Moza CS V2 User manual

MOZA CS V2 Steering Wheel
Quick Guide
Hold on Tight, Experience Real Racing
User Manual 使用
说
明
书

01
Product Introduction
· 13-inch standard racing rim
· Aviation grade aluminum alloy frame
· Forged carbon fiber photoelectric magnetic paddle
· RGB sequential shift indicator
· Programmable mechanical buttons
· Customized quick release from real racing
· Wireless or wired power supply and communication technology
02
Quick Release Manual
1. Match the 6 steel ball bearings on the female quick release head of the steering wheel with the
6 grooves on the quick release male head of the base
2. Press the quick release in the direction of the wheel
3. The quick release will automatically return to position and lock up, if not, you couldtry to rotate the
wheel slightly or remove it and then reinstall it
4. If you need to remove the wheel, press the quick release with both hands, and pull out the wheel
at the same time
03
Steering Wheel Configuration
Youcan set up the CS V2 steering wheel quickly and easily in the MOZA Pit House software.
· Joystick mode: push buttons or cross keys
· Indicator switch mode: the indicator status has three modes which are matching rotating speed,
off and always on.
· Indicators display mode: mode 1 and mode 2. Detailed explanations will pop up when clicking each option.
· Rev speed prompt setting: there are four modes according to the timing relationship between the rev
speed and the shift indicator light, which are advanced, standard, extreme, and custom mode.
· Brightness adjustment: adjust the brightness of the shift indicator.
· Indicator color adjustment: drag the color block you like to the indicator to change the color.
· Shifter paddle calibration: if you are sensing abnormalities in the shifter paddle, click here to
calibrate.

(For detailed steering wheel settings and functions, please visit the official website of MOZA
Racing at www.mozaracing.com)

04
Install Heightening Block for Magnetic Paddle
Placethe steering wheel on a flat surface facing down,use a hexagonal wrench to remove thescrew on the side
of the triggerlever of the shift paddle,and then use a wrench to lift the latch from the side of the magnetic
paddle,and pull the trigger leverof the paddleoutward to obtainthe best space for disassemblingand
assemblingpaddles; use a hexagonal wrenchto removethe screwson the shift paddles,put on the heightening
block and tighten with the long screws, andfinally put the latch back in place and tighten the screws. The
heightening block can help shorten thedistance between the magnetic shifter paddles and hands by 8mm.
05
Install Silence Pad for the Magnetic Paddle
Place the steering wheel on a flat surface, with the front facing down. Use a hexagonal wrench toremove the
screwon the side of the trigger lever,then use a wrenchto lift the latchfrom the side of the magnetic paddle
(NOTE: you do not need to push it out completely.Justseparating thetrigger lever and the latch is fine).Apply
the silencer pad on the back of the magnetic hole and the squarehole on the shifterpaddle (if it is
inconvenientto operate,you can lift the latchcompletely). Do not applythe silencer pad on the square hole
because this is the photoelectrictrigger area.Finally, return the latch into place and tighten the screws.
06
Packing Details
1.CS V2 Steering Wheel
2. Tool kit: Hexagonal Wrench / 8mm aluminum heightening block x 2 / Silence pad x 4
07
Product Parameters
Grip Material: microfiber leather
Frame Material: aluminum
Face Plate Material: aluminum
Magnetic paddle Material: forged carbon fiber Size:
13 inch
Magnetic Paddle: 2 pcs Mechanical
Keys: 6
Front-Facing knobs: 2 pcs (20-segment embedded
steel ball type)
Universal Joystick: 2 pcs (pressable)
Highlighted LED RGB Light Beads: 10 pcs LED Color:
7 colors for customization Intelligent Telemetry:
yes
Adjust Lighting though MOZA Pit House: yes Quick
Release: yes
Power Supply Method: wireless and wire Signal
Transmission Method: wireless Magnetic paddle
sensor: contactless photoelectric sensor

