateboard charged when storing for
extended periods of time.Plug in once a month to maintain a charge.They are easily
replaceable using the Battery Replacement Kit,which is available from Manufacturer or
Dealer.See diagram below.ALWAYS STORE YOUR ELECTRIC SKATEBOARD ON
THE WHEELS LEVER-NOT STANDING ON END.
Repair Information
Many repaires that may be required for your Electric Skateboard are covered in the
maintenance section of this guide.Should your Electric Skateboard require repaires that are
not covered under this section,contact Manufacturer or Dealer with the nature of the problem
of Electric Skateboard.
For more information on how to obtain technical support or an authorized service center
location contact Skateboard Manufactuer or Dealer.
Manufacturer warranties your Electric Skateboard for 30 days from the date of original
purchase against manufacturer’s defects in materials and workmanship.The warranty DOES
NOT COVER MALFUNCTIONS RESULTING FROM NEGLECT,MISUSE,ABUSE,and
MODIFICATIONS TO THE BOARD OR FAILURE TO FOLLOW ALL SAFETY AND
USE WARNINGS CONTAINED HEREIN.
Warranty is limited to the Electric Skateboard.Manufactuer asumes NO LIABILITY for any
other components.

7
Parts Diagram of the Raptor:
1.Bolt
2.Plate
3.Washer
4.Truck base
5.Washer
6.Battery
7.Pull rod
8.Loop
9.Spring
10.Battery case
11.Block
12.Receiver
13.Plastic case
14.Screw
15.Nut
16.Washer
17.Spaer
18.Tyre
19.Bearing
20.Bushing
21.Axle
22.Washer
23.Nut
24.Socket
25.Transom
26.Control case
27.Screw
28.On/off
29.Controller
30.Nut
31.Snap link
32.Bolt
33.Screw
34.Nut
35.Snap link
36.Washer
37.Nut
38.Bearing
39.Brush holder
40.Brush
41.Screw
42.Rotor
43.Bolt
44.Tyre
45.Screw
46.Plate
47.Spacer
48.Gear
49.Belt
50.Screw
51.Belt housing
52.Axle
53.Screw
54.Motor cover
55.Bearing
56.Covering
57.Cap
58.Battery
59.Emitter