Moxa Technologies OnCell G3470A-LTE Installation and operation manual

OnCell G3470A-LTE User’s Manual
Edition 1.1, July 2016
www.moxa.com/product
© 2016 Moxa Inc. All rights reserved.

OnCell G3470A-LTE User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2016 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Ame
ricas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview ...........................................................................................................................................1-2
Package Checklist ...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
Product Specifications .........................................................................................................................1-3
Functional Design ...............................................................................................................................1-5
LED Indicators ............................................................................................................................1-6
Beeper .......................................................................................................................................1-7
Reset Button...............................................................................................................................1-7
2. Getting Started ................................................................................................................................. 2-1
First-time Installation and Configuration ................................................................................................2-2
Step 1: Inserting a SIM Card ........................................................................................................2-2
Step 2: Turning on the OnCell G3470A-LTE ....................................................................................2-2
Step 3: Connecting the OnCell G3470A-LTE to a Computer...............................................................2-2
Step 4: Configuring the Computer’s IP Address ...............................................................................2-2
Step 5: Accessing the Web Console ...............................................................................................2-3
Step 6: Establishing a Cellular Connection ......................................................................................2-3
Step 7: Verifying the Cellular Connection .......................................................................................2-4
3. Web Console Configuration ............................................................................................................... 3-1
Accessing the Web Console ..................................................................................................................3-2
Configuration Menu Overview .......................................................................................................3-3
Overview ...........................................................................................................................................3-4
Basic Settings ....................................................................................................................................3-4
System Info Settings ...................................................................................................................3-4
Network Settings.........................................................................................................................3-5
Time Settings .............................................................................................................................3-5
Cellular Settings .................................................................................................................................3-6
Cellular WAN Settings ..................................................................................................................3-6
GuaranLink.................................................................................................................................3-8
Auto IP Report Settings.............................................................................................................. 3-11
GPS Settings ............................................................................................................................ 3-12
Oncell Central Manager Setting ................................................................................................... 3-12
Advanced Settings ............................................................................................................................ 3-12
DHCP Server (for AP mode only) ................................................................................................. 3-13
DDNS ...................................................................................................................................... 3-14
Packet Filters ............................................................................................................................ 3-14
SNMP Agent ............................................................................................................................. 3-16
Port Forwarding ........................................................................................................................ 3-18
VPN ......................................................................................................................................... 3-19
Auto Warning Settings....................................................................................................................... 3-26
System Log .............................................................................................................................. 3-26
Syslog ..................................................................................................................................... 3-27
E-Mail ...................................................................................................................................... 3-28
Relay ....................................................................................................................................... 3-30
Trap ........................................................................................................................................ 3-30
SMS ........................................................................................................................................ 3-32
Status ............................................................................................................................................. 3-33
DNS Information ....................................................................................................................... 3-33
SIM Status ............................................................................................................................... 3-33
Network Statistics ..................................................................................................................... 3-33
Routing Table ........................................................................................................................... 3-33
DHCP Client List (for AP mode only) ............................................................................................ 3-34
System Log .............................................................................................................................. 3-34
Relay Status ............................................................................................................................. 3-35
DI and Power Status.................................................................................................................. 3-35
VPN Log ................................................................................................................................... 3-36
Maintenance .................................................................................................................................... 3-37
Console Settings ....................................................................................................................... 3-37
Ping......................................................................................................................................... 3-37
Firmware Upgrade ..................................................................................................................... 3-38
Config Import Export ................................................................................................................. 3-38
Load Factory Default.................................................................................................................. 3-39
Password ................................................................................................................................. 3-39
Misc. Settings ........................................................................................................................... 3-39
Manual SMS.............................................................................................................................. 3-40
Remote SMS Control.................................................................................................................. 3-40
Save Configuration ........................................................................................................................... 3-41
Restart ............................................................................................................................................ 3-42

Logout ............................................................................................................................................ 3-42
4. Software Installation and Configuration ........................................................................................... 4-1
Overview ...........................................................................................................................................4-2
Wireless Search Utility.........................................................................................................................4-2
Installing the Wireless Search Utility ..............................................................................................4-2
Configuring the Wireless Search Utility...........................................................................................4-5
A. Supporting Information .................................................................................................................... A-1
Firmware Recovery .............................................................................................................................A-2
DoC (Declaration of Conformity)...........................................................................................................A-3
Federal Communication Commission Interference Statement ............................................................A-3
R&TTE Compliance Statement.......................................................................................................A-4
B. Dynamic Domain Name Server .......................................................................................................... B-1
C. Well-Known Port Numbers ................................................................................................................ C-1

