Moxa Technologies MC-7130-MP User manual

MC-7130-MP Hardware User’s Manual
Edition 4.0, February 2017
www.moxa.com/product
© 2017 Moxa Inc. All rights reserved.

MC-7130-MP Hardware User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Mox
a China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview...........................................................................................................................................1-2
Package Checklist...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
Hardware Specifications ......................................................................................................................1-3
Hardware Block Diagram..............................................................................................................1-5
2. Hardware Introduction ..................................................................................................................... 2-1
Appearance........................................................................................................................................2-2
Front View..................................................................................................................................2-2
Rear View...................................................................................................................................2-2
Dimensions........................................................................................................................................2-3
LED Indicators....................................................................................................................................2-4
Real Time Clock..................................................................................................................................2-4
3. Hardware Connection Description..................................................................................................... 3-1
Installing the MC-7130-MP...................................................................................................................3-2
Wiring Requirements...........................................................................................................................3-2
Connecting the Power .........................................................................................................................3-3
Grounding the MC-7130-MP .................................................................................................................3-3
Connecting Data Transmission Cables ...................................................................................................3-3
Connecting to the Network ...........................................................................................................3-3
Connecting to a Serial Device .......................................................................................................3-4
Connecting a PS/2 Keyboard and Mouse................................................................................................3-5
Connecting to the USB Device ..............................................................................................................3-5
Connecting to Digital Input and Output Channels....................................................................................3-5
Connecting to a VGA Monitor................................................................................................................3-6
Connecting to a DVI-D Monitor.............................................................................................................3-6
Connecting to a Speaker/Headphone/Microphone ...................................................................................3-6
Installing the Removable SATA Storage Drive.........................................................................................3-7
Installing the Internal SATA Storage Drive.............................................................................................3-7
Installing PCI and PCIe Cards...............................................................................................................3-9
Upgrading the Memory Module...........................................................................................................3-10
4. BIOS Setup........................................................................................................................................ 4-1
Entering the BIOS Setup Utility ............................................................................................................4-2
Main Information................................................................................................................................4-3
Advanced Settings..............................................................................................................................4-3
Boot Configuration ......................................................................................................................4-4
Peripheral Configuration...............................................................................................................4-4
HDC Configuration.......................................................................................................................4-5
Video Configuration .....................................................................................................................4-7
Chipset Configuration ..................................................................................................................4-8
Hardware Monitor........................................................................................................................4-9
Security Settings ................................................................................................................................4-9
TPM Status.................................................................................................................................4-9
TPM Operation ............................................................................................................................4-9
Set Supervisor Password............................................................................................................4-10
Power Settings .................................................................................................................................4-10
Advanced CPU Control ...............................................................................................................4-10
Boot Settings ...................................................................................................................................4-12
Boot Type.................................................................................................................................4-12
Quick Boot ...............................................................................................................................4-12
PXE Boot to LAN........................................................................................................................4-12
Add Boot Options ......................................................................................................................4-12
USB Boot .................................................................................................................................4-12
EFI Device First.........................................................................................................................4-13
Boot Delay Time........................................................................................................................4-13
Legacy.....................................................................................................................................4-13
Exit Settings ....................................................................................................................................4-14
Exit Saving Changes..................................................................................................................4-14
Save Change Without Exit ..........................................................................................................4-14
Exit Discarding Changes.............................................................................................................4-14
Load Optimal Defaults................................................................................................................4-14
Load Custom Defaults................................................................................................................4-14
Save Custom Defaults................................................................................................................4-15
Discard Changes .......................................................................................................................4-15
Upgrading the BIOS..........................................................................................................................4-15
A. Regulatory Approval Statement ........................................................................................................ A-1

B. Adjusting the Audio Mixer Function .................................................................................................. B-1

