MR.LONGARM 0975 User manual

0975i 9/2021
BULB CHANGERS
Mr. LongArm bulb changers and bulb
changing extension poles are non-
conductive which means they won’t
conduct electricity as long as they are
completely dry. Having said that you
should always turn off your light
switch before changing any bulb!
Also, wear safety goggles when
changing light bulbs just in case one
breaks while you are working with it.
Complete Light Bulb Changer
Kit with 3 ft - 6 ft Non-
Conductive Extension Pole
Scan for video
instructions.
#0975
Thank You!
for purchasing our
Complete Light Bulb Changer Kit
& 3 ft - 6 ft Non-Conductive
Extension Pole.
If you need assistance, please contact
our Customer Service at:
1-800-821-3508 or use the contact
forms on our website at:
https://mrlongarm.com/contact-us/
©2021 Mr. LongArm, Inc.
P.O. Box 377, Greenwood, MO 64034
Standard-
shaped
incandescent
and LED
bulbs.
Smooth-faced
floodlight
bulbs.
Spotlight
bulbs.

SMART BULB CHANGER KIT
The Smart bulb changer kit fits standard-
shaped incandescent and LED bulbs, spot-
light and floodlight bulbs. You’ll have one
handle and three different sized cups. To
change cups simply pull the lock clip at the
top of the handle out and the cup and pin will
lift off the top of the handle. Now insert the
desired cup size and replace the lock clip. Be
sure not to loose the pin as it closes the hole
in the suction cup and controls the suction
when using the bulb changer.
The small red suction cup holds most stan-
dard-shaped incandescent and LED bulbs.
The medium blue suction cup holds spotlight
bulbs and the large yellow suction cup holds
floodlight bulbs.
EXTENSION POLES
Next you’ll want to attach the bulb changer
handle to your extension pole. The non-con-
ductive extension pole will have a hole drilled
through the threaded end to accept a lock
clip which keeps it from loosening during
bulb removal. Just tighten down the bulb
changer handle by screwing it on clockwise,
making sure the hole in the bottom of the
handle aligns with the hole in the threaded
end on the pole and insert the lock clip.
If you want to use the bulb changer with
other extension poles just be sure to tighten
down the handle by screwing it on clockwise,
very firmly to avoid having it unscrew when
removing light bulbs. Mr. LongArm’s heavy
duty poles do have a lok-thread which will
keep the bulb changer handle from loosening
if it is firmly screwed down.
USING THE BULB CHANGER
Adjust your extension pole to the height
needed to comfortably reach the bulb. Now
make sure the inside of the cup is clean, we
suggest wiping it down with a damp cloth.
The moisture will also help you get a good
suction on the bulb. Also make sure the pin is
engaged so the hole in the cup is closed,
otherwise you won’t be able to get suction
on the bulb.
Align the bulb changer directly below the
bulb and lift it up to the bulb and push to
attain suction. Once you are sure you have
good suction unscrew the light bulb by turn-
ing it to the left and carefully lower the bulb.
To release the suction hold the bulb and cup
and pull down on the handle, this will disen-
gage the pin and the bulb will release.
Now you’re ready to put the new bulb in
place. Hold it in your hand and push the
bulb changer up to it to attain suction,
check to make sure its secure and raise the
bulb up to the fixture. Screw the bulb in
place by turning it to the right, don’t over-
tighten. To release the suction pull down on
the handle, this will disengage the pin and
the bulb will release.
Sometimes you may encounter a bulb that
has corroded in place or one that has been
over-tightened and you may have to remove
those bulbs by hand. But you should be able
to install the new bulb with your Mr.
LongArm bulb changer.
LOCK
CLIP™ PIN