1
1. Introduction
The OnCell G3470A-LTE industrial cellular gateway is an ideal wireless solution for remote monitoring
applications. With wide temperature support and power and antenna isolation design, the OnCell G3470A-LTE
is rugged enough for any harsh industrial environment.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Product Specifications

Functional Design
LED Indicators
Beeper
Reset Button

OnCell 3470A-LTE Introduction
1-2
Overview
The OnCell G3470A-LTE industrial cellular gateway provides a higher cellular bandwidth and more reliable
connection to your Ethernet network for cellular applications. With the integrated 4-port gigabit Ethernet
switch and LTE support, the OnCell G3470A-LTE offers a faster cellular connection with a lower total cost of
ownership. To enhance reliability, a key for industrial users, the OnCell G3470A-LTE features isolation design
for both power and antenna inputs. Coupled with high-level EMS and wide-temperature support, the OnCell
G3470A-LTE provides the highest level of device stability in any rugged environment. In addition, with dual SIM
and dual power-input features, the OnCell G3470A-LTE supports network redundancy to ensure that your
application’s network connectivity is not interrupted.
Package Checklist
Moxa’s OnCell G3470A-LTE is shipped with the following items. If any of these items is missing or damaged,
please contact your customer service representative for assistance.
•OnCell G3470A-LTE
•1 GPS connector terminator
•2 2G/3G/4G omni-directional antennas, 2 dBi, SMA (male)
•5 plastic RJ45 protective caps for serial console and Ethernet ports
•Quick installation guide (printed)
•Warranty card
NOTE
The above items
come with the standard OnCell G3470A-LTE model, but the package contents may var
y for
customized versions.
Product Features
•VPN support
•Multiple LTE band support:
EU Model: B1/B3/B7/B8/B20
US Model: B2/B4/B5/B13/B17/B25
•Universal cellular bands support for GSM/GPRS/HSPA
•Built-in 4-port Gigabit Ethernet switch for local network connectivity
•Virtual private responder/initiator support
•Industrial-grade design:
Dual power input for power redundancy
Dual-SIM support for cellular connection redundancy
Antenna isolation for 500V protection against radio interference
Power isolation for 500V power source insulation protection
-35°C to 70°C wide operating temperature (wide temperature support only applies to certain SKUs)

OnCell 3470A-LTE Introduction
1-3
Product Specifications
Cellular Interface
Standards:
GSM/GPRS/EDGE/UMTS/HSPA/LTE
Band Options:
OnCell
G3470A-LTE-EU:
• LTE 2100/1800/2600/900/800 MHz (B1/B3/B7/B8/B20)
• UMTS/HSPA 2100/1900/850/800/900 MHz
OnCell G3470A
-LTE-US:
• LTE 1900/AWS/850/700/1900 MHz (B2/B4/B5/B13/B17/B25)
• UMTS/HSPA 2100/1900/AWS/850/900 MHz
• Universal Quad
-band GSM/GPRS/EDGE 850/900/1800/1900 MHz
LTE Data Rate:
• Downlink: 100 Mbps (20 MHz bandwidth), 50 Mbps (10 MHz bandwidth)
• Uplink: 50 Mbps (20 MHz bandwidth), 25 Mbps (10 MHz bandwidth)
HSPA Data Rate:
• Downlink: Up to 42 Mbps (category 24)
• Uplink: Up to 5.76 Mbps (
category 6)
GPRS/EDGE Data Rate:
236 kbps Downlink/Uplink (Class 10/12)
LAN Interface
Number of Ports:
4
Ethernet:
10/100/1000 Mbps, RJ45 connector, Auto MDI/MDIX
Interface
Alarm Contact:
1 relay output with current carrying capacity of 1 A @ 24 VDC
Console Port:
RS-232 (RJ45)
Cellular Antenna Connectors:
2 SMA (female)
Digital Inputs:
2 electrically isolated inputs
+13 to +30 V for state “1”
+3 to
-30 V for state “0”
GNSS:
1 SMA (female), GPS (1575.42 MHz), GLONASS (1602 MHz)
LED Indicators:
PWR1, PWR2, READY, FAULT, CELLULAR SIGNAL, SIM1, SIM2, 2G, 3G, 4G, GPS
Ground Screw:
M5
Reset Button:
Power Reset/Factory Default Reset
Software
Network Protocols:
ICMP, TCP/IP, UDP, DHCP, Telnet, DNS, SNMP, HTTP, HTTPS, SMTP, SNTP, ARP
Routing/Firewall:
NAT, Port Forwarding, IP/MAC/Port Filtering
VPN:
• Max. Tunnel Number: 5 (Responder/Initiator)
• IPSec (DES, 3DES, AES, MD5, SHA
-1, DH2, DH5), PSK/X.509/RSA
Cell
ular Connectivity: GuaranLink
GPS:
NMEA
Others:
DDNS
Management Software
Utilities:
OnCell Search Utility
Configuration and Management Options:
Remote SMS Control, SNMPv1/v2c/v3, Web/Telnet/Serial
Console
Private IP Solution:
OnCell Central Manager
SIM Interface
Number of SIMs:
2
SIM Control:
3 V

