MT MT1700-A1 User manual

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [email protected]
MEITU DIGITAL INDUSTRY CO., LIMITED 1/ 11
MT1700-A1 Manual
MeiTu Digital Industry Co.,Ltd
Add: Building 8A Caohejing Hi-Tech Park Of Pujiang, No.188 Xinjun Ring
Rd.,Minhang ,Shanghai ,China

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 2/ 11
Warning symbols
Safety
Installation, assembly and dismantling
Operation
Maintenance
Troubleshooting
Repairs
Accessories
Technical specification
General information
Full-auto Hot and Cold laminator MT1700-A1 respersent the highest industrial
product by MT for high end market. It has been the most human and efficiency
laminating machine ever. With a laminating and mounting width up to 1620mm(64''),
ensures most application possibilities.
MT1700-A1 is for extremely demanding finishing requirements. This wide format
and heavy duty laminator is designed for widest choice of finishing possibilities.
Precise air pressure and nip control offers better and easy operation experience.
Standardized emergency buttons and laser eye ensures the operator works in complete
safety.
Before first use of the MT laminator, you should carefully read this manual,
which contains important instructions, indications and safety information.
Failure to read the manual may result in serious injury to operators and damage
to machine.
Machine is heavy! Please be careful, when moving.
Table of contents
General information
Summary

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 3/ 11

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 4/ 11
Safety
In order to make a full understanding of the machine, please read this manual
carefully before operation. Take care when operating the machine, especially if more
than one operator is using it.
Safety power supply
The power supply should meet the requirement of the machine.
Safety function
The emergency stop function and the mechanical stop function for the machine should
be test in connection with installation, servicing, maintenance etc.
Safety operation
In order to make a full understanding of the machine, please read this manual
carefully before operation.
Safety maintenance
Do not use water to clean the machine in case of short circuit, electric shock or rust.In
order not to hurt the rollers, please do not put any hard stuff on the machine.
Check the wheelwork at a regular time, clean and lubricate.The rollers are mine parts

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 5/ 11
Emergency situations
In the event of an emergency, Press the emergency stop button to stop the laminator in
an emergency. Then the machine will run again and the button will bounce up, when
you clockwise rotate to the neutral position.
Red emergency stop buttons are located at the two sides of the machine.
The MT Laminator should be assembled and used in a clean room with a normal
room temperature and normal humidity levels. The work place should be dry and
ventilated. Do not use this machine near water source or wet ground. This minimises
the occurrence of static electricity. In the meanwhile, do not close to combustible and
explosive goods.
Delivery inspection
When the machine is delivered, the following units are included:
·MT laminator
·Manual
·Accessories
Connections
Voltage:
AC220/240V 50-60HZ
of the machine, damage of the rollers will affect the yields. Please rise the upper roller
up after lamination, in case of the deformation of the lower roller under long time
weight.

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 6/ 11
The MT Laminator should be placed in a dry and ventilated situation.
Before use
Check the wheelwork (at a regular time), clean and lubricate.
Using
The roller is hot during working, please do not touch it,in case of scalded or bruised.
After use
Place the roller in the idle position, raised 5 mm above the working table.
Clean the roller at a regular time, do not use water to clean the machine in case of
short circuit, electric shock or rust.
Use 80% alcohol, detergent or eraser to clean the rollers after lamination, which can
lengthen the rollers' life.
The temperature of the roller should under 40℃ and stop heating.
Do not focus on one point.
Clean the residuum in time, otherwise it will affect the yields.
Assembly with the steps performed by technician authorised.
Electrical connectors may only be connected to socked to sockets with the correct
voltage. All other operations may only be performed by authorised staff.
Positioning

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 7/ 11

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 8/ 11
Maintenance
Every day
·Make sure that the machine is not held any hard stuff and the roller is not damaged.
·check the buttons on the machine
Once a week
·clean the machine
Once a month
·Clean and lubricate the wheelwork.
·Check the power supply and the foot switch to prevent leakage.
·If you have an air compressor with laminator, check and clean with its manual.
As necessary
·Check the power supply and clean the roller.
Troubleshooting
1.Reset the emergency stop button.
2.Reset the controls
The roller won’t move up and
down
(If none of this helps, please contact
a technician)
1. Check
power
supply
or
emergency button.
Control panel dead fault
2. If the fuse is burn down, just
replace.
1. Regulate the fraction of the
rollers
2. Fix or regulate the chain wheel

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 9/ 11
key on the motor shaft
The roller can not
3. If Motor or speed controller
breakdown, Just replace the motor or
the speed controller.
run
1. Rises up the temperature
2. Clean the surface of graphic
3. If there is some problems with the
film, change the film.
Snow points
Air bubbles or folds
If this is not possible, contact MT Technical Service
TEL: [phone]
The equipment may only be used for its intended purposed as specified in
this manual. For any other use may result in damage or injury, and is at the user’s own
risk.
Accessories
For any necessary accessories you need, you can try to contact the dealer where you
bought your MT Laminator.
Printings go tilt
Folds of films
Regulate the tension of the film or
the reception roll
Contact a technician
You should first try contacting a technician through the dealer where you bought your
Laminator.
Repairs
Finished products are too
curled
1. Regulate the film roll's fraction
2. Lower the temperature
4. Put the beam weight on printings
Regulate the pressure of the rollers.
3. Improve speed or lower
temperature.
1. Adjust the pressure of the rollers.
2. Make the printings flat

MEITU DIGITAL INDUSTRY CO., LTD.
Add: 1F, Building 8A, No.188 Xinjun Ring Rd.,Minhang, Shanghai, 201114,China
(Caohejing Hi-Tech Park (CHJ) of Pujiang, Minhang )
Tel: [phone] Fax: [phone] www.mtutech.com [e-mail]
MEITU DIGITAL INDUSTRY CO., LIMITED 10 / 11
MT1700-A1
Model
MT1100-A1
1100mm
MT1700-A1
MT2300-A1
2280mm
Max width
1620mm
Speed
Up to 7m/min
Hot and Cold
Heated Infrared
130mm
Up to 7m/min
Hot and Cold
Heated Infrared
130mm
Up to 7m/min
Hot and Cold
Heated Infrared
130mm
Laminating type
Heating method
Diameter of upper
roller
Max thickness
Warm up time
30mm
30mm
30mm
10-15min
10-15min
40°C-50°C( for cold
lamination),
90°C-100°C( for hot
lamination)
120°C
10-15 min
40°C-50°C( for cold
lamination),
90°C-100°C( for hot
lamination)
120°C
Recommended temp 40°C-50°C( for cold
range
lamination),
90°C-100°C( for hot
lamination)
120°C
Max temp
Fixed Volt
AC220V-240V
50HZ-60HZ
2200W
AC220V-240V
50HZ-60HZ
2200W
AC220V-240V
50HZ-60HZ
2200W
Fixed power
Fixed current
Reverse function
Laser safety
Foot pedal switch
Dimensions
N.W.
16A
16A
16A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
660×1550×1450mm
180KG
660×2150×1450mm
210KG
660×2750×1450mm
300KG