Moxa Technologies EtherDevice EDS-4012 Series User manual

P/ N : 1 8 0 20 4 0 1 2 001 0
*1802040120010*
EDS-4012 Se r ie s
Quick I nst a lla t ion Guid e
M ox a Et h e r De vice ™ Sw it ch
Ve rsion 1 .0 , M a rch 2022
Techn ica l Sup por t Con tact I n for m at io n
w w w .m oxa . com / supp ort

2022 Moxa I nc. All r ight s r eserv ed.

- 2 -
Pa ck age Che ck list
The EDS-4012 Series in dust rial DI N- rail EtherDevice Sw it ch ( EDS) is
shipped wit h the follow ing it em s. I f any of these it em s are m issin g or
dam aged, please con tact y ou r cu st om er ser vice r epresen tat iv e f or
assist an ce.
• 1 EDS-4012 Ethernet sw it ch
• Quick inst allat ion guide ( p rin t ed )
• Warr ant y card
• Su bst an ce disclosur e table
• Product cert ificate of qualit y inspect ion ( Sim plified Chinese)
• Product not ices ( Sim plified Chin ese)
N OT E
You can find infor m ation an d soft w are downloads on t he
relevant product pages lo
cat ed on Moxa’s website:
w ww .m oxa. com
D e fa u lt Se t t in gs
• I P addr ess: 1 92.168.1 27.253
• Subnet Mask: 255.255.2 55.0
• User nam e: adm in
• Passw or d: m oxa
Pa ne l Vie w s of ED S-4 0 1 2 Se rie s
1. 100BaseT( X) LED in dicat or
2. 10BaseT( X) LED in dicat or
3. 10/ 1 00 BaseT( X) por t s, por t s
1 t o 8
4. 10/ 100/ 1000BaseT(X) or
100/ 1000BaseSFP com b o
por t s, por t s G1 t o G4
5. 100/1000BaseSFP LED
indicator
6. 100/ 1000BaseSFP ports,
por t s G1 t o G4
8.
Ter m inal bl ock s f or p ow er in pu t ,
digital input , and relay out put
9. LED indicat ors: STATE ( S),
FAULT ( F) , PWR1 ( P1) , PWR2
( P2) , MSTR/ HEAD ( M/ H) ,
CPLR/ TAI L ( C/ T) , SYNC
10.
Con sole por t ( RJ4 5, RS-232)
11.
USB st or age por t ( t ype A,
cu rr en t ly di sab led)
12.
Model na m e

- 3 -
7. Grounding connect or scr ew
13. Sm ar t PoE LED in dicat or of PoE
por t s
Bo t tom Pa n el Vie w
1. m icr oSD car d slot
( cu rr en t ly di sabl ed)
2. Reset but t on
3.
DI P sw it ches for Turbo
Rin g, Ring Ma st er , an d
Ring Cou pler
M ou n t in g Di m e n sio n s

- 4 -
D I N - ra il M ou n t in g
The DI N-rail m ou nt ing kit is fixed t o the back panel of t he EDS device
when you t ake it out of t he box. Mount the EDS device on cor rosion-
fr ee m ou nt in g r ails t hat m eet t he EN 60 71 5 st an dar d.
I nst a lla t ion
STEP 1 —I n ser t t h e u pper lip of
t he DI N r
ail in t o t he DI N- rail
m ount in g kit
.
STEP 2
—Press the EDS device
towar ds the
DI N rail unt il it
snaps int o place.
Re m o v a l
STEP 1
—
Pull dow n t he lat ch on
t he m ount in g kit w it h a
scr ewdriver.
STEP 2
& 3 —Slight ly pull t he
EDS device forward and lift up
to rem ove it from the DI N rail.
N OT E
Our DI N rail
kit
n ow ut ilizes a quick r elease m ech an ism t o m ak e
it easier for user s t o rem ove the DI N rail fr om the EDS device.