OnCell 3470A-LTE Introduction
1-4
Physical Characteristics
Housing:
Aluminum, providing IP30 protection
Weight:
1300 g
Installation:
DIN-rail (default) or wall-mount (optional)
Dimensions:
67 x 90.5 x 124 mm (2.6 x 3.52 x 4.83 inch)
Environmental Limits
Operating Temperature:
Standard Models:
-30 to 55°C (-22 to 131°F)
Wide Temp. Models:
-30 to 70°C (-22 to 158°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity: 5 to 95% (30°C, non-condensing)
Power Requirements
Connector:
4-pin removable terminal block
Input Voltage:
12 to 48 VDC, redundant dual inputs
Power Consumption:
9.6W (12V/0.7A to 48V/0.2A)
Reverse Polarity Protection:
Present
Standards and Certifications
Safety:
OnCell G3470A-LTE-US: UL 60950-1
EMC:
OnCell G3470A
-LTE-US: FCC Part 15 Subpart B
OnCell G3470A
-LTE-EU: EN 61000-6-2/-4
Radio:
OnCell G3470A
-LTE-US: FCC ID N7NMC7355
OnCell G3470A
-LTE-EU: EN 301 489-1, EN 301 489-7, EN 301 511/4
Reliability
MTBF (mean time between failures):
327,326 hrs
Warranty
Warranty Period:
5 years
Details:
See www.moxa.com/warranty
ATTENTION
•
The OnCell G3470A-LTE
is NOT a portable mobile device and should be located at least 20 cm away from
the human body.
•
The OnCell G3470A-LTE is NOT designed for the general public. A well-trained technician should be
enlisted to ensure safe deployment of OnCell G3470A-LTE units, and to establish a wireless network.

OnCell 3470A-LTE Introduction
1-5
Functional Design
1. GPS antenna connector (female SMA)
2. Terminal block (two digital input and one digital relay)
3. Grounding screw (M5)
4. Terminal block (PWR1 and PWR2)
5. 2x2 MIMO antenna ports for LTE (female SMA)
6. RS-232 serial console (RJ45)
7. 10/100/1000 BaseT(X) Ethernet ports (RJ45)
8. LED display
9. DIN-rail mounting kit
10. Reset button
11. Dual SIM – SIM1
12. Dual SIM – SIM2

OnCell 3470A-LTE Introduction
1-6
LED Indicators
The LEDs on the front panel of the OnCell G3470A-LTE provide a quick and easy means of determining the
current operational status and wireless settings.
The following table summarizes how to read the device’s wireless settings from the LED displays. More
information is available in Chapter 3 in the “Basic Wireless Settings” section.
LED Color State Description
Front Panel LED Indicators (System)
PWR1 Green On Power is being supplied from power input 1
PWR2 Green On Power is being supplied from power input 2
READY Green On System startup is complete and the system is operating
Blinking Device has been located by the OnCell Search Utility
Off Power is off, or the system is booting up
FAULT Red On System configuration error or a relay event has occurred
Blink IP address conflict
Off Power is off, or there is no error condition.
CELLULAR
SIGNAL (3 LEDs)
Green On Number of LEDs to indicate cellular signal level when
registered to a base station.
Signal LED 1: 0 < RSSI ≤ 12
Signal LED 2: 12 < RSSI ≤ 21
Signal LED 3: 22 < RSSI ≤ 31
SIM1 Amber On/Off SIM 1 is active or inactive
Blink SIM 1 is not inserted or PIN code is incorrect
SIM2 Amber On/Off SIM 2 is active or inactive
Blink SIM 2 is not inserted or PIN code is incorrect
2G Amber On
Registered to a base station with cellular connection in GPRS
or EDGE mode
3G Amber On
Registered to a base station with cellular connection in UMTS
or HSPA mode
4G Amber On Registered to a base station with cellular connection in LTE
mode
GPS Green On GPS has been located
Blinking Locating GPS or less than four satellites have been located.
Off GPS has not been located.
LAN Port LED Indicators (Port Interface)
1000M Green On 1000Mbps link is active
Blink Data is being transmitted at 1000Mbps
Off 1000Mbps link is inactive
10/100M Amber On 10/100Mbps link is active
Blink Data is being transmitted at 10/100Mbps
Off 10/100Mbps link is inactive
ATTENTION
When the system fails to boot, the LEDs for
STATE (Green), FAULT, and WLAN will all light up
simultaneously and blink at one
-
second intervals. This may be due to improper operation or uncontrollable
issues, such as an unexpected shutdown while updating the firmware. To recover the firmware, refer to the
“Firmware Recovery” secti
on in Chapter 6.

