Moxa Technologies MGate 5105-MB-EIP User manual

– 1 – – 2 – – 3 –
P/N: 1802051050011
MGate 5105-MB-EIP
Quick Installation Guide
Second Edition, June 2014
Overview
The MGate 5105-MB-EIP is an industrial Ethernet gateway for
Modbus RTU/ASCII/TCP and EtherNet/IP network communication.
Package Checklist
Before installing the MGate 5105-MB-EIP, verify that the package
contains the following items:
•1 MGate 5105-MB-EIP gateway
•RJ45 to DB9 cable (for console use)
•Documentation and software CD
•Quick installation guide
•Warranty card
Optional Accessories:
•DR-45-24: 45W/2A DIN rail 24 VDC power supply with
universal 85 to 264 VAC input
•DR-75-24: 75W/3.2A DIN rail 24 VDC power supply with
universal 85 to 264 VAC input
•DR-120-24: 120W/5A DIN rail 24 VDC power supply with 88 to
132 VAC/176 to 264 VAC input by switch
•WK-36-02: Wall mounting kit
•Mini DB9F-to-TB Adaptor: DB9 female to terminal block
adapter
Please notify your sales representative if any of the above items
are missing or damaged.
Hardware Introduction
LED Indicators
LED
Color
Description
Ready
Off
Power is off or fault condition exists
Green
Steady: Power is on and the MGate is
functioning normally
Blinking: The MGate has been located by
the MGate Manager’s Location function
Red
Steady: Power is on and the MGate is
booting up
Blinking slowly: Indicates an IP conflict, or
DHCP or BOOTP server is not responding
properly
Flashing quickly: microSD card failed
EIP
(Scanner)
Off
No I/O data is exchanged
Green
Steady: I/O data is exchanged with all
devices
Blinking: I/O data is exchanged with at
least one device
(Not all configured devices can
communicate with gateway)
EIP
(Adapter)
Off
No I/O data is exchanged
Green
I/O data is exchanged with all devices
MB
Off
No communication with Modbus device
Green
Modbus communication progress
Red
Communication error
When MGate 5105 acts as Master:
1. Slave device returned an error
(exception)
2. Received frame error
(parity error,
checksum error)
3. Timeout (slave device no
response)
When MGate 5105 acts as Slave:
1. Received invalid function code
2. Master accessed invalid register
address or coil addresses
3. Received frame error
(parity error,
checksum error)
Dimensions
Unit: mm (inch)
Reset Button
Restore the MGate to factory default settings by using a pointed
object (such as a straightened paper clip) to hold the reset button
down until the Ready LED stops blinking (approx. 5 seconds).
Pull-high, Pull-low, and Terminator for RS-485
Remove the MGate 5105-MB-EIP’s top cover and you will find DIP
switches to adjust each serial port’s pull-high resistor, pull-low
resistor, and terminator.
SW
1
2
3
Pull-high
resistor
Pull-low
resistor
Terminator
ON
1 kΩ
1 kΩ
120 Ω
OFF
150 kΩ*
150 kΩ*
–*
*Default

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2014 Moxa Inc. All rights reserved.
Hardware Installation Procedure
1. Connect the power adapter. Connect the 12-48 VDC power line
or DIN rail power supply to the MGate 5105-MB-EIP device’s
terminal block.
2. Use a Modbus serial cable to connect the MGate to a Modbus
slave device.
3. Use an Ethernet cable to connect the MGate to the EtherNet/IP
controller.
4. The MGate 5105-MB-EIP is designed to be attached to a
DIN rail or mounted on a wall. For DIN rail mounting, push
down the spring and properly attach it to the DIN rail until it
“snaps” into place. For wall mounting, install the wall mount kit
(optional) first, and then screw the device onto the wall. The
following figure illustrates the two mounting options:
Software Installation Information
To install MGate Manager, insert the MGate Documentation and
Software CD into your PC’s CD-ROM drive, and then run the
following setup program to begin the installation process from the
“Software” directory:
MGM_Setup_[Version]_Build_[DateTime].exe
The filename of the latest version may have the following format:
MGM_Setup_Verx.x.x_Build_xxxxxxxx.exe.
For detailed information about MGate Manager, refer to the MGate
5105-MB-EIP User's Manual, which can be found in the “Document”
directory.
Pin Assignments
Modbus Serial Port (Male DB9)
Pin
RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O.
Common
N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
455 mA @ 12 VDC, 125 mA @ 48 VDC
Operating Temperature Standard models: 0 to 60°C (32 to
140°F)
Wide temp. models: -40 to 75°C (-
40
to 167°F) for –T model
Ambient Relative Humidity
5 to 95% RH
Dimensions
36 x 105 x 140 mm
(1.42 x 4.13 x 5.51 in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
513,139 hrs
1. DEMKO Certification number: 13 ATEX 1307610X
IEC Certification Number: IECEx UL 13.0051X;
2. Ambient Temperature Range (-40°C ≤ Tamb ≤ 75°C)
3. Certification String: Ex nA nC IIC T3 Gc
4. Standards Covered: EN 60079-0:2012/IEC 60079-0 6th Ed.
AND EN 60079-15:2010/IEC 60079-15 4th Ed.
5. The conditions of safe usage:
a. The Ethernet Communications Devices are intended for
mounting in a tool-accessible IP54 enclosure and used in
an area of not more than pollution degree 2 as defined by
IEC 60664-1.
b. Conductors suitable for use in an ambient temperature
greater than 86°C must be used for the power supply
terminal.
c. A 4mm2conductor must be used when connection to the
external grounding screw is utilized.
d. Provisions shall be made, either in the equipment or
external to the equipment, to prevent the peak rated
voltage being exceeded by the transient disturbances of
more than 140%.
Terminal Block (Plug mated with Socket): Rated 300 V, 10 A,
105°C, 12-28 AWG (0.0804 mm2- 3.31 mm2) wire size, torque
value 4.5 lb-in (0.509 N-m). The input terminal cable size 14 AWG
(2.1 mm2).
Moxa Inc.
Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Dist., New Taipei City, 23145
Taiwan, R.O.C.