MUBVIEW Bell-J9 User manual

A Smarter Safety Solution
Bell-J9
WIRELESS I WIFI I OUTDOOR I WATERPROOF
FCC ID: 2AUSP-BELLJ6

Thanks for your shopping and trust.
We have been optimizing our products and improve
our lifetime customer service to offer you a better
shopping experience. If you have any problems,
please feel free to send us an E-mail. We will solve
your problems within 24 hours. In addition, your
advice or suggestions will be much appreciated
and welcomed.
Register via link below to get 3 Years Warranty
Extension.
https://bit.ly/3zBSB2y
Product Service
Email: [email protected]
Distributor: [email protected]
More About Us
Web: www.mubview.com
Facebook: www.facebook.com/mubview
Amazon Store: www.amazon.com/mubview
Warranty Service

INDEX PAGE
1. What’s in the Box -------------------------- P1
2. Meet the Doorbell ------------------------ P2
3. Download and Install App ---------------- P3
4. Account Registration --------------------- P3
5. Add Doorbell to App --------------------- P4
5.1 Preparations for Connection -------------- P4
5.2 Connect Doorbell to App -----------------P4
6. Charge your Doorbell -------------------- P6
7. Set up Doorbell -------------------------- P7
8. Pair With Your Indoor Chime -------------- P8
9. Install Your Doorbell ---------------------- P10
10. Product Specifications ------------------P12

ASmarter Safety Solution
Bell-J9
A SMARTER SAFETY SOLUTION
Doorbell * 1
DingDong *1
Quick User Guide *1
1. What’s in the Box
NOTE: Micro SD card and power adapter are not included.
1
USB Cable *1
Screws Set/Screwdriver *1
3M Tape *2

2
2. Meet the Doorbell
Camera
PIR Motion Sensor
Microphone
Doorbell Button
LED Indicator
Charging
Indicator
Micro -SD
Card Slot
Unlock Hole
Li-ion Battery
Built-in
Speaker
Unlock Pin
Reset Button
Micro USB Port
Doorbell comes with a 4,800mAH rechargeable battery.

3
Download Mubview App from Google Play™ or
App Store™. Or scan the QR codes as below, with your
smart phone.
*
Google Play™ is a trademark of Google Inc. App Store™ is a mark of Apple Inc.
NOTE: Make sure turning on both permissions below.
①Allow
Mubview App to access mobile cellular data
and wireless LAN, otherwise it will fail to connect the
camera (in mobile Setting).
②Allow
Mubview App to send messages, otherwise
the phone will not receive alarms when motion is
detected (in mobile Setting-Mubview).
3. Download and Install App
New user needs to sign up in Mubview App with email
address. Click 'Sign up' to create a New Account and
follow the steps to complete registration.
4. Account Registration

4
5. Add Doorbell to App
5.1 Preparations for connection
①Insert Micro SD Card into the camera to save video
clips or you can start the 3-day free cloud service.
Without Micro SD Card or cloud service, no video will
be saved.
②The camera only support 2.4GHz Wi-Fi, not
support 5GHz.
③When connect to the network, please take the
camera close to the router(suggest within 10-15ft).
5.2 Connect Doorbell to App
Tap 'Add Device' Select 'Doorbell Camera' Power on the Camera

5
Reset the Camera Activate the doorbell Prepare to Scan
Scan QR Code Wait till 100% Perform Network Diagnosis

Prior to the doorbell installation, please charge up your
doorbell for about 8-10 hours till the charging LED turns
BLUE from RED.
Solid red
USB compatible mobile phone charger (DC 5V 1A~2A).
Battery charging
Fully chargedSolid blue
6. Charge your Doorbell
LED STATUS
Compatible charger (not provided):
INDICATION
6

7
LED Indicator
Press your doorbell to activate, and you will see the
LED indicator flashes red (once per second). If not
press and hold reset button for 5 seconds to
restore factory defaults.
· Please operate the setup near your Wi-Fi router.
· Make sure your phone connect to a 2.4GHz Wi-Fi.
· Make sure the doorbell is turned on and its indicator
LED is flashing red. If not, press and hold RESET for 5
seconds.
· Ensure the Wi-Fi signal is good, and the Wi-Fi
password is correct.
Tips
7. Set up Doorbell
Solid red Device is abnormal
Ready for Wi-Fi configuration
Connecting to Wi-Fi
Device is online
LiVe-viewing doorbell cam
Firmware upgrading
Flash red (once/sec)
Flash red (twice/sec)
Solid blue
Flash blue (once/sec)
Flash blue (twice/sec)
LED STATUS INDICATION
Rest Button
RESET
DC5V