OnCell 3470A-LTE Introduction
1-7
Beeper
The beeper emits two short beeps when the system is ready.
Reset Button
The RESET button is located on the bottom panel of the OnCell G3470A-LTE. You can reboot the OnCell
G3470A-LTE or reset it to factory default settings by pressing the RESET button with a pointed object such as
an unfolded paper clip.
•System reboot: Hold the RESET button down for under 5 seconds and then release.
•Reset to factory default: Hold the RESET button down for over 5 seconds until the STATE LED starts
blinking green. Release the button to reset the OnCell G3470A-LTE.

2
2. Getting Started
This chapter explains how to install Moxa’s OnCell G3470A-LTE for the first time, and quickly set up your
wireless network and test whether the connection is running well. The Function Map discussed in the third
section provides a convenient means of determining which functions you need to use.
The following topics are covered in this chapter:

First-time Installation and Configuration
Step 1: Inserting a SIM Card
Step 2: Turning on the OnCell G3470A-LTE
Step 3: Connecting the OnCell G3470A-LTE to a Computer
Step 4: Configuring the Computer’s IP Address
Step 5: Accessing the Web Console
Step 6: Establishing a Cellular Connection
Step 7: Verifying the Cellular Connection

OnCell 3470A-LTE Getting Started
2-2
First-time Installation and Configuration
Before installing the OnCell G3470A-LTE, make sure that all items in the package checklist are in the box. In
addition, you will need access to a notebook computer or PC equipped with an Ethernet port. The OnCell
G3470A-LTE has a default IP address that you must use when connecting to the device for the first time.
Step 1: Inserting a SIM Card
Insert one or two 2G/3G/4G SIM cards into the SIM slots located on the bottom of the OnCell G3470A-LTE.
Installing a SIM Card
The SIM card slots are i
nside the OnCell G3470A-LTE’s housing. To
install a SIM card, complete the following steps:
1. Turn off the OnCell G3470A-LTE.
2. Remove the screw to remove the SIM card slot cover.
3. Install a SIM card into a SIM card slot. Do the following:
a. For SIM 1, orient the gold contacts facing down and the cut-
off
edge to the left.
b. For SIM 2, orient the gold contacts facing up and the cut-
off
edge to the right.
4. Install the screw to secure the SIM card slot cover.
Step 2: Turning on the OnCell G3470A-LTE
Turn on the OnCell G3470A-LTE by connecting a power terminal block to a DC power source.
Step 3: Connecting the OnCell G3470A-LTE to a Computer
Since the OnCell G3470A-LTE supports MDI/MDI-X auto-sensing, you can use either a straight-through cable
or crossover cable to connect the OnCell G3470A-LTE to a computer. If the LED indicator on the OnCell
G3470A-LTE's LAN port lights up, it means a connection has been established.
Step 4: Configuring the Computer’s IP Address
Set an IP address on the same subnet as the OnCell G3470A-LTE. Since the OnCell G3470A-LTE’s default IP
address is 192.168.127.254, and the subnet mask is 255.255.255.0, you should set the IP address of the
computer to 192.168.127.xxx.
NOTE
After you select
Maintenance > Load Factory Default and click the Submit button, the OnCell
G3470A
-LTE will be reset to factory default settings and the IP address will be reset to 192.168.127.254.

