Moxa Technologies EDS-G512E-8PoE Manual

2015 Moxa Inc. All rights reserved.
P/N: 1802005120011
*1802005120011*
EDS-G512E-8PoE Series
Hardware Installation Guide
Moxa EtherDevice™ Switch
Second Edition, July 2015
www.ipc2u.ru
www.moxa.pro

- 2 -
Package Checklist
The EDS-G512E-8PoE is shipped with the following items. If any of these
items are missing or damaged, please contact your customer service
representative for assistance.
•1 EDS-G512E-8PoE-4GSFP or EDS-G512E-8PoE-4GSFP-T Ethernet
switch
•Hardware installation guide
•Documentation and software CD
•Moxa product warranty statement
•USB cable
•Protective caps for unused ports
Features
•Up to 8 10/100/1000BaseT(X) ports and 4 100/1000BaseSFP ports
•Up to 8 IEEE 802.3af and IEEE 802.3at PoE+ standard ports
36-watt output per PoE+ port in high-power mode
Intelligent PoE power management functions
•Operate with 240 watts full PoE+ loading at -40 to 75°C
•Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250
switches), RSTP/STP, and MSTP for network redundancy
•TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance
network security
•Easy network management by web browser, CLI, USB serial console,
ABC-02-USB, MXview, MXconfig, and Windows utility
www.ipc2u.ru
www.moxa.pro

- 3 -
Panel Views of EDS-G512E-8PoE Series
Front Panel
Top Panel
Rear Panel
Front Panel
1.
1000BaseT(X) LED indicator
2.
10/100BaseT(X) LED indicator
3.
10/100/1000BaseT(X) ports
Port 1 to 8
4.
System status LED:
•STATE LED indicator
•PWR1 LED indicator
•PWR2 LED indicator
•FAULT LED indicator
•MSTR/HEAD LED indicator
•CPLR/TAIL LED indicator
5.
USB storage port
6.
SFP port LED indicator
Port 9 to 12
7.
100/1000BaseSFP slots
8.
Model Name
9.
SmartPoE LED indicator of PoE+
ports
Top Panel
1.
Reset button
2.
USB console port
3.
DIP switches for Turbo Ring,
Ring Master, and Ring Coupler
4.
Grounding screw
5.
4-pin terminal block for digital
input and power input 2
6.
4-pin terminal block for relay
output and power input 1
Rear Panel
1.
Screw holes for wall mounting
kit
2.
DIN-rail mounting kit
www.ipc2u.ru
www.moxa.pro

- 4 -
Mounting Dimensions
Unit = mm (inch)
www.ipc2u.ru
www.moxa.pro

- 5 -
DIN-Rail Mounting
The metal DIN-rail kit is fixed to the back panel of the EDS-G512E-8PoE
series when you take it out of the box. Mount the EDS-G512E-8PoE series
on corrosion-free mounting rails that meet the EN 60715 standard.
Installation
STEP 1—Insert the upper lip
of the DIN r
ail into the DIN-r
ail
mounting kit.
STEP 2
—Press the
EDS
-G512E-8PoE series
towards the
DIN rail until it
snaps into place.
Removal
STEP 1
—Pull down the latch
on the mounting kit
with a
screwdriver.
STEP 2
& 3—Slightly pull
the
EDS
-G512E-8PoE series
forward and lift up to remove
it from the DIN r
ail.
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa EDS-
G500E series on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN r
ail
attachment plate from the
rear panel
of the
EDS
-G512E-8PoE series,
and
then attach the wall
mount plates
with M3
screws
, as shown in the
figure at the right.
www.ipc2u.ru
www.moxa.pro

- 6 -
STEP 2—Mounting the EDS-G512E-8PoE series on
the wall requires 4 screws. Use the
EDS
-G512E-8PoE series, with wall mount plates
attached, as a guide to mark the correct locations
of the 4 screws. The heads of the screws should be
less than 6.0 mm in diameter, and the shafts
should be less than 3.5
mm in diameter, as shown
in the figure on at right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3—Once the screws are
fixed
to
the wall, insert the four
screw heads through the wide
parts of the keyhole
-shaped
apertures, and then slide
the
EDS
-G512E-8PoE downwards,
as indicated
in the figure at
the
right. Tighten the four screws for
more
stability.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non
-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
S
afety Extra-Low V
oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact
with the
S
afety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
ATTENTION
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit
must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).
www.ipc2u.ru
www.moxa.pro

- 7 -
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together
•You should separate input wiring from output wiring
•We advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-G512E-8PoE Series
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-G512E-8PoE series has one set of relay output. This relay
contact uses two contacts of the terminal block on the EDS-G512E-8PoE’s
top panel. Refer to the next section for detailed instructions on how to
connect the wires to the terminal block connector, and how to attach the
terminal block connector to the terminal block receptor. In this section,
we illustrate the meaning of the two contacts used to connect the relay
contact.
FAULT:
The two contacts of the 6
-pin terminal
block connector are used to detect
user
-configured events. The two wires
attached to the
fault contacts form an
open circuit when a user
-configured
event is triggered. If a user
-configured
event does not occur, the
fault circuit
remains closed.
www.ipc2u.ru
www.moxa.pro

