Moxa Technologies ICS-G7828A-T Series User manual

P/N: 1802075261013
*1802075261013*
ICS-G7526A/G7528A/
G7826A/G7828A-T Series
Quick Installation Guide
Version 1.1, January 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
The Moxa ICS-G7526A/G7528A/G7826A/G7828A Series industrial
rackmount switches are shipped with the following items. If any of these
items are missing or damaged, please contact your customer service
representative for assistance.
•ICS-G7526A/G7528A/G7826A/G7828A switch
•USB cable (Type A male to Type B male)
•Power cord
•4 protective caps for unused ports
•2 rackmount ears
•Quick installation guide (printed)
•Warranty card
Panel Layouts
ICS-G7526A/G7826A
ICS-G7528A/G7828A

- 3 -
1. Model Name
2. System status LEDs
3. 10/100/1000 BaseT(X) port status LEDs
4. 100/1000 Base SFP port status LEDs
5. 10/100/1000 BaseT(X) port
6. 100/1000 Base SFP slot
7. 10/100/1000 BaseT(X) or 100/1000 Base SFP slot combo ports
8. 10 Gigabit Ethernet SFP+ slot
9. 10 Gigabit Ethernet SFP+ port status LEDs
10. Reset button
11. USB serial console port
12. USB storage port (ABC-02-USB)
13. Terminal block for Relay Output, Digital Input
14. AC power sockets for power inputs
15. Grounding screw
Dimensions
Grounding the Industrial Rackmount Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
Connecting the Power Inputs
The ICS-G7526A/G7528A/G7826A/G7828A switches support dual
redundant power supplies: Power Supply 1 (PWR1) and Power Supply 2
(PWR2). The connections for PWR1 and PWR2 are located on the rear side
(shown below). Be sure to use a standard power cord with an IEC C13
connector, which is compatible with the AC power inlet.

- 4 -
Wiring the Relay Contact
Each ICS-G7526A/G7528A/G7826A/G7828A switch has one relay output.
FAULT:
The relay contact of the 4-pin terminal block connector is used to detect
user-configured events. The two wires attached to the fault contacts form
an open circuit when a user-configured event is triggered. If a
user-configured event does not occur, the fault circuit remains closed.
USB Console Connection
The ICS-G7526A/G7528A/G7826A/G7828A series has one USB console
port (type B connector), located on the top panel. Use the USB cable
(provided in the product package) to connect the
ICS-G7526A/G7528A/G7826A/G7828A's console port to your PC's USB
port and install the USB driver (available from Moxa’s website) on the PC.
You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the
ICS-G7526A/G7528A/G7826A/G7828A’s console configuration utility.
USB Console Port (Type B Connector) Pinouts
Pin
Description
1
D– (Data -)
2
VCC (+5V)
3
D+ (Data+)
4
GND (Ground)
USB Storage Connection
The ICS-G7526A/G7528A/G7826A/G7828A series has one USB storage
port (type A connector) on the front panel. Use Moxa ABC-02-USB
automatic backup configurator to connect the
ICS-G7526A/G7528A/G7826A/G7828A's USB storage port for
configuration backup, firmware upgrade or system log file backup.
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)
NOTE
DO NOT pull out USB Automatic Backup Configurator
ABC-02-USB while writing or reading data.
The Reset Button
Depress the Reset button for five continuous seconds to load the factory
default settings. Use a pointed object, such as a straightened paper clip or
toothpick, to depress the Reset button. When you do so, the STATE LED
will start to blink about once per second. Continue to depress the STATE