OnCell 3470A-LTE Getting Started
2-3
Step 5: Accessing the Web Console
To access the web console:
1. Open a web browser.
2. Enter http://192.168.127.254 in the address field.
3. A login screen appears. Enter the user name (the default is “admin”) and password (the default is “root”);
then, click Login.
NOTE
Default user name and password:
User Name: admin
Password: root
For security reasons, we strongly recommend changing the default password. To do so, select Maintenance
>
Password, and then follow the on-screen instructions to change the password.
NOTE
After you click
Submit to apply changes the web page will refresh (Updated) will appear on the page
and a
blinking reminder will be shown on the upper
-right corner of the web page:
To activate the changes click
Restart and then Save and Restart
after you change the settings. About 30
seconds are needed for the
OnCell G3470A-LTE to complete the reboot procedure.
Step 6: Establishing a Cellular Connection
After installing a SIM card, obtain the SIM card PIN and APN (Access Point Name) information from your service
provider and configure the cellular WAN settings.
To configure cellular WAN settings and establish a cellular connection:
1. Log into the web console.
2. Click Cellular Settings > Cellular WAN Settings and enter the SIM card PIN and APN values.
3. Restart the OnCell G3740A-LTE. The OnCell 3740A-LTE automatically establishes a cellular connection to
the service provider.

OnCell 3470A-LTE Getting Started
2-4
Step 7: Verifying the Cellular Connection
You can use one of the following methods to verify the cellular connection:
1. Check the LED display.
Check the SIM 1, SIM2, 2G, 3G, and 4G LEDs on the front panel.
If a SIM LED is blinking, this indicates that a SIM card is not installed in the SIM slot or the SIM card PIN
information is not configured in the web console.
If the installed SIM card supports 3G or 4G service but only the 2G LED is turned on, this indicates that the
OnCell G3470A-LTE is connected to the cellular network but is not registered for 3G or 4G service. Make
sure that you enter the correct APN information in the web console.
2. Check the Overview screen in the web console.
Log into the web console and display the Overview screen. Check the status for the Cellular RSSI, Cellular
WAN IP address, and Cellular Mode fields to diagnose any connection problem.
For Cellular RSSI (Received Signal Strength Indication), make sure that the value is above 12 RSSI in order
to maintain a stable connection.
If the Cellular WAN IP address is not available but the RSSI is more than 12, make sure that the APN
configuration is correct. The service provider assigns a private address for the WAN IP address, which is not
accessible externally.
3. Test cellular network access on your computer.
For users with public SIM cards, instead of SIM cards with MDVPN service enabled, you can test the
connection to the Internet on your computer (assuming that your computer is connected to an Ethernet
port on the OnCell G3470A-LTE). The following shows an example configuration.
•Laptop IP Address: 192.168.127.10 (on the same subnet as the OnCell gateway)
•Laptop Subnet Mask: 255.255.255.0 (on the same subnet as the OnCell gateway)
•Laptop Default Gateway: 192.168.17.254 (the OnCell gateway IP address)
•Laptop Primary DNS Server: 8.8.8.8 (test with Google's public DNS server)
•Laptop Primary DNS Server: 8.8.4.4 (test with Google's public DNS server)
After the configuration is complete, your computer will be able to the access the Internet.
For information on testing the connection with a DHCP server, refer to Chapter 3.

3
3. Web Console Configuration
This chapter describes the web console that you can use to configure your OnCell G3470A-LTE and set up a
wireless network.
The following topics are covered in this chapter:

Accessing the Web Console
Configuration Menu Overview

Overview

Basic Settings
System Info Settings
Network Settings
Time Settings

Cellular Settings
Cellular WAN Settings
GuaranLink
Auto IP Report Settings
GPS Settings
Oncell Central Manager Setting

Advanced Settings
DHCP Server (for AP mode only)
DDNS
Packet Filters
SNMP Agent
Port Forwarding
VPN

Auto Warning Settings
System Log
Syslog
E-Mail
Relay
Trap
SMS

Status
DNS Information
SIM Status
Network Statistics
Routing Table
DHCP Client List (for AP mode only)
System Log
Relay Status
DI and Power Status
VPN Log

Maintenance
Console Settings
Ping
Firmware Upgrade
Config Import Export
Load Factory Default
Password
Misc. Settings
Manual SMS
Remote SMS Control