1
1. Introduction
The MOXA MC-7130-MP marine computer is powered by the third generation Intel® Core™ i3 3120ME
processor and offers a wide range of I/O connectivity that includes eight NMEA 0183 ports, four serial ports,
four Gigabit Ethernet ports, six USB 2.0 and two SuperSpeed USB 3.0 ports. In addition, it also provides a third
generation PCIe x16 slot alongside two standard PCI slots, allowing versatile peripheral expansion for industrial
applications.
The MC-7130-MP’s rugged and fanless design and 1G anti-vibration make it particularly well-suited for bridge
systems in marine applications. In addition, the compact size and low power consumption ensure an easy
installation and dependable service, while its modular design allows easy integration with existing displays.
Users can easily install Windows 7, Windows XP SP3, or Windows XP Embedded to provide a flexible and
friendly environment for system development and application implementation.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Hardware Specifications
Hardware Block Diagram

MC-7130-MP Hardware Introduction
1-2
Overview
The MOXA MC-7130-MP marine computer is powered by the third generation Intel® Core™ i3 3120ME
processor and offers a wide range of I/O connectivity including eight NMEA 0183 ports, four serial ports, four
Gigabit Ethernet ports, six USB 2.0 and two SuperSpeed USB 3.0 ports. In addition, it also provides a third
generation PCIe x16 slot alongside two standard PCI slots, allowing versatile peripheral expansion for industrial
applications.
Users can also choose to install Windows 7, Windows XP SP3, or Windows XP Embedded operating systems to
provide a flexible and friendly environment for system development and application implementation.
Package Checklist
One MC-7130-MP:
A ready-to-run x86 computing platform with Intel Core™ i3 3120E, 4 serial ports, 4 Gigabit Ethernet ports, 6
USB hosts, 8 NMEA ports, storage drives, and VGA/DVI-D video outputs.
Each model ships with the following items:
•1 MC-7130-MP marine computer
•2 storage protection locks (with keys)
•8 screws for drive mounts
•Wall mounting kit, with 6 screws
•1 terminal block for DC power input
•2 6-pin digital input terminal blocks
•2 8-pin digital output terminal blocks
•8 NMEA 0183 ports
•Documentation and driver CD
•Quick Installation Guide (printed)
•Warranty card
NOTE
Please notify your sales representative if any of the above items are missing or damaged.
Product Features
The MC-7130-MP embedded computer has the following features:
•High-performance 3rd generation Intel Core i3 3120ME processor
•Built-in 4 GB DDR3 memory, with additional capacity up to 16 GB
•Supports three independent displays (2 DVI-D + 1 VGA)
•4 Gigabit Ethernet ports for network redundancy
•1 PCIe (x16) slot, 2 universal PCI slots
•2 software-selectable RS-232/422/485 serial ports
•2 RS-232 ports
•8 NMEA 0183 ports
•6 USB 2.0 hosts, 2 USB 3.0 ports
•2 integrated SATA 6 Gbps and 2 SATA 3 Gbps interfaces for high speed storage expansion
•Trusted Platform Module: integrated hardware-level security for maximum data protection
•1G anti-vibration design for system reliability
•24 VDC and 100 to 240 VAC power input
•Supports Windows XP Embedded, Windows XP SP3, or Windows 7