- 5 -
LED until it begins blinking more rapidly; this indicates that the button has
been depressed for five seconds and you can release the Reset button to
load factory default settings.
NOTE
DO NOT power off the switch when loading default settings.
LED Indicators
The front panel of the ICS-G7526A/G7528A/G7826A/G7828A switches
contain several LED indicators. The function of each LED is described in
the table below.
LED
Color
State
Description
System LEDs
STATE
GREEN
On
The system passed the self-diagnosis test
on boot-up and is ready to run.
Blinking
1. System is undergoing the self-diagnosis
test
2. Blinks continuously when pressing the
reset button 5 seconds to reset to factory
default
3. Blinks slowly when an ABC-02
automatic backup device is detected
RED On
The system failed self-diagnosis on
boot-up.
PWR1 AMBER
On
Power is being supplied to the main
module’s power input PWR1.
Off Power is not being supplied to the main
module’s power input PWR1.
PWR2 AMBER
On
Power is being supplied to the main
module’s power input PWR2.
Off
Power is not being supplied to the main
module’s power input PWR2.
FAULT RED On The system has failed, or is under quick
inspection.
Off
The system is operating normally.
MSTR/
HEAD GREEN
On
The switch is set as the Master of the
Turbo Ring, or as the Head of the Turbo
Chain.
Blinking
The switch has become the Ring Master of
the Turbo Ring, or the Head of the Turbo
Chain, after the Turbo Ring or the Turbo
Chain is down.
Off
The switch is not the Master of this Turbo
Ring or is set as a Member of the Turbo
Chain
CPLR/
TAIL GREEN
On
The switch’s coupling function is enabled
to form a back-
up path, or when it’s set as
the Tail of the Turbo Chain.
Blinking
Turbo Chain is down
Off
The switch disables the coupling function.
When the system is importing/exporting data from or to an ABC-02
automatic backup device, the FAULT, MSTR/HEAD, and CPLR/TAIL LEDs
will blink in sequence.

- 6 -
LED
Color
State
Description
Port Status LEDs
10/100/
1000M
(TP ports)
GREEN
On
The corresponding port’s link is active.
Blinking
Data is being transmitted.
Off
The corresponding port’s link is inactive.
100/1000M
(Fiber Optic
ports)
GREEN
On
The corresponding port's link is active at
1000 Mbps.
Blinking
Data is being transmitted at 1000 Mbps.
Off
The corresponding port’s link is inactive.
AMBER
On
The corresponding port's link is active at
100 Mbps.
Blinking
Data is being transmitted at 100 Mbps.
Off
The corresponding port’s link is inactive.
10GbE
(Fiber Optic
ports)
GREEN
On
The corresponding port’s link is active.
Blinking
Data is being transmitted.
Off
The corresponding port’s link is inactive.
Specifications
Technology
Standards
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X) and 100BaseFX
IEEE 802.3ab for 1000BaseT(X)
IEEE 802.3z for 1000BaseSX/LX/LHX/ZX
IEEE 802.3ae for 10 Gigabit Ethernet
IEEE 802.3x for Flow Control
IEEE 802.1D-2004 for Spanning Tree Protocol
IEEE 802.1w for Rapid Spanning Tree Protocol
IEEE 802.1s for Multiple Spanning Tree Protocol
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.1X for Authentication
IEEE 802.3ad for Port Trunk with LACP
Protocols
IGMPv1/v2, GMRP, GVRP, SNMPv1/v2c/v3, DHCP
Server/Client, BootP, TFTP, SNTP, SMTP, RARP,
RMON, HTTP, HTTPS, Telnet, Syslog, DHCP Option
66/67/82, SSH, LLDP, IEEE 1588 PTP V2,
EtherNet/IP, Modbus/TCP, PROFINET,
SNMP Inform,
NTP Server/Client, IPv6 (ICS-G7500A series)
Layer 3 Switching
(ICS-G7800A)
Static routing, RIP V1/V2, OSPF, DVMRP, PIM-DM,
PIM-SM, PIM-SSM
Layer 3 Switching
Redundancy
(ICS-G7800A)
VRRP
MIB
MIB-II, Ethernet-like MIB, P-BRIDGE MIB, Q-BRIDGE
MIB, Bridge MIB, RSTP MIB, RMON MIB Groups 1, 2,
3, 9
Flow Control
IEEE 802.3x flow control, back pressure flow control
Interface
Gigabit Ethernet
10/100/1000BaseT(X) or 100/1000BaseSFP slot
10 Gigabit Ethernet
10GbE SFP+ slot
Console Port
USB-serial console (Type B connector)
Storage Port
USB storage (Type A connector for ABC-02-USB)