- 5 -
W a l l M ou n t in g ( Opt io na l )
For so m e applicat ions, y ou w ill fin d it con ven ien t t o m ou nt t he Moxa
EDS device on a wall, as shown in t he follow ing illust r at ions:
STEP 1 —Rem o ve t h e DI N-rail
at t achm ent pl
at e fr om t he r ear
panel of t he EDS device,
as
illust rated
in t he diagr am on
the
r ig ht .
STEP 2 —Mounting t he EDS device on a w all
requires
six scr ew s. Use t he EDS device, wit h wall
m ount plat es at t ach ed, as a guide t o m ar k t he
cor r ect locat ion s of t h e
six scr ew s. T
he heads of t he
screws should be less t han 6.0 m m in diam et er,
and t he shaft s should be less t han 3.5
m m in
di am et er , as sh ow n in t he figur e on at r ight .
N OT E
Befor e tight ening t he screws into t he w all, m ake sure the screw
head and shank size are suitable by insert ing the scr ew through
one of t he keyhole
-shaped apert ur es of t he Wall Mount ing
Plates.
N OT E
Do not scr ew the screw s in all t he way—leave about 2 m m t o
allow room for sliding t he w all m ount panel bet w een the w all
an d t he scr ew s.
STEP 3 —On ce t he scr ew s ar e
fixed
to t he wall, inser t t he
four screw heads t hrough the
wide parts of t he keyhole
-
shaped apert ures, and then
slide
the EDS device
dow nw ards, as indicated
in
the figure
at t h e r ight .
Tighten the four scr ews for
m or e
st abilit y.

- 6 -
W i ri ng Re qu ir e m e nt s
ATTEN TI ON
Sa f e t y Fir st !
Ext er nal m et al par t s ar e h ot . Take
the n ecessar y pr ecau t ion s if
you are required t o handle the device.
ATTEN TI ON
I n or der to ensure reliable oper ations, please m ake sure the
oper at in g t em p er at ur e of t he en vironm ent does not exceed t he
specificat ion s. When m ount ing an EDS device wit h ot her
operat ing unit s in a cabinet w it hou t forced vent ilat ion, a
m in im u m of
4 cm spac
e on both t he left and right of t he sw it ch
is r ecom m en ded.
ATTEN TI ON
Sa f e t y Fir st !
Be sure t o disconnect the pow er cord befor e inst alling and/ or
w ir ing your EDS dev ice. Cal culat e t he m ax im u m possib le
current in each
pow er w ir e and com m on w ir e. Ob ser ve all
elect rical codes dict at in g t h e m axim um cur rent allow ab le for
each wire size. I f t he current goes above the m axim um r atings,
t he w ir in g cou ld over heat , cau sin g ser iou s dam ag e t o your
equip m en t .
Be sur e t o r ead and follow t h ese im por t ant p oin t s b elow :
• Use separ at e pat hs t o rout e w ir in g for pow er an d devices. I f pow er
wiring and device w ir ing path s m ust cr oss, m ake sur e t he wires are
per pendicular at the int er section point .
N OT E
Do not r un si gn al or com m unicat ions wir ing an d pow er w ir ing
t hr ou gh t he sam e w ir e condu it . To av oi d in t er ference, w ir es
with differ ent signal charact erist ics should be rout ed separat ely.
• You can use t he t ype of signal t ransm itted t hr ough a w ire to
det er m ine w hich w ir es should be k ep t separate. The r ule of t hum b
is t hat w ir in g that shar es sim ilar elect rical char act er ist ics can be
bu ndled t oget her .
• You should separat e input w iring from out put wir ing.
• We advise that you label t he wirin g t o all devices in y our sy st em .