- 8 -
Wiring the Redundant Power Inputs
The EDS-G512E-8PoE series has two sets of power inputs—power input 1
and power input 2. The top and front views of one of the terminal block
connectors are shown here.
STEP 1: Insert the negative/positive DC
wires into the V
-/V+ terminals,
respectively.
STEP 2:
To keep the DC wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-clamp
screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on
the
EDS-G512E-8PoE’s top panel.
Wiring the Digital Inputs
The EDS-G512E-8PoE series has one set of digital input (DI). The DI
consists of two contacts of the 4-pin terminal block connector on the
EDS-G512E-8PoE's top panel, which are used for the two DC inputs. The
top and front views of one of the terminal block connectors are shown
here.
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴
/I terminals, respectively.
STEP 2:
To keep the DI wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-clamp
screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which i
s located on the
EDS-G512E-8PoE’s top panel.
Communication Connections
Each EDS-G512E-8PoE series switch has 4 types of communication ports:
•1 USB console port (type B connector)
•1 USB storage port (type A connector)
•8 10/100/1000BaseT(X) Ethernet ports
•4 100/1000Base SFP slots
USB Console Connection
The EDS-G512E-8PoE series has one USB console port (type B connector),
located on the top panel. Use the USB cable (provided in the product
package) to connect the EDS-G512E-8PoE's console port to your PC's
USB port and install the USB driver (available in the software CD) on the
PC. You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the EDS-G512E-8PoE’s console
configuration utility.
www.ipc2u.ru
www.moxa.pro

- 9 -
USB Console Port (Type B Connector) Pinouts
Pin
Description
1
D– (Data -)
2
VCC (+5V)
3
D+ (Data+)
4
GND (Ground)
USB Storage Connection
The EDS-G512E-8PoE series has one USB storage port (type A connector)
on the front panel. Use Moxa ABC-02-USB-T automatic backup
configurator to connect the EDS-G512E-8PoE's USB storage port for
configuration backup, firmware upgrade or system log file backup.
ABC-02-USB Installation
Plug the ABC-02-USB into the
USB
storage port of
the Moxa
EDS
-G512E-8PoE series.
Securing the ABC
-02-USB on
the wall with an M4 screw is
suggested.
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)
1000BaseT Ethernet Port Connection
1000BaseT data is transmitted on differential TRD+/- signal pairs over
copper wires.
MDI/MDI-X Port Pinouts
Pin
Signal
1
TRD(0)+
2
TRD(0)-
3
TRD(1)+
4
TRD(2)+
5
TRD(2)-
6
TRD(1)-
7
TRD(3)+
8
TRD(3)-
www.ipc2u.ru
www.moxa.pro

- 10 -
100/1000BaseSFP (mini-GBIC) Fiber Port
The Gigabit Ethernet ports on the EDS-G512E-8PoE series are
100/1000BaseSFP Fiber ports, which require using the 100M or 1G
mini-GBIC fiber transceivers to work properly. Moxa provides completed
transceiver models for different distance requirement.
The concept behind the LC port and cable is quite straightforward.
Suppose that you are connecting devices I and II; contrary to electrical
signals, optical signals do not require a circuit in order to transmit data.
Consequently, one of the optical lines is used to transmit data from device
I to device II, and the other optical line is used transmit data from device
II to device I, for full-duplex transmission.
Remember to connect the Tx (transmit) port of device I to the Rx (receive)
port of device II, and the Rx (receive) port of device I to the Tx (transmit)
port of device II. If you make your own cable, we suggest labeling the two
sides of the same line with the same letter (A-to-A and B-to-B, as shown
below, or A1-to-A2 and B1-to-B2).
LC-Port Pinouts
LC-Port to LC-Port Cable Wiring
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.
Reset Button
There are two functions available on the Reset Button. One is to reset the
Ethernet switch to factory default settings by pressing and holding the
Reset button for 5 seconds. Use a pointed object, such as a straightened
paper clip or toothpick, to depress the Reset button. This will cause the
STATE LED to blink once a second. After depressing the button for 5
continuous seconds, the STATE LED will start to blink rapidly. This
indicates that factory default settings have been loaded and you can
release the reset button.
When the ABC-02-USB is connected to the EDS-G512E-8PoE Ethernet
switch, the reset button allows quick configuration and backs up log files
to the ABC-02-USB. Press the Reset button on top of the
EDS-G512E-8PoE, the Ethernet switch will start backing up current
system configuration files and event logs to the ABC-02-USB.
NOTE
Do NOT power off the Ethernet switch when loading default
settings.
www.ipc2u.ru
www.moxa.pro