- 7 -
LED Indicators
STATE, PWR1, PWR2, FAULT, MSTR/HEAD,
CPLR/TAIL
Alarm Contact
1 relay output with current carrying capacity of
2 A @ 30 VDC
Digital Inputs 1 input with the same ground, but electrically
isolated from the electronics.
• +13 to +30V for state “1”
• -30 to +1V for state “0”
• Max. input current: 8 mA
Power Requirements
Input Voltage
110/220 VAC (85 to 264 VAC)
Input Current
Max. 1.1/0.7 A @ 110/220 VAC
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Physical Characteristics
Housing
IP30 protection
Dimensions
440 x 44 x 386.9 mm (17.32 x 1.73 x 15.23 in)
Installation
19” rack mounting
Environmental Limits
Operating Temp.
-40 to 75°C (-40 to 167°F)
Storage Temp.
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity.
5 to 95% (non-condensing)
Standards and Certifications
Safety
UL 61010-2-201, EN 61010-2-201
EMI
FCC Part 15 Subpart B Class A, EN 55032 Class A
EMS EN 61000-4-2 (ESD) Level 3
EN 61000-4-3 (RS) Level 3
EN 61000-4-4 (EFT) Level 3
EN 61000-4-5 (Surge) Level 3
EN 61000-4-6 (CS) Level 3
EN 61000-4-8
EN 61000-4-11
Rail Traffic
EN 50121-4
Shock
IEC 60068-2-27
Freefall
IEC 60068-2-32
Vibration
IEC 60068-2-6
Warranty
Warranty Period
5 years
Details
See www.moxa.com/warranty
Rack Mounting Instructions
1. Elevated Operating Ambient:If installed in a closed or multi-unit
rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
2. Reduced Air Flow:Installation of the equipment in a rack should be
such that the amount of air flow required for safe operation of the
equipment is not compromised.

- 8 -
3. Mechanical Loading:Mounting of the equipment in the rack should
be such that a hazardous condition is not achieved due to uneven
mechanical loading.
4. Circuit Overloading:Consideration should be given to the
connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
5. Reliable Earthing:Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit (e.g.
use of power strips).
Restricted Access Locations
•This equipment is intended to be used in Restricted
Access Locations, such as a computer room, with
access
limited to SERVICE PERSONAL
or USERS who have been
instructed on how to handle the metal chassis of
equipment that is so hot that special protection may be needed
before touching it. The location should only be accessible with a
key
or through a security identity system.
•External metal parts of this equipment are extremely hot!! Before
touching the equipment, you must take special precautions to protect
your hands and body from serious injury.
ATTENTION
1.
This device is only for indoor use and Pollution degree 2.
2.
Conductors rated to withstand at least 105
°C must be used
for the Power Supply Terminal.
3.
When wiring the relay contact, digital input and power inputs
,
we suggest using the cable type - AWG (American Wire
Gauge) 16-24 and the corresponding pin type cable
terminals. The connector must be able to withstand torque at
maximum 5 pound-inches.
4.
The equipment has a separate protective earthing terminal
on the chassis
that must be permanently connected to earth
ground to adequately ground the chassis and protect the
operator from electrical hazards. To avoid risks of electric
shock, do not replace or remove the protective conductor.
5.
The IP rating is not part of the safety certification.
6.
This device must be installed within a suitable enclosure.
7.
The cable that is connected to the field wiring terminals must
be able to withstand at least 75°C.
Responsible Risk
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired. The
manufacture is not responsible for any accident caused by the scenario
mentioned above.