- 7 -
Gr ou n di ng t h e M ox a ED S Se rie s
Grounding and wire r out ing help lim it t he effect s of noise due t o
elect rom agn et ic in t er fer ence ( EMI ) . Run t he gr ou nd con nect ion fr om
the ground screw t o t he grounding surface prior to connect ing devices.
ATTEN TI ON
This product is int ended to be m ount ed t o a well
-gr ounded
m ount in g sur face su ch as a m et al panel.
Sugge st e d W ire Type for W ir ing Re la y Cont a ct
( RELAY) , Digit a l I n pu t ( D I ) , a nd Pow e r I n put s
( P1 / P2 )
The EDS device includes t w o 4-pin s 3. 5 m m pin -pit ch t er m inal b lo ck s.
Wh en w ir in g t h e r elay cont act ( RELAY) , digit al in pu t ( DI ) , an d pow er
input s ( P1/ P2) , w e su ggest using t he cable t ype AWG 18-24 and t he
cor respon din g pin t ype cable t er m inals.
N OT E
The w ir e m u st be
able t o w it hst and at least 105°C an d t h e
torque value should be 4.5 lb-in ( 0 .5 1 N-m ) .
N OT E
W
e su gg est t h e lengt h of t h e pin t y pe ca bl e t er m in al is 8 m m .
I
n or der t o t igh t en t h e w ir e pr op er ly , ①use a sm all flat head
scr ew d ri ver t o pr ess t h e pu sh
-
in but t on beside each t er m inal of
t he t er m inal block con nect or befor e an d d ur in g
②
inser ting the
wire.
③Release the screwdriver aft er t he wire has been fully
inser t
ed. Please refer t o the diagram below.
W i ri ng t h e Re la y Con t a ct
The EDS device has on e set of r elay ou t pu t. This relay cont act uses t w o
con tact s of t he t er m in al block on the EDS’s pow er m odule. Refer t o t he
sect ion for det ailed in st ruct ion s on how t o connect t he wires t o t he
t er m inal block con nect or , an d how t o at t ach t he t er m in al block
con nect or t o t he t er m in al block r ecept or .

- 8 -
Re l a y:
The two cont act s of
the 4 - pin t er m in al
block connect or are used t o det ect
user
-configured events. The tw o wir es
at t
ached t o t he fau lt con tact s for m an
open cir cui
t when a u ser-configured
event is tr igger ed or
there is no power
su pp ly t o t h e sw it ch
. I f a user -
configur ed event does n ot occur , t he
fault circuit rem ains closed.
W i ri ng t h e Re d un da n t Pow e r I n pu t s
The EDS device includes b ot h high-v ol t ag e an d low -v olt age pr oduct s.
For t h e low -volt age ( LV m odels) product s, t here are t w o power input s
for redundancy; for the high-v olt age ( HV m od els) pr odu ct s, t h er e is
only one pow er input. Refer t o t he in str uct ions an d diagram below on
how t o connect t he wires t o t he t er m inal block connect or on t he
recept or.
STEP 1 : I nsert t he Posit ive/ Negat iv e
DC or Line/ Neu tr al AC w ir es in t o t he
V+ / V
- or L/ N t er m in als, r espect iv el y.
STEP 2 :
To keep the DC or AC w ir es
fr om pulling l
oose, u se a sm all f lat -
bl ade scr ew dr iv er t o t ig ht en t he w ir e
-
clam p scr ew s on t he fr ont of t he
t er m in al bl ock con nect or .
STEP 3 :
I n ser t t h e plast ic t er m inal
bl ock con nect or p ron gs in t o t h e
t er m inal bl ock r ecept or , which is
locat ed on the EDS devices’ right side.