MC-7130-MP Hardware Introduction
1-3
Hardware Specifications
Computer
CPU:
Intel® Core™ i3-3120ME (BGA CPU package), dual core threaded 64 bit 2.4 GHz processor
OS:
Windows 7, Windows XP SP3, Windows XP Embedded (must be installed by the user)
System Chipset:
Intel® QM77 Express Chipset
System Memory:
16 GB capacity, 4 GB pre-installed: 2 slots of 8 GB DDR3-1066 204 pin SO-
DIMM SDRAM
USB:
USB 2.0 host x 6, USB 3.0 host x 2, Type A connectors
Storage
Storage Support:
• 2 SATA 6 Gb/s ports for SSD/HDD
• 2 SATA 3 Gb/s ports for SSD/HDD
Other Peripherals
KB/MS:
2 PS/2 interfaces supporting standard PS/2 keyboard and mouse
Audio:
Line in x 1, Line out x 1, Mic in x 1
LPT Port:
1
PCIe x16 Slots:
1
PCI Slots:
2
Display
Graphics Controller:
Onboard Intel® HD 4000 graphics
Display Interface:
• VGA Interface
x 1: 15-pin D-Sub connector (female), with resolution up to 1920 x 1080
• DVI
-D Interface x 2: 29-pin DVI-D connectors (female), with resolution up to 1920 x 1080, 60Hz (with
reduced blanking)
Ethernet Interface
LAN:
4 auto-sensing 10/100/1000 Mbps ports (RJ45)
Magnetic Isolation Protection:
1.5 KV built in
Serial Interface
Serial Standards:
• 2 RS
-232/422/485 ports, software-selectable (DB9 male)
• 2 RS
-232 ports (DB9)
• 8 NMEA 0183 terminals (NMEA 2000
available on request)
Serial Communication Parameters
Data Bits:
5, 6, 7, 8
Stop Bits:
1, 1.5, 2
Parity:
None, Even, Odd, Space, Mark
Flow Control:
RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485
Baudrate:
50 bps to 230.4 Kbps
Serial Signals
RS
-232: TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND
RS
-422: TxD+, TxD-, RxD+, RxD-, GND
RS
-485-4w: TxD+, TxD-, RxD+, RxD-, GND
RS
-485-2w: Data+, Data-, GND
NMEA Interface
Serial Standards:
NMEA 0183v2 (NMEA 2000
available on request)
Base Serial Standard:
• NMEA 0183: RS
-422
• NMEA 2000: CAN bus (Available on request)
Optical Isolation Protection:
3 KV
Voltage Differential:
-15 V to +15 V
Baudrate:
4800 bps
Data Bits:
8

MC-7130-MP Hardware Introduction
1-4
Stop Bits:
1, 1.5, 2
Parity:
None
Handshake:
None
Digital Input
Input Channels:
8 dry channels, with 4 grounds
Digital Input Levels for Dry Contacts:
• Logic level 0: Close to GND
• Logic level 1: Open
Connector Type:
6-pin Phoenix-compatible 3.81 mm screw terminal block, x 2
Isolation:
ESD protection to DNV specifications
Relay Output
Type:
Form A (N.O.) power relay
Output Channels:
8 output channels
Contact Rating:
2A, 30Vdc /0.5A, 125Vac under resistor load
Initial Insulation Resistance:
1000M ohm (min.) @500VDC
Mechanical Endurance:
100,000 operations @2A, 30VDC resistive load
Electrical Endurance:
100,000,000 operations
Contact Resistance:
Max. 50m ohm @6V, 0.1A
Connector Type:
8-pin Phoenix-compatible 3.81 mm screw terminal block, x 2
Isolation:
Relay isolation; ESD protection to DNV specifications
LEDs
System:
Storage, Power
LAN:
100M/Link x 4, 1000M/Link x 4 (on connector)
Physical Characteristics
Housing:
Aluminum, sheet metal
Weight:
8 kg
Dimensions:
322 x 300 x 150 mm (12.68 x 11.81 x 5.91 in)
System Cooling:
Moxa AI-Fan
Mounting:
Wall
Environmental Limits
Operating Temperature:
-15 to 55°C (5 to 131°F)
Storage Temperature:
-20 to 60°C (-4 to 131°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Anti
-Vibration:
• 0.7 g @ DNV 2.4 (Class A), sine wave, 2
-100 Hz, 1 Oct./min., 1.5 hr per axis
• 1 grms @ DNV 2.4, random wave, 3
-100 Hz, 2.5 hr per axis
• 2.1 g @ DNV 2.4 (Class C), sine wave, 2
-50 Hz, 1 Oct./min., 1.5 hr per axis
Power Requirements
Input Voltage:
• DC: 24 VDC (with tolerance from 18 to 30 VDC, 2
-pin terminal block)
• AC: 100 to 240 VAC
Power Consumption:
Less than 100 W, 2.5 A @ 24 VDC
Standards and Certifications
Safety:
UL 60950-1, DNV 2.4 (Pending), IEC 60945 (4th) (Pending), IACS-E10 (Pending), CCC (GB4943,
GB9254, GB17625.1) (Pending)
EMC:
EN 55032 Class B, EN 55024-4-2, EN 55024-4-3, EN 55024-4-4, FCC Part 15 Subpart B Class B
Marine:
IEC 60945 4th. (Pending), IACS-E10 (Pending)
Green Product:
RoHS, cRoHS, WEEE
Reliability
MTBF (mean time between failures):
• Telcordia (Bellcore) Standard TR/SR: 269,934 hrs
• MIL
-HDBK-217 FN2: 114,305 hrs

