Moxa technologies Iks-6324 series Manual

– 1 – – 2 – – 3 –

P/N: 1802063240012

Industrial Rackmount Switch

IKS-6324 Series

Hardware Installation Guide

Third Edition, September 2013

Package Checklist

The Moxa IKS-6324 Series industrial rackmount switches are

shipped with the following items. If any of these items is missing or

damaged, please contact your customer service representative for

assistance.

•1 Moxa IKS-6324 Switch

•Hardware Installation Guide

•Moxa Product Warranty Statement

•Protective caps for unused ports

•2 rack-mount ears

Panel Layouts

1. LED Indicators (System status, Interface Module mode,

Interface Module port)

2. Push-button switch to select mode for Interface Module

3. Model Name

4. Fast Ethernet / Gigabit Ethernet Interface Modules

5. 10/100BaseT(X) port

6. 10-pin terminal block for power inputs

7. Rack Mounting Kit

8. Ground Screw

Dimensions (unit = mm)

Fast Ethernet Interface Module

Gigabit Ethernet Interface Module

Slot 1 for 2-port PM-7200 Gigabit

Ethernet combo module, or 2

- or 1-

port

-7200 fast Ethernet modules.

Rack Mounting

Use four screws to attach the switch to a standard rack.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing

and/or wiring your Moxa industrial rackmount switch.

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes dictating the

maximum

current allowable for each wire size. If the

current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Grounding Moxa’s Rackmount Switches

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection

from the ground screw to the grounding surface prior to connecting

devices.

ATTENTION

This product is intended to be mounted to a well

grounded

mounting surface, such as a metal panel.

Wiring the Power Inputs

The IKS series supports dual redundant power supplies, named

“Power Supply 1 (PWR1)” and “Power Supply 2 (PWR2)”. The

connections for PWR1 and PWR2 are located on the terminal block.

Front view of the terminal block connectors are shown here.

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

+1-714-528-6777 (toll-free: 1-888-669-2872)

Europe:

+49-89-3 70 03 99-0

Asia-Pacific:

+886-2-8919-1230

China:

+86-21-5258-9955 (toll-free: 800-820-5036)

Wiring the Redundant Power Inputs

The IKS-6324 switch has two sets of power input—power input 1

and power input 2.

STEP 1:

Insert the dual set positive/negative DC wires into PWR1

and PWR2 terminals (+ pins 1, 9, - 

pins 2, 10). Or

insert the L/N AC wires into the PWR1 terminals (L 

1, N pin 2).

STEP 2:

To keep the DC or AC wires from pulling loose, use a

screwdriver to tighten the wire-

clamp screws on the front

of the terminal block connector.

LED Indicators

The front panel of the IKS

-6324 switch

contains several LED indicators. The

function of each LED is described in the

table below.

LED

Color

State

Description

System LEDs

STAT

GREEN

System has passed self-diagnosis

test on boot-up and is ready to

run.

Blinking System is undergoing the

self-diagnosis test.

RED On

System failed self-diagnosis on

boot-up.

PWR1 AMBER

Power is being supplied to the

main module’s power input PWR1.

Off

Power is not being supplied to the

main module’s power input PWR1.

PWR2 AMBER

Power is being supplied to the

main module’s power input PWR2.

Off

Power is not being supplied to the

main module’s power input PWR2.

FAULT RED

System initiation has failed.

Off

System initiation was successful.

NOTE: Use the Mode push-button switch to cycle among the

LNK/ACT, SPEED, and FDX/HDX LEDs. The status of these three

settings is indicated by the LEDs for the various ports. The system

will switch to LNK/ACT automatically after 5 seconds.

LED

Color

State

Description

Mode LEDs

LNK/ACT GREEN