Moxa Technologies EtherDevice EDS-G500E Series User manual

2013 Moxa Inc. All rights reserved.
P/N: 1802005000020
EDS-G500E Series
Hardware Installation Guide
Moxa EtherDevice™ Switch
First Edition, July 2013

- 2 -
Package Checklist
The EDS-G500E is shipped with the following items. If any of these items
are missing or damaged, please contact your customer service
representative for assistance.
•1 EDS-G508E or EDS-G512E-4GSFP or EDS-G516E-4GSFP Ethernet
switch
•Hardware installation guide
•Documentation and software CD
•Moxa product warranty statement
•USB cable
•Protective caps for unused ports
Features
•Up to 12 10/100/1000BaseT(X) ports and 4 100/1000BaseSFP ports
•Turbo Ring and Turbo Chain (recovery time < 50 ms @ 250 switches),
RSTP/STP, and MSTP for network redundancy
•RADIUS, TACACS+, SNMPv3, IEEE 802.1x, HTTPS, and SSH to
enhance network security
•EtherNet/IP, PROFINET, and Modbus/TCP protocols supported for
device management and monitoring

- 3 -
Panel Views of EDS-G500E Series
Front Panel
EDS-G508E
EDS-G512E-4GSFP
Front Panel
1.
1000BaseT(X) LED indicator
2.
10/100BaseT(X) LED indicator
3.
10/100/1000BaseT(X) ports
EDS-G508E: 1 to 8
EDS-G512E-4GSFP: 1 to 8
EDS-G516E-4GSFP: 1 to 12
4.
System status LED:
•STATE LED indicator
•PWR1 LED indicator
•PWR2 LED indicator
•FAULT LED indicator
•MSTR/HEAD LED indicator
•CPLR/TAIL LED indicator
5.
USB storage port
6.
SFP port LED indicator
EDS-G512E-4GSFP: 9 to 12
EDS-G516E-4GSFP: 13 to 16
7.
100/1000BaseSFP slots
8.
Model Name
EDS-G516E-4GSFP

- 4 -
Top Panel
Rear Panel
Top Panel
1.
Reset button
2.
USB console port
3.
DIP switches for Turbo Ring,
Ring Master, and Ring Coupler
4.
Grounding screw
5.
4-pin terminal block for digital
input and power input 2
6.
4-pin terminal block for relay
output and power input 1
Rear Panel
1.
Screw holes for wall mounting
kit
2.
DIN-rail mounting kit

- 5 -
Mounting Dimensions
Unit = mm (inch)

- 6 -
DIN-Rail Mounting
The metal DIN-rail kit is fixed to the back panel of the EDS-G500E series
when you take it out of the box. Mount the EDS-G500E series on
corrosion-free mounting rails that meet the EN 60715 standard.
Installation
STEP 1—Insert the upper lip of the DIN rail into the DIN-rail mounting kit.
STEP 2—Press the EDS-G500E series towards the DIN rail until it snaps
into place.
Removal
STEP 1—Pull down the latch on the mounting kit with a screwdriver.
STEP 2 & 3—Slightly pull the EDS-G500E series forward and lift up to
remove it from the DIN rail.

- 7 -
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa EDS-
G500E series on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN rail attachment
plate from the rear panel
of
the EDS
-G500E series, and
then attach the wall mount
plates
with M3 screws, as
shown
in the figure at the
right.
STEP 2—
Mounting the EDS-G500E series on the
wall requires 4 screws. Use the
EDS-G500E series
,
with wall mount plates attached, as a guide to
mark the correct locations of the 4 screws. The
heads of the screws should be less than 6.0 mm
in
diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure on at right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3—Once the screws are
fixed
to the wall, insert the
four screw heads through the
wide parts of the
keyhole
-shaped apertures,
and then slide
the EDS-
G500E
downwards, as indicated
in
the figure
at
the right. Tighten
the four screws for
more
stability.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non
-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed
for operation with a
S
afety Extra-Low V
oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
S
afety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.

- 8 -
ATTENTION
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum
current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together
•You should separate input wiring from output wiring
•We advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-G500E Series
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-G500E series has one set of relay output. This relay contact uses
two contacts of the terminal block on the EDS-G500E’s top panel. Refer to
the next section for detailed instructions on how to connect the wires to
the terminal block connector, and how to attach the terminal block
connector to the terminal block receptor. In this section, we illustrate the
meaning of the two contacts used to connect the relay contact.

- 9 -
FAULT:
The two contacts of the 6
-
pin terminal
block connector are used to detect
user
-
configured events. The two wires
attached to the
f
ault contacts form an
open circuit when a user
-configured
event is triggered. If a user
-
configured
event does not occur, the
fault circuit
remains closed.
Wiring the Redundant Power Inputs
The EDS-G500E series has two sets of power inputs—power input 1 and
power input 2. The top and front views of one of the terminal block
connectors are shown here.
STEP 1: Insert the negative/positive
DC wires into the V
-/V+ terminals,
respectively.
STEP 2:
To keep the DC wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-
clamp
screws on the front of the terminal
block connector.
STEP 3:
Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-G500E’s top panel.
Wiring the Digital Inputs
The EDS-G500E series has one set of digital input (DI). The DI consists of
two contacts of the 4-pin terminal block connector on the EDS-G500E's
top panel, which are used for the two DC inputs. The top and front views
of one of the terminal block connectors are shown here.
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴
/I terminals, respectively.
STEP 2:
To keep the DI wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-
clamp
screws on the front of the terminal
block connector.
STEP 3:
Insert the plastic terminal
block connector prongs into the
terminal block receptor,
which is
located on the EDS-G500E’s top panel.
Communication Connections
Each EDS-G500E series switch has 4 types of communication ports:
•1 USB console port (type B connector)
•1 USB storage port (type A connector)
•8 (EDS-G508E/EDS-G512E-4GSFP) or 12 (EDS-G516E-4GSFP)
10/100/1000BaseT(X) Ethernet ports
•4 100/1000Base SFP slots (EDS-G512E-4GSFP/EDS-G516E-4GSFP)

- 10 -
USB Console Connection
The EDS-G500E series has one USB console port (type B connector),
located on the top panel. Use the USB cable (provided in the product
package) to connect the EDS-G500E's console port to your PC's USB port
and install the USB driver (available in the software CD) on the PC. You
may then use a console terminal program, such as Moxa PComm Terminal
Emulator, to access the EDS-G500E’s console configuration utility.
USB Console Port (Type B Connector) Pinouts
Pin
Description
1
D– (Data -)
2
VCC (+5V)
3
D+ (Data+)
4
GND (Ground)
USB Storage Connection
The EDS-G500E series has one USB storage port (type A connector) on
the front panel. Use Moxa ABC-02-USB-T automatic backup configurator
to connect the EDS-G500E's USB storage port for configuration backup,
firmware upgrade or system log file backup.
ABC-02-USB Installation
Plug the ABC-02-USB into the USB storage port of the Moxa EDS-G500E
series. Securing the ABC-02-USB on the wall with an M4 screw is
suggested.
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)