Mountain Buggy Urban Double U2204 User manual

IMPORTANT - KEEP FOR FUTURE REFERENCE
DTCCGis8/05/08gen
Graco®
model: SnugRide®
- Double/triple carseat clip instructions
The stroller seat does not need to be removed to t Carseat Clip.
Unfasten fasteners (x) either side
of right-hand seat and peel fabric
back, exposing right-hand side
tube and centre bar.
1
Recline right-hand seat slightly.
2
3
ALL MODELS
Loosen the strap beneath seat
at point A .
URBAN
These instructions are for the Carseat Clip that ts the SnugRide®infant
car seat made by Graco®only. This Carseat Clip ts the following
model strollers:
DOUBLE U2204
WARNING
• CheckyouhavetheGraco®model: SnugRide®
CarSeatforthisCarseatClip.
• Do not use this Carseat Clip until you have
readandunderstoodtheinstructions!
• Incorrectusecanmeanseriousinjuryordeath
toaninfant!
• Do not use this Carseat Clip on any other
strollerasitmaybeunsafe.
• Neverleaveyourchildunattended.
• CheckthatcarseatandCarseatCliparesecure
andcannotmoveforward,back,sidewaysor
upwards.
• Make sure infant is harnessed into the
car seat using the car seat manufacturer’s
instructions.
• Donotleavebabyincarseat(onoroffstroller)
forlongperiodsoftime.
STAGE 1
Pull support wire out of
sunhood joint A while
pushing against stroller frame
with other hand B.NB:This
operation is child proof and
therefore requires a degree
of force.
Repeat step (1) on other
side.
Fold sunhood back to rest on
handlebar.
3
1.TemporarilyRemoveSunhood
2
The sunhood wires need to be removed from sunhood joints to allow
Carseat Clip to be tted. These wires are re-attached to stroller once
Carseat Clip has been tted.
A
B
Sunhood Joint
URBAN
TRIPLE U3204
URBAN
DOUBLE T2204
TERRAIN
TRIPLE T3204
TERRAIN
1
STAGE 2
ALL MODELS
1.PartialSeatUnfastening
Note: The Carseat Clip ts to right hand seat only. Left and right are
determined from pusher position.
A
centre
bar
X

WARNING
• Check Carseat Clip is located correctly on to
strollerframe.Referbacktodiagramstoensure
positioningofSnapLocksarecorrect.
• Check car seat and Carseat Clip are secure
and cannot move forward, back, sideways or
upwards.
• Do not use Carseat Clip if you are unable to
secure car seat or Carseat Clip.  In this case
contactstorewherestrollerwaspurchasedor
distributorforyourcountry,formorehelp.
RemovingCarSeat
from Carseat Clip
Pull up car seat latch handle
to release car seat from Carseat
Clip bar.
Lift car seat off Carseat Clip.
Remove sunhood wires (refer Stage 1).
Open both Snap Locks by lifting up levers.
Lift Carseat Clip off stroller frame
Re-attach sunhood wires (refer Stage 3).
Re-attach two middle fasteners on both sides of seat.
Tighten strap beneath seat (refer Stage 1).
Fitting Carseat Clip to Frame
RettingSunhood
STAGE 3
2
WARNING
• Makesureinfantisharnessedintothecarseat
usingthecarseatmanufacturer’sinstructions.
• WhenttingcarseatontoCarseatClip,ALWAYS
KEEPASTEADYINGHANDONCARSEATAND
INFANT.
• IT IS RECOMMENDED THAT YOU PRACTISE
THEFOLLOWINGINSTRUCTIONSWITHOUT
INFANTINCARSEAT.
NB:TheCarseatClipcomesassembledfortheUrbanmodel.
Assembled for Urban Assembled for Terrain
CLOSEDPOSITION
Place car seat in Carseat
Clip so that infant is facing
away from stroller handlebar.
Ensure the car seat latch has
clicked on to the Carseat
Clip bar.
1
RemovingCarseatClipfromStroller
TerrainModelOnly
Before placing Carseat Clip on stroller frame, the Snap Lock at point
B needs to be removed and placed at point C.
(i) Using Allen Key supplied, remove Snap Lock at point Bby rotating
screw in an anti-clockwise direction.
(ii) Using Allen Key supplied, place removed Snap Lock at point Cby
rotating screw in a clockwise direction until screw is tight and Snap
Lock is secure.
Snap Locks
TERRAINANDURBANMODELS
Open both Snap Locks by
lifting up levers.
1
Locate centre bar lug on stroller
and slide the Carseat Clip
Sliding Plate down the centre
bar of frame until Groove (X) in
Sliding Plate locks onto centre
bar lug.
Press Carseat Clip on to right-
hand side tube of frame so that
the top Snap Lock is directly
above Sunhood Joint.
3
Close both Snap Locks down
at, making sure you hear the
lock “click” indicating they are
fully locked.
4
Snap
Lock Lever
OPENPOSITION
“CLICK”
Pictured on Urban
STAGE 4
STAGE 5
Carseat
Clip bar
Car Seat
Latch
1
2
1
2
Sliding
Plate
X Groove X Groove
Sliding
Plate
Allen Key
A
BBA
C
Allen Key Snap Locks
car seat
latch handle
Carseat
Clip bar
2
TERRAIN
Place sunhood in position and push
one side of wire into plastic joint.
Repeat on other side by pulling wire
away from frame at the top. Fasten
sunhood fabric to stroller frame and
seat, near handle bar.
3
4
5
URBAN
6
URBAN
Sunhood
joint
Top
Snap lock
Snap lock
Sunhood
joint
Carseat Clip
Sliding Plate
Carseat Clip
Sliding Plate
TERRAIN
URBAN
centre
bar
lug
Fitting Car Seat onto Carseat Clip
Right-hand
side tube
Right-hand
side tube