Moxa Technologies FLI-1200 Series User manual

– 1 – – 2 – – 3 –
P/N: 1802012600001
FLI-1200 Series
Quick Installation Guide
First Edition, November 2014
Overview
Moxa’s FLI-1200 is an industrial auto-configuration server
appliance designed to automatically configure and monitor various
Moxa products in harsh industrial environments.
The FLI-1200 has a fanless, thermally efficient, dust- and
water-protected IP54-rated chassis. The sealed enclosure protects
the internal components from dust and splashed water, and is
compliant with the EN 50155 standard, covering operating
temperature, power input voltage, power surges, ESD, and
vibration, ensuring that the FLI-1200 can operate reliably under
extreme environments for rolling stock applications.
The FLI-1200 comes with Moxa’s FLI technology, which ensures
that the replacement or deployment of any Moxa device will not
affect the existing architecture, and eliminates the need to
perform manual reentry or reconfiguration. With its web-based
interface, users can easily manage the system and monitor the
status of any device being controlled by the FLI-1200, and its
reliable and robust design ensures that when the primary FLI
server is offline, the backup server will take over to keep the
auto-configuration functionality up and running. With the FLI-1200,
users can maintain Moxa’s products more efficiently, and realize a
considerable reduction in maintenance costs and human error.
Package Checklist
Before installing the FLI-1200, verify that the package contains the
following items:
•FLI-1200 auto-configuration server appliance
•Wall mounting kit
•Quick installation guide (printed)
•Warranty card
NOTE: Please notify your sales representative if any of the above
items are missing or damaged.
FLI-1200 Panel Layout
Front View
Rear View
LED Indicators
The following table describes the LED indicators located on the
front panel of the FLI-1200.
LED Name
LED Color/
Status
LED Function
Ready
Green
System is ready
Blinking
once per
second
Reset to default
Off
System is not ready
LAN (1, 2)
Green,
blinking
100 Mbps Ethernet mode
Off
No Ethernet activity or operating at 10
Mbps
Act.
Red This FLI-1200 is acting as the master
FLI server
Off
This FLI-1200 is not acting as master
FLI server
Installing the FLI-1200
The
FLI-1200 comes with
two brackets
for mounting it
on walls
. Use two screws
on
each
side to attach the
FLI
-1200 to a wall or
cabinet.
The FLI
-1200 also comes
with
an optional rack
installation kit. Simply slide
the FLI
-1200 into the rack
mounting bracket
to
complete
the installation.
Refer to the
FLI-1200
Hardware
Manual for
more
detailed installation
instructions.
Connector Description
Ethernet Ports
Two 10/100 Mbps Ethernet ports using M12 D-coded connectors
are located on the front panel. The pin assignments are shown in
the following figure and table.
Configuring Power Inputs
One 24 VDC power input using a 5-pin M12 connector is located on
the front panel. The pin assignments are shown in the following
figure and table.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2014 Moxa Inc., All Rights Reserved
Digital Input M12 Pin Assignment
Two DIs using M12 A-coded connectors are located on the rear
panel. The pin assignments are shown in the following figure and
table.
PIN
DIO
1
–
2
–
3
GND
4
DI_1
5
–
6
DI_0
7
DI_SOURCE
8
–
Reset to Default
Use a screwdriver to push in the Reset to Default button on the
rear panel, and then hold it for five seconds. The system will reset
all software settings to their factory default values.
Real-Time Clock
The FLI-1200’s real-time clock is powered by a lithium battery. We
strongly recommend that you do not replace the lithium battery
without help from a qualified Moxa support engineer. If you need
to change the battery, contact the Moxa RMA service team.
WARNING
There is a risk of explosion if the battery is replaced with a
battery that does not have the correct specifications.
Powering Up the FLI-1200
To power on the FLI-1200, connect it to a 24 VDC power source, or
to any Ethernet switch that supports PoE or PoE+. Once the system
is powered and initialized, the Ready LED will light up.