Moxa Technologies IKS-G6524 Manual

– 1 – – 2 – – 3 –
P/N: 1802068240010
IKS-G6524/G6824 Series
Hardware Installation Guide
First Edition, May 2011
Package Checklist
The Moxa IKS-G6524/G6824 Series industrial rackmount switches
are shipped with the following items. If any of these items are
missing or damaged, please contact your customer service
representative for assistance.
•IKS-G6524/G6824 switch
•RJ45 to DB9 console port cable
•2 power cords
•Protective caps for unused ports
•2 rackmount ears
•Documentation and software CD
•Hardware installation guide (printed)
•Warranty card
Panel Layouts
1. Model Name
2. System status LEDs
3. 10/100/1000 BaseT(X) port status LEDs
4. 100/1000Base SFP port status LEDs
5. 10/100/1000 BaseT(X) port
6. 100/1000Base SFP slot
7. 10/100/1000 BaseT(X) or 100/1000Base SFP slot combo ports
8. Serial Console port
9. Terminal block for Relay Output, Digital Input
10. AC power sockets for power inputs
11. Grounding screw
Dimensions (unit = mm)
Grounding the Moxa Industrial Rackmount
Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection
from the ground screw to the grounding surface prior to connecting
devices.
Connecting the Power Inputs
The IKS-G6524/G6824 series of switches supports dual redundant
power supplies: Power Supply 1 (PWR1) and Power Supply 2
(PWR2). The connections for PWR1 and PWR2 are located on the
rear side (shown below). Be sure to use a standard power cord
with an IEC C13 connector, which is compatible with the AC power
inlet.
LED Indicators
The front panel of the IKS-G6524/G6824 Series switch contains
several LED indicators. The function of each LED is described in the
table below.
LED Color State Description
System LEDs
STAT GREEN On System has passed
self-diagnosis test on
boot-up and is ready to run.
Blinking System is undergoing the
self-diagnosis test.
RED On System failed self-diagnosis
on boot-up.
PWR1 AMBER On Power is being supplied to
the main module’s power
input PWR1.
Off Power is not being supplied
to the main module’s power
input PWR1.
PWR2 AMBER On Power is being supplied to
the main module’s power
input PWR2.
Off Power is not being supplied
to the main module’s power
input PWR2.
FAULT RED On System is in the event of
failure, or is under quick
inspection.
Off System is in normal
operation.
MSTR/
HEAD
GREEN On When the IKS-G6524/G6824
is set as the Master of the
Turbo Ring, or as the Head of
the Turbo Chain.
Blinking The IKS-G6524/G6824 has
become the Ring Master of
the Turbo Ring, or the Head
of the Turbo Chain, after the
Turbo Ring or the Turbo
Chain is down.
Off The IKS-G6524/G6824
is not
the Master of this Turbo Ring
or is set as a Member of the
Turbo Chain
CPLR/
TAIL
GREEN On When the IKS-G6524/G6824
coupling function is enabled
to form a back-up path, or
when it’s set as the Tail of
the Turbo Chain.
Blinking When the Turbo Chain is
down
Off When this
IKS-G6524/G6824 switch
disables the coupling
function.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific: [phone]
China:
[phone] (toll-free: 800-820-5036)
2011 Moxa Inc., All Rights Reserved
LED Color State Description
Port Status LEDs
10/100/
1000M (TP
ports)
GREEN On The corresponding port’s
link is active.
Blinking The corresponding port’s
data is being transmitted.
Off The corresponding port’s
link is inactive.
100/1000M
(Fiber Optic
ports)
GREEN On Fiber optic port's 1000
Mbps link is active.
Blinking
Data is being transmitted at
1000 Mbps.
Off Fiber Optic port’s 1000
Mbps link is inactive.
AMBER On Fiber optic port's 100 Mbps
link is active.
Blinking
Data is being transmitted at
100 Mbps.
Off
Fiber Optic port’s 100 Mbps
link is inactive.
Specifications
Technology
Standards IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X) and 100BaseFX
IEEE 802.3ab for 1000BaseT(X)
IEEE 802.3z for 1000BaseSX/LX/LHX/ZX
IEEE 802.3x for Flow Control
IEEE 802.1D for Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.1X for Authentication
IEEE 802.3ad for Port Trunk with LACP
Protocols IGMPv1/v2 device, GMRP, GVRP,
SNMPv1/v2c/v3, DHCP Server/Client, DHCP
Option 82, BootP, TFTP, SNTP, SMTP, RARP,
RMON, HTTP, HTTPS, Telnet, SSH, Syslog
Layer 3
Switching
Static routing, RIP V1/V2, OSPF, VRRP for
router redundancy (IKS-G6824 only)
MIB MIB-II, Ethernet-like MIB, P-BRIDGE MIB,
Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON
MIB Groups 1, 2, 3, 9
Flow Control IEEE 802.3x flow control, back pressure flow
control
Interface
Gigabit Ethernet
10/100/1000BaseT(X) or 100/1000BaseSFP slot
Console Port RS-232 (RJ45 connector)
LED Indicators STAT, PWR1, PWR2, FAULT, MSTR/HEAD,
CPLR/TAIL
Alarm Contact
1 relay output with current carrying capacity of 2
A @ 30 VDC
Digital Inputs 1 input with the same ground, but electrically
isolated from the electronics.
• +13 to +30V for state “1”
• -30 to +3V for state “0”
• Max.input current: 8 mA
Power Requirements
Input Voltage 110/220 VAC (85 to 264 VAC)
Input Current Max. 0.79/0.44 A @ 110/220 VAC
Overload Current
Protection
Present
Reverse Polarity
Protection
Present
Physical Characteristics
Housing IP 30 protection
Dimensions 440 x 44 x 386.9 mm (17.32 x 1.73 x 15.23 in)
Installation 19”rack mounting
Environmental Limits
Operating Temp. Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity.
5 to 95% (non-condensing)
Standards and Certifications
Safety UL 60950-1 (Pending), EN 60950-1 (Pending)
EMI FCC Part 15 Subpart B Class A, EN 55022 Class A
Rail Traffic EN50121-4
Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty
Rack Mounting Instructions
1. Elevated Operating Ambient:If installed in a closed or
multi-unit rack assembly, the operating ambient temperature
of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the
equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
2. Reduced Air Flow:Installation of the equipment in a rack
should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
3. Mechanical Loading:Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
4. Circuit Overloading:Consideration should be given to the
connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used
when addressing this concern.
5. Reliable Earthing:Reliable earthing of rack-mounted
equipment should be maintained. Particular attention should
be given to supply connections other than direct connections
to the branch circuit (e.g. use of power strips)."
Restricted Access Locations
•This equipment is intended to be used in Restricted Access
Locations, such as a computer room, with access limited to
SERVICE PERSONAL or USERS who have been instructed on
how to handle the metal chassis of equipment that is so hot
that special protection may be needed before touching it. The
location should only be accessible with a key or through a
security identity system.
•External metal parts of this equipment are extremely hot!!
Before touching the equipment, you must take special
precautions to protect your hands and body from serious
injury.