Moxa Technologies EtherDevice EDS-510A-3GT Manual

2014 Moxa Inc. All rights reserved.
P/N: 1802005100015
EDS-510A
Hardware Installation Guide
Moxa EtherDevice™ Switch
Eighth Edition, April 2014

- 2 -
Package Checklist
The EDS-510A is shipped with the following items. If any of these items
are missing or damaged, please contact your customer service
representative for assistance.
•1 EDS-510A EtherDevice Switch
•Hardware Installation Guide (this guide)
•CD-ROM with user’s manual and Windows utility
•Moxa product warranty statement
•RJ45 to DB9 console port cable
•Protective caps for unused ports
•DIN-Rail mounting kit (attached to the EDS-510A’s rear panel by
default)
Optional Accessories
•SFP-1GSXLC: Small Form factor Pluggable transceiver with
1000BaseSX, LC, 0.5km, 0 to 60°C
•SFP-1GSXLC-T: Small Form factor Pluggable transceiver with
1000BaseSX, LC, 0.5km, 20 to 75°C
•SFP-1GLXLC: Small Form factor Pluggable transceiver with
1000BaseLX, LC, 10km, 0 to 60°C
•SFP-1GLXLC-T: Small Form factor Pluggable transceiver with
1000BaseLX, LC, 10km, -40 to 75°C
•SFP-1GLHXLC: Small Form factor Pluggable transceiver with
1000BaseLHX, LC, 40 km, 0 to 60°C
•SFP-1GLHXLC-T: Small Form factor Pluggable transceiver with
1000BaseLHX, LC, 40 km, -40 to 75°C
•SFP-1GZXLC: Small Form factor Pluggable transceiver with
1000BaseZX, 80 km, LC, 0 to 60°C
•ABC-01: Automatic Backup Configurator via RS-232 Console Port, 0
to 60°C
•DR-4524—DIN-Rail Power Supply (24 VDC, 45W/2A, with 85 to 264
VAC input)
•DR-75-24—DIN-Rail Power Supply (24 VDC, 75W/3.2A, with 85 to
264 VAC input)
•DR-120-24—DIN-Rail Power Supply (24 VDC, 120W/5A, with 88 to
132 VAC/176 to 264 VAC input by switch)
•EDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server
software and user’s manual
•WK-46—Wall Mounting Kit (will be shipped with the product)
•RK-4U—4U-high 19" rack mounting kit

- 3 -
Panel Views of EDS-510A
1. 1 to 7: 10/100BaseT(X) port
2. G1:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
10/100/1000BaseT(X) port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
3. G2:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
1000BaseSX/LX/LHX/ZX port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
4. G3:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
1000BaseSX/LX/LHX/ZX port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
5. G1, G2, G3: LED indicators for
1000 Mbps ports
6. PWR1: LED for power input 1
7. PWR2: LED for power input 2
8. FAULT: LED indicator
9. MSTR/HEAD: LED indicator
10.
CPLR/TAIL: LED indicator
11.
100M: LED indicator for TP port
12.
10M: LED indicator for TP port
13.
Model Name

- 4 -
Top Panel:
1. Ground screw
2. RS-232 console port
3. Heat dissipation orifices
4. DIP switches for Ring Master, Ring
Coupler, and Turbo Ring
5. 6-pin terminal block for
DI 1, DI 2,
and PWR 2
6. 6-pin terminal block for PWR1,
Relay 1, and Relay 2
Rear Panel:
1. Screw holes for Wall Mounting Kit
2. DIN-Rail Kit
Mounting Dimensions
Unit = mm (inch)

- 5 -
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of the EDS-510A when you take it out of the box. If you need
to reattach the DIN-Rail attachment plate to the EDS-510A, make sure
the stiff metal spring is situated towards the top, as shown by the
following figures.
STEP 1
—
Insert the top of the
DIN
-Rail into the slot just below the
stiff metal spring.
STEP 2
—
The DIN-Rail attachment
unit will snap into place as shown
in
the following illustration.
To remove the EDS-510A from the DIN-Rail, simply reverse Steps 1 and
2 above.
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa
EDS-510A on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN
-Rail
attachment plate from the
rear panel
of the EDS-510A
,
and then attach the wall
mount plates
with M3
screws
, as shown in the
figure
at the right.
STEP 2—Mounting the EDS-510A on the wall requires
4 screws. Use the
EDS-510A, with wall mount plates
attached, as a guide to mark the correct locations of
the 4 screws. The heads of the screws should be less
than 6.0 mm in diameter, and the shafts should be less
than 3.5
mm in diameter, as shown in the figure on a
t
right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.

