-6- -7-
USING THE REPEAT FUNCTION
CD REPEAT
You can play one track or all tracks on the disc repeatedly.
To Repeat a single Track
1.Press REPEAT button once in play, CD REPEAT indicator on the display will be steady on in the display.
The current track will be played over and over again till you press STOP button.
2.To cancel repeat 1play, press REPEAT button twice , REPEAT 1 indicator goes off.
To Repeat All the Tracks
1.Press REPEAT button twice in play, REPEAT ALL indicator on the display will be steady on in the display,
all tracks on the disc will be played over and over again till you press STOP button.
2.To cancel repeat all play, press REPEAT button three times, REPEAT ALL indicator goes off.
Note: Repeat function can't be done in stop mode.
USING THE PROGRAM FUNCTION
The CD Player in this unit has a 65 tracks programmable memory which allows you
to program up to 65 tracks on any disc for playback in any desired order. To program
tracks for play back the player must be in the Stop mode. If the disc is playing, press
the stop button to stop playback and then proceed as follow.
1.In the During stop mode.
2.Press PROGRAM button once .The MEMORY Indicator begins appear
3.Press BACK or NXET for your desired track or Press number key on the remote control.
4.When your chosen track number appears, press PROGRAM once to store the track.
5.Repeat steps 1 to 4 to select and store all desired tracks in this way.
6.After end of program. press PLAY to start play the tracks in the order that you selected
MP3 REPEAT
You can play one track or all tracks on the disc repeatedly.
To Repeat a single Track
1.Press REPEAT button once in play, REPEAT indicator on the display will be steady on in the display.
The current track will be played over and over again till you press STOP button.
2.To cancel repeat 1 play, press REPEAT button three times , REPEAT 1 indicator goes off.
To Repeat All the Tracks
1.Press REPEAT button twice in play, REPEAT ALL indicator on the display will be steady on in the
display, all tracks on the disc will be played over and over again till you press STOP button.
2.To cancel repeat all play, press REPEAT button twice, REPEAT ALL indicator goes off.
To Repeat ALBUM the Tracks
1.Press REPEAT button three times, then REPEAT ALB2 is displayed. Repeat the current play album.
2.To cancel repeat album play. press REPEAT button once. REPEAT ALB2 indicator goes off.
Note: Repeat function can't be done in stop mode.
MP3 Programmed Playback
The mp3 Player in this unit has a 65 tracks programmable memory which allows you
to program up to 65 tracks on any disc for playback in any desired order. To program
tracks for play back the player must be in the Stop mode. If the disc is playing, press
the stop button to stop playback and then proceed as follow.
1.In the During stop mode.
2.Press PROGRAM button once .The ALBUM NO. is flashing
3.Press BACK or NEXT for your desired album.
4.Press MEMORY button once. track NO. is flashing
5.Press BACK or NEXT chosen track number appears or Press number key on the remote control,
press PROGRAM once to store the track.
6.Repeat steps 1 to 5 to select and store all desired tracks in this way.
7.After end of program. press PLAY to start play the tracks in the order that you selected
NOTICE : After the 65 tracks of program is full, program don't be continue.
VOL UME
MEM ORY
ESP
MEM ORY
VOL UME
RADIO /CD/MP3 OPERATION
USING THE RADIO
1.Press FUNC button. Select TUNER mode or press BAND button on CD/AUX/USB mode.
2.Press BAND to select the desired wave band: AM, FM
3.Tune to required station by press BACK/TUNE-DN or NEXT/TUNE-UP
Manual Tuning: Press BACK/TUNE-DN or NEXT/TUNE-UPand then release within 1 sec.
Auto Tuning: Hold BACK/TUNE-DN or NEXT/TUNE-UP over 1sec .And then release it at any time. After key release,
the auto-tuning operation will start until find a station.
Preset Channel:(FM 30 Preset memories,AM 10 preset memories)
(1) Press BACK/TUNE-DN or NEXT/TUNE-UP Select desired station.
(2) Press PROGRAM button once , The MEMORY number indicator begins steady in the display.
(3) Press PRESET-UP OR PRESET DOWN buttons to select the desired number
(4) Press PROGRAM button to save that station.
(5) Repeat steps (1) to (4) procedures for other stations.
4.After end of program. press PRESET-UP or PRESET-DN to start play the frequency that you selected or
Press number key on the remote control
5.Adjust VOLUME button to desired volume level
Note: The FM STEREO indicator will be on when you are receiving FM stereo programmable.
6.Turn off the radio by press FUNC button select other mode or press power button to off the unit.
7.Switch on again after shut down,the memory frequency still exists.
MONO/ STEREO
Press MO/ST button once , MONO is displayed
Press MO/ST button twice , STEREO is displayed
Notice:the mono/stereo can't be done on AM.
PLAYING CD/MP3
1.Press FUNC button select CD mode
2.Open the disc compartment door.
3.Place a CD/MP3 disc into the tray with the label side facing up.
4.Close the disc compartment door( auto play) or When other mode, it will playback automatically.
5.To interrupt playback, press PLAY/PAUSE button. The track number will be flashed every 0.5s.
Pause function will be kept after BACK or NEXT.
To resume playback, press PLAY/PAUSE button again to continue.
6.CD PLAY, LCD display shows ESP word , ESP function begin working,
ESP time is 2 seconds in the CD mode,ESP time is 5 seconds in the Mp3 mode.
NOTE:It can't cancel the ESP function under the CD/MP3 mode.
7.To stop playback, press STOP button to stop play and then total time and total number will show
on the display.
SELECTING A DESIRED TRACK/PASSAGE
During playback you can use BACK/TUNE-DN or NEXT/TUNE-UP to select a particular track.
1.If you have select a track number in the stop or pause position, press PLAY/PAUSE to start playback.
2.Press NEXT/TUNE-UP once briefly for the next track,
3.Press BACK/TUNE-DN than once briefly for a previous track.
To search for a particular passage during playback(track scanning at high speed)
Press and hold BACK/TUNE-DN or NEXT/TUNE-UP- button to scan the current playing track at high speed
until desired point(passage),then release the button. Playback will start again from this point.
To remove the CD ,press OPEN to open Compartment lid, grasp the CD by its edges. And carefully take it out.
Note:
To ensure good system performance; wait until the disc tray completely reads the disc before proceeding.
If no disc loaded into the compartment, or the disc is placed upside down or unreadable, a DISC display
will be indicted.