MC-7130-MP Hardware Introduction
1-5
Warranty
Warranty Period:
3 years
Details:
See www.moxa.com/warranty
Hardware Block Diagram

2
2. Hardware Introduction
The MC-7130-MP computer is compact, well-designed, and built rugged enough for industrial applications. LED
indicators help you monitor performance and identify trouble spots, multiple serial ports allow you to connect
different devices, and the reliable and stable hardware platform lets you devote your attention to developing
your applications.
The following topics are covered in this chapter:

Appearance
Front View
Rear View

Dimensions

LED Indicators

Real Time Clock

MC-7130-MP Hardware Hardware Introduction
2-2
Appearance
Front View
Rear View

MC-7130-MP Hardware Hardware Introduction
2-3
Dimensions

MC-7130-MP Hardware Hardware Introduction
2-4
LED Indicators
LED Name LED Color LED Function
Power (on front panel) Green Power is on and functioning normally
Off Power is off or power error exists
Storage (on front panel) Red (on) Storage disk is functioning properly
Red (blinking) Storage disk is accessing data
Off No activity
LAN (1 to 4)
(on connectors)
Green 100 Mbps Ethernet mode
Yellow 1000 Mbps (Gigabit) Ethernet mode
Off No activity or 10 Mbps Ethernet mode
Real Time Clock
The embedded computer’s real-time clock is powered by a lithium battery. We strongly recommend that you
NOT replace the lithium battery on your own. If the battery needs to be changed, contact the Moxa RMA service
team at http://www.moxa.com/rma/about_rma.aspx.
ATTENTION
Used
batteries are environmentally hazardous materials. Dispose of them in the proper manner.
WARNING
There is a risk of explosion if the wrong type of battery is used. To avoid this potential danger, always be sure
to use the correct type of battery. Contact the Moxa RMA service team if you
have any questions about
replac
ing your battery.

3
3. Hardware Connection Description
In this chapter, we show how to connect the embedded computers to the network and to various devices.
The following topics are covered in this chapter:

Installing the MC-7130-MP

Wiring Requirements

Connecting the Power

Grounding the MC-7130-MP

Connecting Data Transmission Cables
Connecting to the Network
Connecting to a Serial Device

Connecting a PS/2 Keyboard and Mouse

Connecting to the USB Device

Connecting to Digital Input and Output Channels

Connecting to a VGA Monitor

Connecting to a DVI-D Monitor

Connecting to a Speaker/Headphone/Microphone

Installing the Removable SATA Storage Drive

Installing the Internal SATA Storage Drive

Installing PCI and PCIe Cards

Upgrading the Memory Module

MC-7130-MP Hardware Hardware Connection Description
3-2
Installing the MC-7130-MP
Wall or Cabinet Mounting
The MC-7130-MP provides two brackets for mounting, either onto walls or into cabinets. Attach the brackets
with the screws included on both sides of the chassis.
Wiring Requirements
You should read and follow these common safety precautions before proceeding with the installation of any
electronic device:
•Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross, make sure the wires are perpendicular at the intersection point.
NOTE
Do not run signal or communication wiring together with power wiring in the same wire conduit. To avoid
interference, wires with different signal characteri
stics should be routed separately.
•Use the type of signal transmitted through a wire to determine which wires should be kept separate. The
rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separate.
•It is advisable to label the wiring on all devices in the system.
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your
MC-7130-MP.
Wiring
Caution!
Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could overheat, causing s
erious damage to your
equipment.
Temperature Caution!
Be careful when handling
the unit. When the unit is plugged in, the internal components generate heat, and
consequently the outer casing may feel hot to the touch.

