Mottura X Mode 99.690 User manual

POWERED ELECTRONIC LOCK
FINGERPRINT SCANNER
99.690
GENERAL WARNINGS
Mottura Serrature di Sicurezza S.p.A. thanks you for choosing this product and reminds you to:
- Read these instructions very carefully before installing and using this product and before doing any maintenance.
- Keep these instructions for future use and attach the sales receipt to validate the warranty.
- In case of problems, contact your authorized dealer only.
DO NOT use a liquid, spray, or wet cloth to clean the escutcheon! If liquids enter the scanner, they will oxidize and perma-
nently damage its components. Use a dry cloth only.
DO NOT paint the escutcheon with any method or substance. Failure to follow these instructions will immediately void
the warranty.
Mottura Serrature di Sicurezza S.p.A. reserves the right to modify the characteristics of the products described in these
instructions at any time and without notice. The ngerprint scanner must be powered ONLY with a direct current (DC) line
adapter with voltage from 8 to 24 V and current not below 350 mA (for example, Mottura adapter 99.683). Be very careful
to respect polarity.
DO NOT power the scanner in alternating current (AC): doing so will permanently damage it.
These power instructions refer ONLY to the ngerprint scanner, NOT to the lock, which has its own installation manual.
Battery power is not advisable: the batteries would drain very quickly.
After powering the scanner for the rst time, or after a blackout, you have to wait at least 10 minutes for the sensor to heat,
otherwise the scans may be incorrect.

99299GB - XMODE - FINGERPRINT SCANNER - REV. 00
2
INSTALLER
1 - ESCUTCHEON .................................................................................................................. pag. 3
2 - ASSEMBLY AND ELECTRICAL CONNECTION ...................................................................... 3
USER
3 - CHANGING THE PIN CODE ON THE INFRARED REMOTE CONTROL ............................ 5
4 - MASTER FINGERPRINTS ............................................................................................................. 5
5 - RECORDING MASTER FINGERPRINTS ..................................................................................... 6
6 - RECORDING SERVICE FINGERPRINTS ..................................................................................... 6
7 - IDENTIFICATION AND OPENING OF THE LOCK ................................................................. 7
8 - DELETING ALL FINGERPRINTS, FACTORY RESET ............................................................... 7
9 - LOCKING THE SCANNER ............................................................................................................ 7
10 - UNLOCKING THE SCANNER ...................................................................................................... 7
CONTENTS

3
2. ASSEMBLY AND ELECTRICAL CONNECTION
Make a 50 x 38 mm opening in the door panel as shown in the gure.
1. ESCUTCHEON
INSTALLER
GREEN / RED LED
(FUNCTIONS SIGNAL)
BLUE LED
(POWER STATUS)
BRUSHED STEEL ESCUTCHEON
SWIPE-TYPE FINGERPRINT
SCANNER WITH SENSOR
SELF-CLEANING DEVICE
Connect the scanner to the door opener logic unit.
RESET KEY: press for 5 sec. to return the
scanner to factory settings.
AUTHENTICATION KEY: required only if the ope-
ner logic unit is replaced.
ESCUTCHEON
OPENER LOGIC UNIT
AUTHENTICATION KEYRESET KEY
THE OPENER LOGIC UNIT must be placed inside the door at a point that is INACCES-
SIBLE from the outside (BURGLAR-RESISTANT).

99299GB - XMODE - FINGERPRINT SCANNER - REV. 00
4
Connect the ngerprint scanner to the lock and to the line adapter.
Fix the scanner to the panel with the screws (supplied) and cover the base with the brushed stainless steel escutcheon
(supplied).
Cable
99701
99683
LINE
ADAPTER
-
+
The connections must be made by a qualied technician in conformity to current electrical safety standards
and to Rules of Good Engineering.
N.B. All connections must be made with the electrical supply switched o and the batteries disconnected.
Cable
99701
INSTALLER
YELLOW
WHITE
GREEN
BROWN