01
产 品介 绍
·13 英寸标准竞技环身
·航空级铝合金骨架
·锻造碳纤维磁吸光电拨片
·RGB 流水式换档指示灯
·高级机械键盘式可编程按钮
·源自真实赛车的专属快拆系统
·无线或有线供电和通讯技术
02
快拆使用方法
正面 背面
1. 将方向盘快拆母头上 6 颗钢珠的位置与基座快拆公头的 6 个凹槽对应
2. 将快拆往盘面方向按压
3. 快拆将自动归位锁紧，若无归位，可尝试轻微转动盘面或取下后再安装
4. 如需拆取盘面，用双手捏住黑色快拆部分，同时并拔出盘面
03
方向 盘 配置
在 MOZA Pit House 软件中可以方便快捷地对CS V2 方向盘进行设置。
·摇杆模式：设置摇杆操作模式，可设置为按键和十字键
·指示灯开关模式：指示灯状态调节，分为随速转动，关闭和常亮
·指示灯显示模式：共分为模式一和模式二，当鼠标移动到选项上时会弹出详细解释
·转速提示设置：根据转速与换档指示灯亮起的时机关系，分为提前型，标准型，极限型和自定 义模
式
·亮度调节：调节换档指示灯的亮度
·指示灯颜色调节：将喜欢的色块拖动到指示灯上即可更换颜色
·拨片校准：当拨片感应异常时，通过点击此处进行拨片校准

（详细方向盘设置与功能，请访问 MOZA Racing 官网）

04
拨
片接近
块
的安装
将方向盘放置于平面上使盘面朝下，使用六角扳手取下换挡拨片触发杆一侧的螺丝，再用扳手 从磁吸拨片
侧顶开插销，将拨片触发杆向外拉以获得拆装拨片的最佳空间；使用六角扳手将换 挡拨片上的螺丝取下，
垫上增高块后用附带的长螺丝拧紧，最后将插销归位并装回螺丝，通过此垫片可将拨片与手的距离拉近
8mm。
05
磁吸 拨 片静音 垫 的安装
将方向盘放置于平面上使盘面朝下，使用六角扳手取下换挡拨片触发杆一侧的螺丝，再用扳手 从磁吸拨片
一侧顶开插销（无需完全顶出，仅使磁吸拨片触发杆与插销可以分离即可），然后将 静音垫贴在磁铁孔背面
与拨片座上的方孔外侧位置（如不方便操作，可以先将换挡拨片取下，然 后将换挡触发杆从拨片座上分离
出来），切勿将静音垫贴在方孔上（此处为拨片光电开关感光区 域，静音垫覆盖上去会影响拨片功能）如
图示，最后将插销归位并装回螺丝。
06
包装清 单
1.CS V2 方向盘2. 工具包：六角螺丝刀 / 8mm 铝合金接近块x2 / 静音垫x4
07
产
品参数
环身包覆材质：超纤皮 骨
架材质：铝合金面板材质：
铝合金 拨片材质：锻造碳
纤维 尺寸：13 英寸磁吸拨
片：2 个机械键盘质感按键：
6 个
正面旋钮：2 个（20 段内嵌钢珠式）
万向摇杆：2 个（可按压）高亮
LED RGB 灯珠：10 颗
LED 色彩：7 色自定义智能遥测：
支持
通过MOZA Pit House 设置灯光：支持
拆装方式：现实赛车快拆 供电方式：无线
和有线信号传输方式：无线磁吸拨片感应
方式：光电无接触式

产品保修卡
产品型号
购买日期
用户姓名
用户电话
产品条码
通讯地址
经销商信息（签章）
产
品保修条例
保修期
自购机日起，基座主体，方向盘，踏板和仪表显示屏保修 12 个月。设备外壳、说明书、线材、螺丝、扳 手、
包装等不在“一年免费保修服务“范围内，但您可以选择有偿服务。购买者在以下条件下不享受免费保
修服务：
1. 超过三包有效期的；
2. 无三包凭证及有效发票的，但能够证明该产品在三包有效期内的除外；
3. 保修凭证上的型号与维修产品型号不符或者涂改的；
4. 非本公司特约维修人员拆动造成损坏的；
5. 因不可抗力造成损坏的；
6. 未按产品使用说明书要求使用、维护、保养而造成损坏的； 保修期限鉴于产品部位、不同国家法律
法规等差异，将有所不同。相关国家与区域的保修期限，请咨询MOZA 官方或购买时联系的
MOZA 授权经销商。