Save Configuration

Restart

Logout

OnCell 3470A-LTE Web Console Configuration
3-2
Accessing the Web Console
Moxa OnCell G3470A-LTE’s web browser interface provides a convenient way to modify its configuration and
access the built-in monitoring and network administration functions. The recommended web browser is
Microsoft®Internet Explorer 7.0 or 8.0 with JVM (Java Virtual Machine) installed.
NOTE
To use the OnCell G3470A
-LTE’s management and monitoring functions from a PC host connected to the
same LAN as the OnCell G3470A
-LTE, you must make sure that the PC host and the OnCell G3470A-
LTE are
on the same logical subnet.
The Moxa OnCell G3470A
-LTE’s default IP is 192.168.127.254.
Follow these steps to access the OnCell G3470A-LTE’s web-based console management interface.
1. Open your web browser (e.g., Internet Explorer) and type the OnCell G3470A-LTE’s IP address in the
address field; then, press [Enter].
2. The login page appears. Enter the password (the default username is “admin” and the default password is
“root”) and click Login.
It may take a few moments for the web page to load on your computer. Note that the Model name and IP
address of your OnCell G3470A-LTE are both shown on the title bar of the web page. You can use this
information to identify multiple OnCell G3470A-LTE units.
3. Use the menu navigation panel to access the configuration screens.
In the following sections, we describe each OnCell G3470A-LTE management function in detail. For an overview
of the menus, refer to the “Function Map” section of Chapter 2.
NOTE
The mode
l name of the OnCell G3470A-LTE is shown as OnCell G3470A-LTE-XX, where XX indicates the
country code. The country code indicates the OnCell G3470A
-LTE version and which bandwidth it uses.
Example figures shown in this document are for OnCell G3470A
-LTE-US. The country code and model name
that appear on your computer screen may be different than the one shown here.

OnCell 3470A-LTE Web Console Configuration
3-3
Configuration Menu Overview
Advanced features to support additional network management
and secure wired and wireless communication.
Note: These advanced functions are all optional.
Application-oriented device management functions to set up
events, traps, and reactions via relay warning, e-mail, and SNMP
notification.
Note: These functions are all optional.
Current status information for monitoring wired/wireless network
performance, advanced services, and device management
functions.
On-demand functions to support the web console
management operation.
Essential settings related to establishing a cellular network.
Quick overview of the OnCell G3470A-LTE’s status.
Basic settings for administering the OnCell G3470A-LTE.
Functions for maintaining the OnCell G3470A-LTE, and for
diagnosing the network.

OnCell 3470A-LTE Web Console Configuration
3-4
Overview
The Overview page provides a summary of the OnCell G3470A-LTE’s current status. The information is
categorized into groups: System Info, LAN Info, and Cellular Info.
Basic Settings
The Basic Settings group includes the most commonly used settings required by administrators to maintain and
control the OnCell G3470A-LTE.
System Info Settings
The System Info items, especially Device name and Device description, are displayed and included on the
Overview page, in SNMP information, and in alarm emails. Setting System Info items makes it easier to
identify the different OnCell G3470A-LTE units connected to your network.
Field Description Default setting
Device name Enter a descriptive name (up to 31 characters).
This option is useful for specifying the role or application of different
OnCell G3470A-LTE units.
OnCell
G3470A-LTE_[serial
no]
Device location Specify the location (up to 31 characters) of the OnCell G3470A-
LTE.
Device
description
Enter a description (up to 31 characters) for the OnCell G3470A-LTE.
Device contact
information
Enter the contact information (up to 31 characters) of the person
responsible for maintaining this OnCell G3470A-LTE.

OnCell 3470A-LTE Web Console Configuration
3-5
Network Settings
You can use the Network Settings screen to configure TCP/IP settings.
Field Description Default setting
IP address Enter the unique IP address for the OnCell G3470A-LTE. 192.168.127.254
Subnet mask
Enter the subnet mask to specify the type of network to which the
OnCell G3470A-LTE is connected.
255.255.255.0
Primary/Secondary
DNS server
Enter the IP address of the primary or secondary DNS server.
After you specify a DNS server, you can access a web site by
entering its URL instead of the IP address.
Time Settings
You can synchronize the system time on the OnCell G3470A-LTE based on an NTP (Network Time Protocol)
server or user-specified date and time information. The OnCell G3470A-LTE includes the system time in system
logs.
NOTE
The OnCell G3470A
-LTE includes a built-in real time clock (RTC). We strongly recommend that you
update the
Current local time
for the OnCell G3470A-LTE after the initial setup or a long-term shutdown, especially
when the network does not have an Internet connection for
accessing the NTP server or if there is no NTP
server on the LAN.
Field Description Default setting
Current local
time
The fields indicate the current system time on the OnCell
G3470A-LTE.
Enter the date and time in the format yyyy/mm/dd hh:mm:ss
To make the changes take effect, click Set Time. An “Updated” text
appears to indicate that the change is complete.
Note
: Set the time zone before you configure the current local time.