5
3. CHANGING THE PIN CODE ON THE INFRARED REMOTE CONTROL
For security reasons, you should change the factory-set PIN code with a personal
PIN code, BEFORE recording any master or service ngerprint.
1 - Remote control pointed to blue LED
2 - Press D
3 - Press E
4 - Enter factory-set PIN
5 - Press OK
6 - Enter personal PIN (4-6 digits)
7- Press OK
Your hands must be very clean when recording ngerprints. Use n-
gers without scars, otherwise they will be dicult to record or the
results will be low quality.
4. MASTER FINGERPRINTS
The master ngerprint is NOT used to open the lock, but only to access programming/deletion of the service ngerprints
on the scanner. We advise you NOT to use ngers habitually used.
As soon as you power-on the scanner, the two LEDs (green and red) light permanently. You must now record one or more
master ngerprints in order to access the functions. You can record up to 3 master ngerprints (see the next section) by
swiping your nger on the scanner as shown in the gure.
NO !OK !
Switch on power to the scanner and to the XMODE lock, and check that the blue LED located in the inside niche of the
scanner is on.
N.B. The remote control is supplied with a preset PIN code (shown on the adhesive label on the remote control).
1
7
6
3
5
4
2
INSTALLER
USER

99299GB - XMODE - FINGERPRINT SCANNER - REV. 00
6
1234567
1
MASTER
FINGER-
PRINT
Swipe
nger on
scanner
Red
and
green
LEDs go o
and then
back on *
Repeat
step 1 after
3 seconds
Red
and
green
LEDs go o
and then
back on *
Repeat
step 1 after
3 seconds
Only
green LED
stays on
briey
Red
and
green
LEDs go o;
recording
done
2
DIFFERENT
MASTER
FINGER-
PRINTS
Swipe
nger on
scanner
Red
and
green
LEDs go o
and then
back on *
Repeat
step 1 after
3 seconds
Red
and
green
LEDs go o
and then
back on *
After
3 seconds,
swipe another
master nger
Only
green LED
stays on
briey
Red
and
green
LEDs go o;
recording
done
3
DIFFERENT
MASTER
FINGER-
PRINTS
Swipe rst
nger on
scanner
Red
and
green
LEDs go o
and then
back on *
After
3 seconds,
swipe second
master nger
Red
and
green
LEDs go o
and then
back on *
After
3 seconds,
swipe third
master nger
Only
green LED
stays on
briey
Red
and
green
LEDs go o;
recording
done
6. RECORDING SERVICE FINGERPRINTS
The service ngerprint is used only to open the lock. It cannot be used for recording/deletion functions. The ngers used
to record service ngerprints must be DIFFERENT from the ones used as master ngerprint. Up to 150 dierent ngerprints
can be recorded.
1 - Swipe the master nger on the scanner
2 - The red and green LEDs light briey *
3 - Swipe the service nger
4 - The green LED lights briey*; recording done
5 - After a few seconds the red and green LEDs start ashing; exit from programming
* If the nger is not recognized, only the red LED lights briey and you have to repeat the procedure.
** If you want to record more service ngers, repeat steps 3 and 4.
Repeat the procedure for each service ngerprint you want to record, up to a maximum of 150.
5. RECORDING MASTER FINGERPRINTS
* If the scan is faulty, the two LEDs stay on steadily and you have to repeat the procedure.
USER

7
9. LOCKING THE SCANNER
10. UNLOCKING THE SCANNER
Swipe a nger with an unrecorded ngerprint ten times: the red LED will light briey after each swipe and you will have to
wait about one second. After ten swipes the scanner will be locked.
Swipe a nger with a recorded ngerprint (master or service). The green LED will light and the red LED will start ashing.
After a few seconds they will both go o and the scanner will be back in operation.
8. DELETING ALL FINGERPRINTS, FACTORY RESET
With the infrared remote control:
1 - Remote control pointed to blue LED
2 - Press DA
3 - Enter personal PIN; green LED light briey
4 - Press OK ; green LED and then green and red LED ash.
The green and red LEDs on steadily indicate that deletion is done.
The scanner has been factory reset and no longer contains any ngerprints.
With master ngerprint:
1 - Swipe the master nger 3 times on the scanner
2 - The red and green LEDs light briey *
3 - Green LED on: procedure done
4 - Green and red LEDs on: deletion done
* If the nger is not recognized, only the red LED lights briey and you have to repeat
the procedure
The scanner has been factory reset and no longer contains any ngerprints.
1
4
3
2
USER
7. IDENTIFICATION AND OPENING OF THE LOCK
When the service nger is swiped, the green LED lights and the lock opens. If not (nger not recognized, nger dirty, or
poor quality scan), the red LED will light briey.

99299GB - 07/14 - a_013434
www.mottura.it