- 6 -
STEP 3—Once the screws are fixed
to
the wall, insert the four screw
heads through the wide parts of the
keyhole
-
shaped apertures, and then
slide
the EDS-510A downwards, as
indicate
d in the figure at the right.
Tighten the four screws for
more
stability
.
ATEX Information
1. Certificate number DEMKO 08 ATEX 0810937x
2. Ambient range (-40°C ≤Tamb ≤75°C)
3. Certification string (Ex nA nC IIC T4 Gc)
4. Standards covered ( EN 60079-0:2012, EN60079-15:2010)
5. The conditions of safe usage:
•These products must be mounted in an IP54 enclosure.
•Install in an area of pollution degree 2 or less.
•Use a conductor wire of size 0.2 mm² or greater.
•PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE
APPARATUS, TO PREVENT THE RATED VOLTAGE BEING
EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE
THAN 40 %
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to
be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
S
afety Extra-Low V
oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
S
afety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
ATTENTION
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the
unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).

- 7 -
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together
•You should separate input wiring from output wiring
•We advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-510A
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.

- 8 -
Wiring the Relay Contact
The EDS-510A has two sets of relay outputs—relay 1 and relay 2. Each
relay contact uses two contacts of the terminal block on the EDS-510A’s
top panel. Refer to the next section for detailed instructions on how to
connect the wires to the terminal block connector, and how to attach the
terminal block connector to the terminal block receptor. In this section,
we illustrate the meaning of the two contacts used to connect the relay
contact.
FAULT:
The two sets of relay contacts of the
6
-pin terminal block connector are
used to detect user
-configured
events. The two wires attached to
the
fault contacts form an open
circuit when a user
-
configured event
is triggered. If a user
-configured
event does not occur, the
fault
circuit remains closed.
Wiring the Redundant Power Inputs
The EDS-510A has two sets of power inputs—power input 1 and power
input 2. The top two contacts and the bottom two contacts of the 6-pin
terminal block connector on the EDS-510A’s top panel are used for the
two digital inputs. The top and front views of one of the terminal block
connectors are shown here.
STEP 1: Insert the negative/positive
DC wires into the V
-/V+ terminals,
respectively.
STEP 2:
To keep the DC wires from
pulling loose, use a small flat
-
blade
screwdriver to tighten the
wire
-clamp screws on the front of
the terminal block connector.
STEP 3:
Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on
the EDS-510A’s top
panel.

- 9 -
Wiring the Digital Inputs
The EDS-510A has two sets of digital inputs, DI 1 and DI 2. Each DI
consists of two contacts of the 6-pin terminal block connector on the
EDS-510A’s top panel, which are used for the two DC inputs. The top and
front views of one of the terminal block connectors are shown here.
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴
/I1 terminals, respectively.
STEP 2:
To keep the DI wires from
pulling loose, use a small flat
-
blade
screwdriver to tighten the
wire
-clamp screws on the front of
the terminal block connector.
STEP 3:
Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on
the EDS-510A’s top
panel.
Communication Connections
Each EDS-510A switch has 3 types of communication port:
•1 RJ45 console port (RS-232 interface)
•7 10/100BaseTX Ethernet ports
•3 gigabit Ethernet ports:
3 10/100/1000BaseTX ports, or 1 10/100/1000BaseTX and 2
1000BaseSFP (mini-GBIC) ports, or 3 1000BaseSFP (mini-GBIC)
ports
In this section, we present two types of diagrams—Pinout Diagrams and
Cable Wiring Diagrams—that convey information about the ports and the
cables used to connect the EDS-510A to other devices:
Pinouts—The “Pinouts” diagrams display the type of signal passing
through each of the port’s pins.
Cable Wiring—The “Cable Wiring” diagrams present standard cable
wiring schemes for cables used to connect the EDS-510A’s ports to other
devices. These diagrams display three pieces of information:
1. When building your own cable, refer to the “pin-to-pin” cable
wiring information displayed between the two vertical dashed lines
to see which pin of the connector on the left should be connected to
which pin of the connector on the right.
2. The information to the left of the left vertical dashed lines gives the
pinouts of the relevant EDS-510A port.
3. The information to the right of the right vertical dashed line gives the
pinouts of the opposing device’s port.
NOTE
1. The pin numbers for male DB9 connectors and hole
numbers for female DB9 connectors are labeled on the
connector.
2. The pin numbers for 10-
pin RJ45 connectors (and ports) are
typically not labeled on the connector (or port). Refer to the
following Pinout and Cable Wiring diagrams to see how
10-pin RJ45 pins are numbered.

- 10 -
RS-232 Connection
The EDS-510A has one RS-232 (10-pin RJ45) console port, located on the
top panel. Use either an RJ45-to-DB9 (see the cable following wiring
diagrams) to connect the EDS-510A’s console port to your PC’s COM port.
You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the EDS-510A’s console configuration
utility.
RJ45 (10-pin) Console Port Pinouts
Pin
Description
1
---
2
DSR
3
RTS
4
---
5
TxD
6
RxD
7
GND
8
CTS
9
DTR
10
---
RJ45 (10-pin) to DB9 (F) Cable Wiring
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on the EDS-510A’s front panel are
used to connect to Ethernet-enabled devices. Most users configure these
ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are
adjusted automatically depending on the type of Ethernet cable used
(straight-through or cross-over), and the type of device (NIC-type or
HUB/Switch-type) connected to the port.
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.