- 9 -
W i ri ng t h e D ig it a l I n pu t s
The EDS device has one set of digit al input ( DI ) . Th e DI con sist s o f t w o
con t act s o f t he 4 - pin t erm inal block connect or on t he EDS's right -side
panel. Refer to t he inst r uct ions and diagr am below on how t o connect
the w ir es t o t he t er m in al block con nect or on t he recept or .
STEP 1 :
I nsert t he negat ive
(ground) / positive DI w ir es int o the
┴
/ I t er m in als, respectively.
STEP 2 :
To keep the DI wires from
pu llin g loose, use a sm all f lat
-blade
scr ew dr iver t o t ight en t he w ir e
-clam p
but t on
on t he fr on t of t he t er m inal
bl ock con nect or .
STEP 3 :
I n ser t t h e plast ic t er m inal
bl ock con nect or p ron gs in t o t h e
t er m inal bl ock r ecept or , which is
locat ed on the EDS devices’ right side.
Rot a t in g t h e Po w e r M od ule
The power m odule for t he EDS device can be r otated to m ake it easier
to fit y our field site applicat ion.
St ep 1 :
Rem ov e t he t w o scr ew s t hat fast en t h e p ow er m od ul e t o the
EDS device
and r em ove t he m odule.
St ep 2 :
Turn t he power m odule clockwise so t hat t he power , digit al
input
, and r elay ou tpu t con nect or s can be m oved u pw ar ds.
St ep 3 :
Rep lace t he m od ule back
on to t he EDS device.
St ep 4 :
Fast en t w o scr ew s on to t he m odule.

- 10 -
Com m un ica t ion Con ne ct ion s
Each EDS-4012 Ser ies swit ch h as var ious t y pes of com m u nicat ion
por t s:
• RJ45 console por t ( RS-232 int erface)
• USB st or age por t ( t ype A connect or , cu rren tly disabled)
• 10/100BaseT( X) Ethernet por t s
• 10/ 100/ 1 00 0BaseT( X) or 1 00 / 1 00 0BaseSFP com b o p or t s
• 100/1000BaseSFP slot s
• m icr oSD car d slot ( cu r ren t ly d isab led )
Con so le Po r t Co nn e ct i on
The EDS device has one RJ45 con sole por t ( RS-232), located on t he
front panel. Use eit her an RJ45-t o-DB9 ( see t he cable following wiring
diagr am s) t o connect the EDS’s con sole p or t t o y ou r PC’s COM p or t .
You m ay t hen u se a console t er m inal pr ogram , su ch as Moxa PCom m
Ter m in al Em ulat or , t o access t h e EDS that has a bau d rat e of 1152 00.
RJ4 5 Console Por t Pinou ts
Pin
De script ion
1
DSR
2
RTS
3
–
4
TxD
5
RxD
6
GND
7
CTS
8
DTR
USB Con ne ct ion
N OT E
The USB funct ion is cur ren tly r eser ved and m ay be r equ ir ed in
the fut ure. I t should be not ed t hat t his port cannot be u sed for
charging any devices.
1 0 / 1 0 0 BaseT( X) Et hernet Por t Con n ect ion
The 1 0/ 1 00BaseT( X) por t s locat ed on t he fron t panel of t he sw it ch ar e
used t o connect t o Ethernet-enab led dev ices. Most u ser s w ill ch oo se t o
configure t hese por t s for Auto MDI / MDI -X m ode, in w hich case t he
por t ’s pinout s are adj ust ed aut om at ically depending on t he t ype of
Ethernet cable used ( straight-t hrough or cross-ov er ) , an d t h e t y pe of
de vice ( NI C-t y pe or HUB/ Sw it ch -t ype) that is con nect ed t o t he por t .
I n t he followin g, we give pinout s for both MDI ( NI C-t ype) por t s an d
MDI -X ( HUB/ Sw it ch -t y pe) p or t s. We also give cable wiring diagram s for
st raight -t hrough and cross-ov er Et her net cables.
1 0 / 1 0 0 Ba se T( x ) RJ4 5 Pi nou ts
M DI Po rt Pin ou t s
MDI -X Por t Pinou t s
8 - pin RJ4 5
Pin
Sig na l
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Sig na l
1
Rx+
2
Rx-
3
Tx+
6
Tx-