MC-7130-MP Hardware Hardware Connection Description
3-3
Connecting the Power
The MC-7130-MP comes with a 100 to 240 VAC power input, and also has a 24 VDC power input (via the
terminal block). If power is supplied properly, the Power LED will light up.
For safety reasons, please use cables with the following specifications:
Wire range: 14-22 AWG
Torque: 7 lb
Grounding the MC-7130-MP
Grounding and careful wire routing help limit the effects of noise due to electromagnetic interference (EMI).
Run the ground connection from the ground screw to the grounding surface prior to connecting the power.
ATTENTION
This product is intended to be mounted
on a well-grounded surface, such as a metal panel.
Earthing/Grounding Wire: See the figure shown below for the location of the earth ground on the terminal block
power connector. Connect the EG wire to an appropriately grounded metal surface.
Connecting Data Transmission Cables
This section describes how to connect the MC-7130-MP computer to the network and/or serial devices.
Connecting to the Network
Plug your network cable into the computer’s Ethernet port. The other end of the cable should be plugged into
your Ethernet networking device. When the cable is properly connected, the LEDs on the embedded computer’s
Ethernet port will glow to indicate a valid connection.
The 10/100/1000 Mbps Ethernet LAN ports use 8-pin RJ45 connectors. The following diagram shows the
pinouts for these ports.

MC-7130-MP Hardware Hardware Connection Description
3-4
The LED indicator
s on the right-top (for the upper LAN connector) and right-bottom
(for the
lower LAN connector)
co
rners glow a solid green color when the cable is properly connected
to a 100 Mbps Ethernet network. The LED will flash on and off when Ethernet packets are
being transmitted or received.
The LED indicator
s on the left-top and left-bottom corners glow a solid yellow
color when the
cable is properly connected to a 10
00
Mbps Ethernet network. The LED will flash on and off
when Ethernet packets are being transmitted or received.
Pin 10/100 Mbps 1000 Mbps
1 ETx+ TRD(0)+
2 ETx- TRD(0)-
3 ERx+ TRD(1)+
4 – TRD(2)+
5 – TRD(2)-
6 ERx- TRD(1)-
7 – TRD(3)+
8 – TRD(3)-
Connecting to a Serial Device
The serial ports use DB9 connectors. COM1 and COM2 can run with RS-232, and COM3 and COM4 run with
RS-232, RS-422, or RS-485. The pin assignments are shown in the following table:
DB9 Male
Port
RS
-232/422/485 Pinouts
Pin RS-232 RS-422 RS-485
(4-wire)
RS-485
(2-wire)
1 DCD TxDA(-) TxDA(-) –
2 RxD TxDB(+) TxDB(+) –
3 TxD RxDB(+) RxDB(+) DataB(+)
4 DTR RxDA(-) RxDA(-) DataA(-)
5 GND GND GND GND
6 DSR – – –
7 RTS – – –
8 CTS – – –
Additionally, eight NMEA serial ports with terminal blocks are also available on the rear panel of the computer.
Refer to the following figures for the location of the NMEA ports and the pin assignments.

