Moxa Technologies AIG-100 Series User manual

P/N: 1802001017010
*1802001017010*
AIG-100 Series
Quick Installation Guide
Version 1.0, October 2022
Technical Support Contact Information
www.moxa.com/support

2022 Moxa Inc. All rights reserved.

- 2 -
Overview
Moxa AIG-100 Series can be used as smart edge gateways for data
preprocessing and transmission. The AIG-100 Series focuses on IIoT-
related energy applications and supports various LTE bands and
protocols.
Package Checklist
Before installing the AIG-100, verify that the package contains the
following items:
•AIG-100 gateway
•DIN-rail mounting kit (preinstalled)
•Power jack
•3-pin terminal block for power
•Quick installation guide (printed)
•Warranty card
NOTE
Notify your sales representative if any of the above items are
missing or damaged.
Panel Layout
The following figures show the panel layouts of the AIG-100 models:
AIG-101-T

- 3 -
AIG-101-T-AP/EU/US
LED Indicators
LED Name
Status
Function
SYS
Green
Power is ON
Off
Power is OFF
Green
(blinking)
The gateway will reset to the default
configuration
LAN1/LAN2
Green
10/100 Mbps Ethernet mode
Off
Ethernet port is not active
COM1/COM2
Orange
Serial port is transmitting or receiving data
LTE
Green
Cellular connection has been established
NOTE:
Three levels based on the signal strength
1 LED is ON: Poor signal quality
2 LEDs are ON: Good signal quality
All 3 LEDs are ON: Excellent signal quality
Off
Cellular interface is not active
Reset Button
Reboots or restores the AIG-100 to factory default settings. Use a
pointed object, such as a straightened paper clip, to activate this
button.
•System reboot: Press and hold the Reset button for one second or
less.
•Reset to the default configuration: Press and hold the Reset button
till the SYS LED blinks (approximately seven seconds).

- 4 -
Installing the AIG-100
The AIG-100 can be mounted on to a DIN rail or on to a wall. The DIN-
rail mounting kit is attached by default. To order a wall-mounting kit,
contact a Moxa sales representative.
DIN-rail Mounting
To mount the AIG-100 on to a DIN rail, do the following:
1. Pull down the slider of the DIN-rail bracket at the back of the unit
2. Insert the top of the DIN rail into the slot just below the upper
hook of the DIN-rail bracket.
3. Latch the unit firmly on to the DIN rail as shown in the illustrations
below.
4. Once the computer is mounted properly, you will hear a click and
the slider will rebound back into place automatically.
Wall Mounting (optional)
The AIG-100 can also be wall mounted. The wall-mounting kit needs to
be purchased separately. Refer to the datasheet for more information.
1. Fasten the wall-mounting kit to the AIG-100 as shown below:
2. Use two screws to mount the AIG-100 on to a wall.
These two screws are not included in the wall-mounting kit and

- 5 -
must be purchased separately. Refer to the detailed specifications
below:
Head Type
:flat
Head Diameter
>5.2 mm
Length
>6 mm
Thread Size
:M3 x 0.5 mm
Connector Description
Power Terminal Block
A person trained for the job should install the wiring for the input
terminal block. The wire type should be copper (Cu) and only 28-18
AWG wire size and torque value 0.5 N-m should be used.
Power Jack
Connect the power jack (in the package) to the AIG-100’s DC terminal
block (on the bottom panel), and then connect the power adapter. It
takes several seconds for the system to boot up. Once the system is
ready, the SYS LED will light up.
NOTE
The product is intended to be supplied by a UL Listed Power
Unit marked "L.P.S." (or "Limited Power Source") and is rated
9
-36 VDC, 0.8 A min., Tma = 70°C (min). If you need further
help
with purchasing the power source, please contact Moxa for
further information.
Grounding
Grounding and wire routing help limit the effects of noise because of
electromagnetic interference (EMI). There are two ways to connect the
AIG-100 grounding wire to the ground.
1. Through the SG (Shielded Ground):
The SG contact is the left-most contact in the
3-pin power terminal block connector when
viewed from the angle shown here. When you
connect to the SG contact, the noise will be
routed through the PCB and the PCB copper
pillar to the metal chassis.
2. Through the GS (Grounding Screw):
The GS is next to the power connector. When
you connect to the GS wire, the noise is
routed directly through the metal chassis.
NOTE
The grounding wire should have a minimum diameter of
3.31 mm
2
.

- 6 -
NOTE
If using a Class I adapter, the power cord must be connected to
a socket-outlet with an earthing connection.
Ethernet Port
The 10/100 Mbps Ethernet port uses the RJ45 connector. The pin
assignment of the port is as below:
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
4
–
5
–
6
Rx-
7
–
8
–
Serial Port
The serial port uses the DB9 male connector. Software can configure it
for the RS-232, RS-422, or RS-485 mode. The pin assignment of the
port is as below:
Pin
RS-232
RS-422
RS-485
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
SIM Card Socket
The AIG-100-T-AP/EU/US comes with two nano-SIM card sockets for
cellular communication. The nano-SIM card sockets are on the same
side as the antenna panel. To install the cards, remove the screw and
the protection cover to access the sockets, and then insert the nano-
SIM cards into the sockets directly. You will hear a click when the cards
are in place. The left socket is for SIM 1 and the right socket is for SIM
2. To remove the cards, push the cards in before releasing them.
RF Connectors
The AIG-100 comes with RF connectors to the following interfaces.

- 7 -
Cellular
The AIG-100-T-AP/EU/US models come with a built-in cellular module.
You must connect the antenna to the SMA connector before you can
use the cellular function. The C1 and C2 connectors are interfaces to
the cellular module. For additional details, refer to the AIG-100 Series
datasheet.
GPS
The AIG-100-T-AP/EU/US models come with a built-in GPS module. You
must connect the antenna to the SMA connector with the GPS mark
before you can use the GPS function.
SD Card Socket
The AIG-100 models come with a SD-card socket for storage
expansion. The SD card socket is next to the Ethernet port. To install
the SD card, remove the screw and the protection cover to access the
socket, and then insert the SD card into the socket. You will hear a click
when the card is in place. To remove the card, push the card in before
releasing it.
USB
The USB port is a type-A USB 2.0 port, which can be connected to Moxa
UPort models to extend the serial port capacity.
Real-time Clock
A lithium battery powers the real-time clock. We strongly recommend
that you do not replace the lithium battery without the help of a Moxa
support engineer. If you need to change the battery, contact the Moxa
RMA service team.
ATTENTION
There is
a risk of explosion if the battery is replaced with an
incorrect type
of battery. Dispose of
used batteries according to
the instructions in the warranty card.
Access to the Web Console
You can log in to the web console by default IP through the web
browser. Please ensure your host and AIG are under the same subnet.
•LAN1: https://192.168.126.100:8443
•LAN2: https://192.168.127.100:8443
When you log in to the web console, the default account and password:
•Default account: admin
•Default password: admin@123