MUBVIEW Bell-J7 User manual

WIRELESS I WIFI I OUTDOOR I WATERPROOF
A Smarter Safety Solution
FCC ID: 2AUSP-BELLJ6

Thanks for your shopping and trust.
We are keeping to optimize product and improve
our lifetime customer service to offer you a
better shopping experience. If you have any
problems, please feel free to contact us. We will
solve your problems within 24 hours. Besides,
your advice or suggestions will be much
appreciated and welcomed.
Register via link below to get 3 Years Warranty
Extension.http://bit.ly/zuReg
Product Service
Email: [email protected]
Distributor: [email protected]
About Us
Web: www.mubview.com
Facebook: www.facebook.com/mubview
Amazon Store: www.amazon.com/mubview
Warranty Service

1. Charge the Doorbell -------------------------- P1
2. Supply Power to the Chime ------------------- P1
2.1 Power by three AA batteries--------------------- P1
2.2 Power by DC 5V adapter------------------------ P1
3. What’s in the Box------------------------------- P2
4. Switch on the Doorbell ------------------------ P3
5. Download Mubview APP ---------------------- P4
6. Account Registration---------------------------- P4
7. Add Doorbell to App--------------------------- P5
7.1 Preparations for connection-------------------- P5
7.2 Connect Doorbell to App----------------------------- P5
8. Connect the Chime --------------------------- P7
8.1 Click reset button------------------------------- P7
8.2 Press your doorbell to pair up------------------- P7
8.3 Chime settings---------------------------------- P8
9. Install the Doorbell ------------------------------ P9
9.1 Select a location---------------------------------- P9
9.2 Mark the screw holes & Install the wall mount----- P10
9.3 Mount your doorbell----------------------------- P10
10. Tamper Alart Setting -------------------------- P11
11. Product specifications ------------------------- P12
INDEX PAGE

1. Charge the Doorbell
Please charge your doorbell with a DC 5V 1A~2A
phone adapter and the provided charging cable.
The LED will glow blue once fully charged.
1
Three units of AA batteries is required to make your
indoor chime 100% wire-free. And you will be free to
place your chime in almost anywhere indoors.
*Please mind the electrodes when installing batteries!
You can also plug in the provided USB cable and
connect the chime to DC 5V 1A~2A phone adapter.
2.1 Power by three AA batteries
2.2 Power by DC 5V adapter
[email protected]
Start Charging:
Fully Charging:
2. Supply Power to the Chime

2
[email protected]
Doorbell * 1
DingDong *1
Quick User Guide *1
3. What’s in the Box
NOTE: Micro SD card and power adapter are not included.
USB Cable *1
Screws Set/Screwdriver *1
3M Tape *2
WIRELESSI WIFI I OUTDOOR I WATERPROOF
ASmarter Safety Solution

Remove the wall mounting bracket and silicone cover,
switch on your doorbell. The LED indicator will flash red
(once per second), and it is ready for network setting.
4. Switch on the Doorbell
On/Of switch
Solid Red
Device is abnormal
Solid Blue
Successfully connected to WiFi network
Flashing Red Slowly (Once per second）
Ready for WiFi configuration
Flashing Blue Slowly (Once per second）
Live-viewing doorbell camera
Flashing Red Quickly (Twice per second）
Device is connecting to WiFi
Flashing Blue Quickly (Twice per second）
Upgrading doorbell firmware
3
[email protected]

4
[email protected]
Download Mubview App from Google Play™ or
App Store™. Or scan the QR codes as below, with your
smart phone.
*Google Play™ is a trademark of Google Inc. App
Store™ is a mark of Apple Inc.
NOTE: Make sure turning on both permissions below.
①Allow Mubview App to access mobile cellular data
and wireless LAN, otherwise it will fail to connect the
camera (in mobile Setting).
②Allow Mubview App to send messages, otherwise
the phone will not receive alarms when motion is
detected (in mobile Setting-Mubview).
5. Download and Install App
New user needs to sign up in Mubview App with email
address. Click 'Sign up' to create a New Account and
follow the steps to complete registration.
6. Account Registration
Android
iOS

5
[email protected]
7. Add Doorbell to App
7.1 Preparations for connection
①Insert Micro SD Card into the camera to save video
clips or you can start the 3-day free cloud service.
Without Micro SD Card or cloud service, no video will
be saved.
②The camera only support 2.4GHz Wi-Fi, not
support 5GHz.
③When connect to the network, please take the
camera close to the router(suggest within 10-15ft).
7.2 Connect Doorbell to App
Tap 'Add Device' Select 'Doorbell Camera' Power on the Camera

6
[email protected]
Reset the Camera Activate the doorbell Prepare to Scan
Scan QR Code Wait till 100% Perform Network Diagnosis

7
8. Connect the Chime
8.1 Click reset button
Click RESET on the chime, and the chime indicator on
the left will flash red for 20 seconds, indicating that the
chime is in pairing mode.
8.2 Press your doorbell to pair up
Press the doorbell button to send a pairing signal,
and your chime will sound to react, together with its
blue LED flashing. Chime pairing succeeds.
NOTE: If your home is large and you need more than
one Dingdong, please buy it on Amazon or contact
Mubview team to get extra 2.
[email protected]

8
8.3 Chime settings
Ringtone selection
Click change ringtone (4 ringtones available)
Volume control button
Level 1: 110 dB;
Level 2: 100 dB;
Level 3: 90 dB;
Level 4: 80 dB
Settings
Click to enter/quit pairing mode;
Press & hold 5 seconds to restore factory defaults
NOTE: If you need 3-day overwriting cloud storage for
half a year for free, please contact us to get it.
Email: [email protected]
[email protected]

9. Install the Doorbell
9.1 Select a location
You can purchase the following angled brackets so
as to point your doorbell to a specific view angle.
Corner Mount
(Not included)
25 to 50 degree
angle adjustable
Wedge Mount
(Not included)
8 degrees stackable
wedge mount unit
9
[email protected]

9.2 Mark the screw holes & Install the wall mount
1.Take apart the wall mount from your doorbell and mark
the location of the two mounting holes on your wall.
10
All set! Congrats!
[email protected]
2.Screw your bracket into wood wall with the provided
screws. If installing on stucco, brick, or
concrete, drill holes in the wall, then insert the included
anchors before driving in the mounting screws.
9.3 Mount your doorbell
Attach your doorbell to the mounting bracket and snap
the doorbell to make sure it reaches the bottom. Then
secure it with the provided starsharpped security screw.

Kindly notice the anti-theft alarm in doorbell settings.
10. Tamper Alart Setting
11
Tamper Alert on
Once the doorbell is detached from the
bracket, a 30-sec alarm will be triggered.
Meanwhile, video recording will be activated,
and alarm notification will be pushed to the
owner’s APP account.
Tamper Alert off
The owner can disable the tamper alarm in
doorbell settings, and detach the doorbell for
battery recharging or maintainance.
[email protected]

12
11. Product Specifications
Video Doorbell Model No.: Bell J7
Wireless Chime Model No.: Chime 06
[email protected]