MC-7130-MP Hardware Hardware Connection Description
3-5
Connecting a PS/2 Keyboard and Mouse
Your MC-7130-MP computer comes with 2 PS/2 mini-DIN connectors on the rear panel to connect to a PS/2
keyboard and PS/2 mouse. This 6-pin mini-DIN connector has the pin assignments shown below.
PS/2 Connector
Pin No. Signal Definition
1 PS/2 Keyboard Data
2 PS/2 Mouse Data
3 GND
4 VCC
5 PS/2 Keyboard Clock
6 PS/2 Mouse Clock
Connecting to the USB Device
The MC-7130-MP comes with two USB 2.0 hosts on the front panel, four USB 2.0 hosts, and two SuperSpeed
USB 3.0 hosts on the rear panel. The USB ports support peripherals such as a keyboard or mouse, or storage
devices such as a portable HDD or DVD-ROM. Please note that USB 3.0 interfaces are not supported by the
Windows XP platform.
Connecting to Digital Input and Output
Channels
The MC-7130-MP comes with eight digital input and eight digital output channels on the rear panel. These
input/output channels can be connected with the terminal blocks which have been included in the package. See
the following figure for the pin assignments.

MC-7130-MP Hardware Hardware Connection Description
3-6
Connecting to a VGA Monitor
The MC-7130-MP comes with a D-Sub 15-pin female connector on the rear panel to connect a VGA CRT monitor.
To ensure that the monitor image remains clear, be sure to fasten the monitor cable using the cable’s
thumbscrews after connecting it to the MC-7130-MP. The pin assignments of the VGA connector are shown
below.
DB15 Female Connector
Pin No. Signal Definition Pin No. Signal Definition
1 Red 9 VCC
2 Green 10 GND
3 Blue 11 NC
4 NC 12 DDC Data
5 GND 13 HSYNC
6 GND 14 VSYNC
7 GND 15 DDC Clock
8 GND
Connecting to a DVI-D Monitor
The MC-7130-MP computers come with two DVI-D connectors that can connect to DVI monitors. Use the cable
to connect one end to the DVI-I connector and the other end to the monitor. See the following table for DVI-D
connector pin assignments. Please note that three independent displays are not supported under the Windows
XP operating system.
DVI-D Connector
Pin No. Signal Definition
1 T.M.D.S. Data2-
2 T.M.D.S. Data2+
3 T.M.D.S. Data2/4 Shield
4 N/C
5 N/C
6 DDC Clock
7 DDC Data
8 Analog Vertical Sync
9 T.M.D.S. Data1-
10 T.M.D.S. Data1+
11 T.M.D.S. Data1/3 Shield
12 N/C
Pin No. Signal Definition
13 N/C
14 +5V Power
15 Ground
(return for +5V, HSync, and VSync)
16 Hot Plug Detect
17 T.M.D.S. Data0-
18 T.M.D.S. Data0+
19 T.M.D.S. Data0/5 Shield
20 N/C
21 N/C
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock-
Connecting to a
Speaker/Headphone/Microphone
The MC-7130-MP comes with audio input, output, and microphone interfaces on the rear panel for connecting
a microphone, speaker, or headphones.

MC-7130-MP Hardware Hardware Connection Description
3-7
Installing the Removable SATA Storage Drive
The MC-7130-MP computer comes with a removable SATA storage device tray that is accessible through the
front panel. Either a SATA hard disk or solid state drive may be installed, but only use of an SSD will ensure full
anti-vibration compliance. To install a SATA storage device, please follow these instructions:
1. Disconnect the MC-7130-MP from the power source.
2. To remove the storage device tray, insert the protection key and turn it to the right, then unfasten the two
thumbscrews that secure the removable tray. The storage tray’s location may be seen in the following
figure:
3. Take off the storage bracket from the slot and turn it over to get access to the four screws which will secure
the drive to the tray.
4. Place the drive into the tray and secure it using the four screws. When finished, insert the tray into the
computer and fasten the tray in place using the two thumbscrews on the front panel. Finally, complete the
installation by turning the key leftwards to lock the tray into place.
Installing the Internal SATA Storage Drive
The MC-7130-MP has a SATA connector within the main chassis where a SATA storage drive may be
permanently installed. To install a 2.5-inch SATA storage drive, follow these instructions.
Turn over the MC-7130-MP to get access to its bottom panel; remove the four screws on the drive bay cover
plate. The following figure shows what the location of the screws:
After removing the cover plate, you will need to install the storage drive.