MSA 507003 User manual
Page 4 © 2019, MSA
P/N 10040813 User Instructions MSA Tool Holder
User Instructions
MSA Tool Holder
6” Tool Holder & 18” Tool Holder
TWP 122 (L) Rev. 5 © MSA 2019 Prnt. Spec. 10000005196 (B) Mat. 10040813
Doc. 10040813
CR 800000032681
Model Numbers:
507003, 507004, 507005, 507006
1.0 PURPOSE
For safe holding of large sledge-driven tools, such as stone points, star drills, chisels, frost pins, gouges, ground rods, jack
bits, punches, and marking dies.
2.0 SET-UP
1. Loosen knob or T-handle, allowing slack in tool strap (see image 1)
2. Pull on tool strap to gain some slack in the strap (see image 2)
Image 1
Image 2
WARRANTY
Express Warranty – MSA warrants that the product furnished is free from mechanical defects or faulty
workmanship for a period of one (1) year from rst use or eighteen (18) months from date of shipment,
whichever occurs rst, provided it is maintained and used in accordance with MSA’s instructions and/
or recommendations. Replacement parts and repairs are warranted for ninety (90) days from the date
of repair of the product or sale of the replacement part, whichever occurs rst. MSA shall be released
from all obligations under this warranty in the event repairs or modications are made by persons other
than its own authorized service personnel or if the warranty claim results from misuse of the product.
No agent, employee or representative of MSA may bind MSA to any afrmation, representation or
modication of the warranty concerning the goods sold under this contract. MSA makes no warranty
concerning components or accessories not manufactured by MSA, but will pass on to the Purchaser
all warranties of manufacturers of such components. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, AND IS STRICTLY LIMITED TO THE TERMS
HEREOF. MSA SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
Exclusive Remedy – It is expressly agreed that the Purchaser’s sole and exclusive remedy for breach
of the above warranty, for any tortious conduct of MSA, or for any other cause of action, shall be the
repair and/or replacement, at MSA’s option, of any equipment or parts thereof, that after examination by
MSA are proven to be defective. Replacement equipment and/or parts will be provided at no cost to the
Purchaser, F.O.B. Purchaser’s named place of destination. Failure of MSA to successfully repair any
nonconforming product shall not cause the remedy established hereby to fail of its essential purpose.
Exclusion of Consequential Damages – Purchaser specically understands and agrees that under
no circumstances will MSA be liable to Purchaser for economic, special, incidental, or consequential
damages or losses of any kind whatsoever, including but not limited to, loss of anticipated prots and any
other loss caused by reason of the non-operation of the goods. This exclusion is applicable to claims for
breach of warranty, tortious conduct or any other cause of action against MSA.
For additional information please contact the Customer Service Department at 1-800-MSA-2222 (1-
800-672-2222).
Page 2 © 2019, MSA
P/N 10040813 User Instructions MSA Tool Holder
© 2019, MSA Page 3
User Instructions MSA Tool Holder P/N 10040813
3. Place tool (i.e. chisel) into tool holder so that tool is inside strap and resting on pads (see image 3)
4. While holding tool in place, tighten strap by twisting T-handle in clockwise direction (see image 4) until tool is
securely in place.
! WARNING
User must wear eye protection while using this product. Debris created by striking
objects can result in eye or other bodily injury.
Image 3 Image 4
3.0 USE
Grasp Tool Holder, keeping your hand away from striking tool. Place striking tool against desired surface. Strike
tool (see image 5)
DO NOT strike tool in the direction that pulls directly against the straps (see image
6). Tool Holder is not intended to be used as a prying tool or with a hammer wrench.
Image 5
CORRECT USAGE
Image 6
INCORRECT USAGE
This manual suits for next models
3
